Mp3/Wma/Aac; Audio; Ipod; Indication For Cd Player - Alpine CDE-147BT Manual

• The CD is being improperly inserted.
– Make sure the CD is being inserted following instructions in the
CD Player Operation section.
Unable to fast forward or backward the CD.
• The CD has been damaged.
– Eject the CD and discard it; using a damaged CD in your unit can
cause damage to the mechanism.
CD playback sound skips due to vibration.
• Improper mounting of the unit.
– Securely re-mount the unit.
• The disc is very dirty.
– Clean the disc.
• The disc has scratches.
– Change the disc.
• The pick-up lens is dirty.
– Do not use a commercially available lens cleaner disc. Consult
your nearest Alpine dealer.
CD playback sound skips without vibration.
• The disc is dirty or scratched.
– Clean the disc; damaged disc should be replaced.
Error displays (built-in CD player only).
• Mechanical error
– Press . After the error indication disappears, insert the disc
again. If the above-mentioned solution does not solve the problem,
consult your nearest Alpine dealer.
CD-R/CD-RW playback not possible.
• Close session (finalization) has not been performed.
– Perform finalization and attempt playback again.

MP3/WMA/AAC

MP3, WMA or AAC is not played back.
• Writing error occurred. The MP3/WMA/AAC format is not
compatible.
– Make sure the MP3/WMA/AAC has been written in a supported
format. Refer to "About MP3/WMA/AAC" on page 15, then
rewrite in the format supported by this device.

Audio

The sound is not output from the speakers.
• Unit has no output signal of the internal amplifier.
– POWER IC is switched to "ON", refer to "Connecting to an
External Amplifier (POWER IC)" on page 19.

iPod

iPod does not play and no sound is output.
• The iPod has not been recognized.
– Reset this unit and the iPod. Refer to "Initial System Start-Up" on
page 10. To reset the iPod, refer to the Owner's Manual of the iPod.

Indication for CD Player

• No CD is inserted.
– Insert a CD.
• Although a disc is inserted, "NO DISC" is displayed and the unit does
not start to play or eject the disc.
– Remove the disc by following these steps:
Press the  button again for at least 2 seconds.
If the disc still does not eject, consult your Alpine dealer.
48
-EN
• Mechanism error.
1 Press the  button and eject the CD.
If not ejecting, consult your Alpine dealer.
2 When the error indication remains after ejecting, press the 
button again.
If the error indication still does not turn off after pressing the 
button for a few times, consult your Alpine dealer.
• When "ERROR" is displayed:
If the disc cannot be ejected by pressing , press the RESET switch
(Refer to "Initial System Start-Up" on page 10) and press  again.
If the disc still cannot be ejected, consult your Alpine dealer.
• A copy-protected WMA file was played back.
– You can only play back non-copy-protected files.
• A sampling rate/bit rate not supported by the unit is used.
– Use a sampling rate/bit rate that is supported by the unit.

Indication for Flash Memory

NO USB DEVICE
• A Flash Memory is not connected.
– Make sure the Flash Memory device is correctly connected.
• Database error or decoder error.
– You can solve the problem by switching the source.
• Communication error or boot error, etc.
– You can solve the problem by reconnecting the Flash Memory, or
format the Flash memory.
• Abnormal current is run to the USB Flash Memory device.
– You can solve the problem by switching the source.
• No song (file) is stored in the Flash Memory.
– Connect the Flash Memory device after storing songs (files).
• A sampling rate/bit rate not supported by the unit is used.
– Use a sampling rate/bit rate that is supported by the unit.