Drill Master 94245 Set Up And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Drill Master Manuals
  4. Saw
  5. 94245
  6. Set up and operating instructions manual

Drill Master 94245 Set Up And Operating Instructions Manual

7-1/4 inch circular saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

7-1/4 INCH CIRCULAR SAW
Set Up ANd OpeRAtINg INStRUCtIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVe tHIS MANUAL.
Copyright
2006 by Harbor Freight Tools
©
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual Revised 10e
Model
94245
. All rights reserved. No portion of this manual or any artwork
®

Advertisement

Table of Contents
loading

Related Manuals for Drill Master 94245

Summary of Contents for Drill Master 94245

  • Page 1 7-1/4 INCH CIRCULAR SAW Model 94245 Set Up ANd OpeRAtINg INStRUCtIONS Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVe tHIS MANUAL. Copyright 2006 by Harbor Freight Tools .

  • Page 2: Important Safety Information

    NOtICe is used to SAVe tHIS MANUAL address practices not Keep this manual for the safety warnings related to personal injury. and precautions, assembly, operating, CAUtION, without the inspection, maintenance and cleaning safety alert symbol, is procedures. Write the product’s serial number used to address practices not in the back of the manual near the assembly related to personal injury.
  • Page 3 ranges and refrigerators. There is an up or carrying the tool. Carrying increased risk of electric shock if your power tools with your finger on the body is grounded. switch or energizing power tools that have the switch on invites accidents. do not expose power tools to rain or wet conditions.

  • Page 4: Circular Saw Safety Warnings

    with the switch is dangerous and must Circular Saw Safety Warnings be repaired. dANgeR: Keep hands away from disconnect the plug from the power cutting area and the blade. Keep your source and/or the battery pack from second hand on auxiliary handle, the power tool before making any or motor housing.
  • Page 5 Causes and Operator prevention of the kerf and check that saw teeth Kickback: are not engaged into the material. If saw blade is binding, it may walk up or • Kickback is a sudden reaction to a kickback from the workpiece as the saw pinched, bound or misaligned saw is restarted.
  • Page 6 to damaged parts, gummy deposits, or a the workpiece. This will help maintain build-up of debris. balance and control while the cut is completed. Lower guard should be retracted manually only for special cuts such Blades must be rated to at least the as ″plunge cuts″...

  • Page 7: Vibration Safety

    pacemaker interference or pacemaker conditions and situations that may occur. failure. In addition, people with It must be understood by the operator pacemakers should: that common sense and caution are • Avoid operating alone. factors which cannot be built into this • Do not use with power switch locked product, but must be supplied by the operator.

  • Page 8: Double Insulated Tools: Tools With Two Prong Plugs

    To reduce vibration, maintain the tool double insulation system which satisfies as explained in this manual. If any OSHA requirements and complies with abnormal vibration occurs, stop use the applicable standards of Underwriters immediately. Laboratories, Inc., the Canadian Standard Association, and the National SAVe tHeSe Electrical Code. INStRUCtIONS.

  • Page 9: Specifications

    Make sure the extension cord is properly SpeCIFICAtIONS wired and in good electrical condition. Power Input 120 V~, 60 Hz, 10 A (peak) Always replace a damaged extension Motor 5000 RPM, direct drive cord or have it repaired by a qualified Line Cord 18 AWG x 2 electrician before using it. Saw Blade 7-1/4”; 24 tooth carbide tipped (included)

  • Page 10: Instructions For Putting Into Use

    UNpACKINg Functions When unpacking, make sure that the item is intact and undamaged. If any parts Handle grip are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. INStRUCtIONS FOR pUttINg INtO USe Read the eNtIRe IMpORtANt SAFetY INFORMAtION section at the beginning of this manual including all text under depth Lever (38) subheadings therein before set up...

  • Page 11: Installing A Saw Blade

    Raise the Blade Guard (20) as far as OpeRAtINg INStRUCtIONS possible. See photo on the next page. Read the eNtIRe IMpORtANt Hold the Blade Guard up and press the SAFetY INFORMAtION Spindle Lock Button with one hand. section at the beginning of this Rotate the Saw Blade until the Spindle manual including all text under Lock catches and the blade stops.

  • Page 12: Work Piece/Area Set Up

    Use the appropriate type of blade for the Work piece and Work Area Set Up material you are cutting. Work piece selection: Work piece must be free of foreign objects and loose knots. Do not use to cut logs, tree limbs, or uneven lumber.

  • Page 13: Pocket Cuts

    or clamp a straight edge to the material When the Base Plate is resting flat on to guide the saw on a straight path. the stock being cut, proceed cutting in a Refer to photo above. forward direction to the end of the cut. Place the saw Base Plate on the material When the cut is complete, release the to be cut.

  • Page 14: Cleaning, Maintenance, And Lubrication

    Regularly inspect and tighten all MAINteNANCe ANd mounting screws and knobs. SeRVICINg Keep Saw Blade clean and sharp. Sharp Procedures not specifically blades minimize stalling and kickback. explained in this manual must Keep guards in good working order. be performed only by a qualified technician.

  • Page 15: Troubleshooting

    tROUBLeSHOOtINg Symptom possible Cause Remedy Saw does not start when No power to line cord. Check electrical outlet for power. trigger is pulled. Switch Lock Button not pushed in Press in button while pulling while pulling trigger. trigger. Defective switch. Replace switch. Carbon brushes dirty or worn Clean or replace carbon brushes.

  • Page 16: Parts List

    pARtS LISt part description Q’ty part description Q’ty Guide Fence Spring Round-head Rivet Blade Guard Lever Guide Fence Screw Fender Ring Base Plate Screw M6x16 Depth Lever Angle Bracket Washer Retaining Ring Shelf Carriage Bolt M6x10 Carriage Bolt M6x14 Washer Hex Bolt M6x16 Wing Nut M6 Bearing 6000Z Blade Cover Fender Ring...

  • Page 17: Assembly Diagram

    ASSeMBLY dIAgRAM REV 10e SKU 94245 For technical questions, please call 1-800-444-3353. Page 17...

  • Page 18: Limited 90-Day Warranty

    To take advantage of this warranty, LIMIted 90 dAY WARRANtY the product or part must be returned to us Harbor Freight Tools Co. makes every with transportation charges prepaid. Proof effort to assure that its products meet of purchase date and an explanation of the high quality and durability standards, and complaint must accompany the merchandise.

Table of Contents