Drill Master 61204 Owner's Manual And Safety Instructions
  1. Manuals
  2. Brands
  3. Drill Master Manuals
  4. Saw
  5. 61204
  6. Owner's manual and safety instructions
Drill Master 61204 Owner's Manual And Safety Instructions

Drill Master 61204 Owner's Manual And Safety Instructions

Hide thumbs Also See for 61204:
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Drill Master 61204

Summary of Contents for Drill Master 61204

  • Page 2: Table Of Contents

    4. DON’T USE IN DANGEROUS ENVIRONMENT. to do a job for which it was not designed. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. Page 2 For technical questions, please call 1-888-866-5797. Item 61204...
  • Page 3 It’s safer than using your hand and it frees both hands to operate tool. 21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. Item 61204 For technical questions, please call 1-888-866-5797. Page 3...
  • Page 4 9. Wear a full face shield over ANSI- protection. Eye protection must be ANSI-approved approved safety goggles during use. and breathing protection must be NIOSH-approved for the specific hazards in the work area. Page 4 For technical questions, please call 1-888-866-5797. Item 61204...

  • Page 5: Vibration Safety

    If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUcTIONS. Item 61204 For technical questions, please call 1-888-866-5797. Page 5...

  • Page 6: Specifications

    Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Functions Handle Trigger Stationary Moveable Guard Guard Angle Guide Clamp Blade Base Figure A Page 6 For technical questions, please call 1-888-866-5797. Item 61204...

  • Page 7: Operation

    Knob. give a clear tone. If cracked, there will be a dead sound and not a clear ring. 10. Lower the Housing and replace the Safety Chain. Item 61204 For technical questions, please call 1-888-866-5797. Page 7...
  • Page 8 Base. e. Flip the Quick Release down onto the Clamp threads. f. Push the Clamp against the workpiece. g. Tighten the Handle clockwise to secure the workpiece. Page 8 For technical questions, please call 1-888-866-5797. Item 61204...

  • Page 9: Work Piece And Work Area Set Up

    4. Plug the Power Cord into a 120V~ then store the tool indoors out of children’s reach. grounded, electrical outlet. 5. Squeeze and hold the Trigger to start the Saw. Item 61204 For technical questions, please call 1-888-866-5797. Page 9...

  • Page 10: Maintenance

    Storage area must be kept dry, and above that have been dropped or bumped. freezing. Any grinding or cut-off wheels exposed to humidity or freezing temperatures must not be used. Page 10 For technical questions, please call 1-888-866-5797. Item 61204...

  • Page 11: Troubleshooting

    If an extension cord is needed, use one with the proper diameter for its length and load. See Table A on page 3. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. Item 61204 For technical questions, please call 1-888-866-5797. Page 11...
  • Page 12 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 12 For technical questions, please call 1-888-866-5797. Item 61204...
  • Page 13 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 61204 For technical questions, please call 1-888-866-5797. Page 13...

  • Page 14: Parts List And Diagram

    19# Bearing Ø6 Washer Rotor Cable Guard Brush Holder Power Cord Brush Cable Press Plate Ø4x14 S/T Screw 18# Bearing Ø  7 /8" Flange Stator Pin Wrench 100# Pull Spring Flat Spanner Page 14 For technical questions, please call 1-888-866-5797. Item 61204...

  • Page 15: Assembly Diagram

    Assembly Diagram Item 61204 For technical questions, please call 1-888-866-5797. Page 15...

  • Page 16: Warranty

    Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.

Table of Contents