Advertisement
Quick Links
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2019 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Grinding Wheel Sold Separately
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
21b
Advertisement
Related Manuals for Drill Master 61204
Summary of Contents for Drill Master 61204
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
-
Page 2: Table Of Contents
4. DON’T USE IN DANGEROUS ENVIRONMENT. to do a job for which it was not designed. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted. Page 2 For technical questions, please call 1-888-866-5797. 61204... - Page 3 12. SECURE WORK. Use clamps or a vise to hold leave tool until it comes to a complete stop. work when practical. It’s safer than using your hand and it frees both hands to operate tool. 61204 For technical questions, please call 1-888-866-5797. Page 3...
- Page 4 8. Wear a full face shield over ANSI- protection. Eye protection must be ANSI-approved approved safety goggles during use. and breathing protection must be NIOSH-approved for the specific hazards in the work area. Page 4 For technical questions, please call 1-888-866-5797. 61204...
- Page 5 If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SaVE tHESE inStructiOnS. 61204 For technical questions, please call 1-888-866-5797. Page 5...
-
Page 6: Safety
Assembly Diagram near the end of this manual. Functions Safety Button Handle (on other side of handle) Stationary Guard trigger Swing Guard angle Guide Vise clamp Vise Knob cut-Off Wheel (Grinding) Base Page 6 For technical questions, please call 1-888-866-5797. 61204... -
Page 7: Operation
Grinding Wheel, noting the orientation of each. d. An undamaged wheel will ring with a clear tone. If cracked, there will be a dead sound and not a clear ring. 61204 For technical questions, please call 1-888-866-5797. Page 7... - Page 8 3. To reposition the Angle Guide for a different- sized workpiece, remove both of the Bolts, and reattach the Angle Guide at the other set of screw holes. See Figure D. Screw Holes Figure D: repositioning the angle Guide Page 8 For technical questions, please call 1-888-866-5797. 61204...
- Page 9 Trigger to start the Saw. Allow the Saw and secure with the Safety Chain. Clean, Grinding Wheel to attain full speed. then store the tool indoors out of children’s reach. 61204 For technical questions, please call 1-888-866-5797. Page 9...
-
Page 10: Maintenance
Storage area must be kept dry, and above that have been dropped or bumped. freezing. Any grinding or Cut-Off Wheels exposed to humidity or freezing temperatures must not be used. Page 10 For technical questions, please call 1-888-866-5797. 61204... - Page 11 If an extension cord is needed, use one with the proper diameter for its length and load. See table a on page 3. Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power supply before service. 61204 For technical questions, please call 1-888-866-5797. Page 11...
- Page 12 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 12 For technical questions, please call 1-888-866-5797. 61204...
- Page 13 Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175364210 when ordering parts. 61204 For technical questions, please call 1-888-866-5797. Page 13...
-
Page 14: Parts List And Diagram
Swing Guard Spring Washer Spring Bolt Inner Flange Bolt Grinding Wheel (sold separately) Screw Outer Flange Safety Chain (not shown) Arbor Bolt Adapter 5/8" (not shown) Spring Adapter 7/8" (not shown) Page 14 For technical questions, please call 1-888-866-5797. 61204... - Page 15 Diagram 48 49 61204 For technical questions, please call 1-888-866-5797. Page 15...
-
Page 16: Warranty
Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.