Epson Stylus Color 980 Service Manual page 161

EPSON Stylus Color 980
Table 6-2. Oil Applied to the Stylus Color 980
Type Part name Content
Grease G-26 40g
Oil O-8 40g
NOTE: No adhesion is used in the Stylus Color 980.
Table 6-3. Lubrication Points Using G-26
No. Lubricating Point
Using a brush, lubricate the whole inner
1 surface of the round cutout in the right side of
the [Frame,ASF;B].
Using a brush, lubricate right and left sides of
2
the [Hopper ASSY, C].
Lubricate the inner gear of the [Combination
3
gear,14.4, 24].
Lubricate the surface of the bearing part (the
4 round cut) of the [Bushing,12] located at the
right end of the printer mechanism.
5 Lubricate the [Shaft, Pulley, Driven].
6 Lubricate the back of the [Frame, Guide, CR].
Table 6-4. Lubrication Point Using the O-8
No. Lubricating Point
Apply oil to the [Oil Pad].
1
Before lubricating, observe the CAUTION in
Section 6.2 well.
Maintenance
Part code Availability
B702600001 EPSON exclusive
1019753 EPSON exclusive
Amount Ref. figure
1 x 1 mm Figure 6-8
1 x 2 mm Figure 6-9
1 x 1 mm Figure 6-10
1 x 10 mm Figure 6-11
Figure 6-12
1 x 1 mm
1 x 150 mm Figure 6-13
Amount Ref. figure
0.7 - 0.75 cc Figure 6-14
Lubrication and Adhesion
Table 6-5. Lubrication Points
No. Lubricating Point
1 The shaft in the [Frame Assembly, DE, Right]
2 The teeth of the [Gear, 25.8]
3 The shaft in the [Frame Assembly, DE, Left]
4 The teeth of the smaller gear in the
[Combination Gear,12, 26]
5 12 points on the [Paper Guide,Front]
6 4 points in the [Grounding Plate,Paper Eject]
7 2 contact areas; between [Roller
Assembly,Paper Eject, Rear] and [Grounding
Plate, Eject]
8 2 contact areas; [Roller Assembly, Eject] and
[Grounding Plate, Eject]
9 The teeth of the right and left [Gear,27]s
10 2 points on the shaft in the [Lever Assembly,
Release,Cam]
NOTE: Do not apply lubricant to the roller
surface.
11 [Oil Pad]
Refer to Section 6.2.1 "Lubricating the Carriage
Guide Shaft".
12 A hole in the [Frame Assembly, Middle, Left]
13 Roller shaft in the [Lever Assembly, Roller
Release, Right]
14 Pin on the [Frame, Middle, Right]
15 Narrow end of the [Shaft, Arm Lifter]
Revision A
Amount
G-26 ( 1 x 10 mm)
G-26
( 1mm x 1/3 of the circle)
G-26 ( 1 x 10 mm)
G-26
( 1mm x 1/3 of the circle)
G-26 ( 1 x 2 mm)
G-26 ( 1 x 2 mm)
G-26 ( 1 x 2 mm)
G-26 ( 1 x 2 mm)
G-26
( 1mm x 1/4 of the circle)
G-26 ( 1 x 2 mm)
O-8 (0.7 - 0.75 cc)
G-26 ( 1 x 3 mm)
G-26 ( 1 x 1 mm)
G-26 ( 1 x 3 mm)
G-26 ( 1 x 2 mm)
157