Page 4
English Legend 1 Soluble product bins 12 Green LEDS 23 Sugar dispenser 2 Water tank 13 Red LEDS 24 Automatic rinsing jumper 3 Coffee hopper cover 14 Green LED “Ready for use” 25 Drain cover/Dispensing point 4 Coffee bean hopper 15 Red LED “Water empty”...
English VENDING MACHINE FOR HOT BEVERAGES D.A. 7P 1 - GENERAL INFORMATION 1.1 Manual purpose • Purpose of this manual is informing user of all functions of the vending machine, simplifing its use and achieving the highest performances. 2 - TECHNICAL FEATURES 2.1 Machine description •...
English 4 - CONTROLS • Main swicth: placed on the machine rear side, below on the right. • Selection panel: consisting of 7 selection buttons (11) which correspond to the same number of beverages marked as A-B-C-D-E-F-G. • Display (16): displays the inserted coln value. •...
Page 7
English 5.4 Set up • Fill the water tank (2) (except for those machines directly connected to the waterline), the coffee bean hopper (4) and the soluble product bin (1), paying attention not to fill the latter over 2/3 of their max. capacity and to set them in the right position (Pos.1 Tea or other drinks, Pos.2 Chocolate, Pos.3 Milk) (Fig.B).
English 6 - OPERATION 6.1 Beverage Dispensing • Select a beverage among those available and check the corresponding amount. • Insert coins into the slot (17) until the required amount is displayed on the coin display (16). N.B. If you insert a higher amount, the machine will neither return change nor retain the credit.
English • Attention: The cup tubes hold only cups with a max. diameter of 70 mm. and a max. length of 90 mm. • Sugar dispenser • Put the packets into the special dispenser, located behind the front door panel. •...
Page 10
English clockwise and remove it. Wipe the mixing blade with sponge and lukewarm water, without pressing too hard as not to compromise the positioning of the seal gasket. • Wash with warm water all parts and reinstall them, repeating backwards the above-mentioned operations. Pay special attention to re-install correctly the nozzle with silicone tube.
English 9 - AUXILIARY FUNCTIONS : • The machine is provided with some special controls which allow following operations: • Front panel LED test • Descaling boiler • Calibration of soluble product specific weight • Access to the special controls: •...
English 10 - MB7P CABINET - INSTALLATION AND USE • The M.B.7P cabinet allows a greater autonomy and increases the supply interval. • Remove the cabinet from its packing as well as all parts contained in the inside of the cabinet. •...
English 11 - NRI G13 COIN VALIDATOR PROGRAMMING • The vending machine is normally equipped with NRI G13 coin validator which can recognize up to 6 different coins or money pieces. • Values of the programmed coins are given in table (50), positioned next to the coin validator(TK 2007 and TK 2008 point out 24 mm.
Page 14
DEUTSCHLAND: ITALIA SAECO Handelsgesellschaft mbH SAECO S.p.A. Hermann-Laur-Str. 4 Via Torretta D-78253 Eigeltingen I - 40041 GAGGIO MONTANO (Bologna) Tel.: 07774/50510 Tel.: 0534-30009 Fax: 07774/50597 Fax: 0534-31125 ÖSTERREICH: SAECO Kaffeemaschinen Bahnhofstr. 9 A-6922 Wolfurt Tel.: 05574/30550 Tel.: 05574/6777 - NEU ab 19.11.1993 Fax: 05574/30360 Fax: 05574/6777-77 - NEU ab 19.11.1993...
Need help?
Do you have a question about the D.A. 7P and is the answer not in the manual?
Questions and answers