Zones 2-4 Setup; Default Setup - Rotel RSP-1570 Owner's Manual

46 46
Zone 2–4 Setup
��������������������
�����������������������
������������������
���������������������������
������������������������
������������������
��������������������
�������������������
�����������������������������������
������������
The ZONE SETUP menu provides settings and configuration options
related to the operation of the remote zones. This menu is reached by
highlighting the ZONE line on the MAIN menu and pressing ENTER.
ZONE: Specifies the zone to configure, ZONE 2, 3, or 4. Each zone is
configured individually.
SOURCE: Specifies a source for listening in the selected zone. Options
are CD, TUNER, TAPE, VIDEO 1–5, SOURCE, and OFF. Selecting the
SOURCE option links the zone source to the source selected for the main
zone so that the remote zone will hear the same source as the main
zone. Selecting the OFF option turns the zone off.
VIDEO INPUT: Specifies a video source (Composite Video only) for the
selected zone. The options available are Composite 1, 2 and 3 and OFF.
(If SOURCE, above, is set to OFF, the VIDEO INPUT selection will not be
available.)
VOLUME SETUP: configures the remote zone outputs for VARIABLE
or FIXED volume levels. VARIABLE allows control of the volume settings
in the remote zone from the RSP-1570's front panel or from a remote
control/IR repeater in the zone. FIXED output disables the volume
control. In this mode, the remote zone level can be fixed at the level
specified on the next line, thus optimizing system performance when
sending a fixed level signal to a preamp or amplifier with its own volume
adjustment.
VOLUME: In VARIABLE output mode, this line shows the current volume
setting for remote zone. In FIXED output mode, this volume setting
establishes a permanent fixed output level for the remote zone.
Move the highlight to the desired line using the UP/DOWN buttons and
use the +/– buttons to adjust the volume level. To return to the MAIN
menu, press the ENTER button. Press the MENU/OSD button on the
remote to cancel the display and return to normal operation.
TURN ON VOL: Specifies a default volume level to be used each time
the remote zone is activated. You can select LAST to have the zone
activate with the last previously used volume setting. Or, you specify a
volume from MIN (full mute) to MAX, in 1dB increments. Note that this
setting cannot exceed the MAX VOL established in the next line of the
menu.
MAX VOL: Specifies the maximum volume level for the remote zone.
The volume cannot be adjusted above this level. Settings range from
MIN to MAX, in 1dB increments.
12V TRIGGER: The RSP-1570 has six 12V trigger outputs (labeled
1–6) that supply a 12V DC signal to turn on Rotel components and other
components as needed. This menu item turns on specific 12V trigger
RSP-1570 Surround Sound Processor RSP-1570 Surround Sound Processor
outputs whenever the indicated zone is activated. The six 12V Trigger
outputs may be assigned to each Zone and can send a turn-on signal
to remote components whenever the Zones are activated. For example,
Zone 2 could use 12V Triggers 1, 3 and 6; Zone 3, 12V Triggers 2 and
3; Zone 4, 12V Triggers 5 and 6.
1. Press the +/– buttons on the remote to change the first position from
blank to 1 (activating TRIGGER 1 for that zone).
2. Press the ENT button on the remote to move to the next position.
3. Repeat until all six positions are set as desired. A final press of the
ENT button confirms the selection.

Default Setup

���������������������
�����������
���������
�������������������
�����
�������������������
�������������������
�������������������
�������������
The DEFAULT SETUP menu provides access to four functions:
• Restore all features and settings to the original FACTORY DEFAULT
settings.
• Memorize a custom group of settings as a USER DEFAULT.
• Activate the memorized USER DEFAULT settings.
• Set a NEW PASSWORD for the memorized USER DEFAULT settings.
To restore the FACTORY DEFAULT settings: Place the highlight
on the FACTORY DEFAULT line using the UP/DOWN buttons and use
the +/– buttons to change the setting to YES. Press the ENTER button
to proceed with resetting the FACTORY DEFAULT settings with re-
confirmation screen. The unit will power off (to Standby Mode) and then
on, with the factory settings restored. To return to the MAIN menu without
resetting the FACTORY DEFAULT settings, change the entry to NO and
press the ENTER button.
Note: Resetting to factory default settings will erase all stored
settings including delay settings, speaker settings, balance settings,
input settings and more. You will lose ALL system configuration
settings. Be certain that you wish to do so before resetting the
factory defaults.
To memorize USER DEFAULT settings: Many of the current
configuration settings can be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.To save the current settings
as a USER DEFAULT:
1. Place the highlight on the SET USER DEFAULT line using the UP/
DOWN buttons and use the +/– buttons to change the setting to YES.
2. Press the ENTER button to go to confirmation screen where a
password must be entered. The default password is 8888. If the