Default Setup - Rotel RSX-1560 Owner's Manual

50 50
outputs may be assigned to each Zone and can send a turn-on signal
to remote components whenever the Zones are activated. For example,
Zone 2 could use 12V Triggers 1, 3 and 6; Zone 3, 12V Triggers 2 and
3; Zone 4, 12V Triggers 5 and 6.
1. Press the +/– buttons on the remote to change the first position from
blank to 1 (activating TRIGGER 1 for that zone).
2. Press the ENT button on the remote to move to the next position.
3. Repeat until all six positions are set as desired. A final press of the
ENT button confirms the selection.

Default Setup

���������������������
�����������
��������������������������
�����������������������������
���������
�������������������
�����
�������������������
�������������������
�������������������
�������������
The DEFAULT SETUP menu provides access to six functions:
• Set the tuning function for North American or European frequencies.
• Redirect the Front channel amplifiers or the Center Back channel
amplifiers to power remote speakers in Zone 2, 3 or 4, or redirect the
Center Back channel amplifiers to 'Front' for bi-amping.
• Restore all features and settings to the original FACTORY DEFAULT
settings.
• Memorize a custom group of settings as a USER DEFAULT.
• Activate the memorized USER DEFAULT settings.
• Set a NEW PASSWORD for the memorized USER DEFAULT settings.
To change the TUNER setting: Place the highlight on the TUNER
SETTING line using the UP/DOWN buttons and use the +/– buttons
to change the setting to N. AMERICA or EUROPE. Then, move the
highlight to the FACTORY DEFAULT line and change the setting to YES
as described above. The screen will change to a confirmation screen.
Press the ENTER button to proceed with resetting the FACTORY DEFAULT
settings and changing the TUNER SETTING. To return to the MAIN menu
without resetting the FACTORY DEFAULT and TUNER settings, change the
entry to NO and press the ENTER button.
To change the REDIRECT setting: Place the highlight on the REDIRECT
line using the UP/DOWN buttons and use the +/– buttons to change the
setting from REDIRECT: No to REDIRECT: Front>Zone 2, Front>Zone 3
or Front>Zone 4, CB>Zone 2, CB>Zone 3 or CB>Zone 4 (for powering
speakers in one of the remote Zones 2, 3 or 4), or CB>Front (for bi-
amping front speakers). If you choose to redirect the internal front
channel amplifiers, then you will need a separate stereo amplifier to
drive your front speakers.
RSX-1560 English v2.indd 50
RSX-1560 Surround Sound Receiver RSX-1560 Surround Sound Receiver
Note: Changing the default TUNER SETTING or REDIRECT
SETTING can only be done at the same time as restoring the
FACTORY DEFAULT settings. Therefore, we recommend selecting
your default TUNER and REDIRECT settings and resetting to the
FACTORY DEFAULT settings as the first step in configuring the unit,
before you change or memorize any other configuration settings.
To restore the FACTORY DEFAULT settings: Place the highlight
on the FACTORY DEFAULT line using the UP/DOWN buttons and use
the +/– buttons to change the setting to YES. Press the ENTER button
to proceed with resetting the FACTORY DEFAULT settings with re-
confirmation screen. The unit will power off (to Standby Mode) and then
on, with the factory settings restored. To return to the MAIN menu without
resetting the FACTORY DEFAULT settings, change the entry to NO and
press the ENTER button.
Note: Resetting to factory default settings will erase all stored
settings including delay settings, speaker settings, balance settings,
input settings and more. You will lose ALL system configuration
settings. Be certain that you wish to do so before resetting the
factory defaults.
To memorize USER DEFAULT settings: Many of the current
configuration settings can be stored as a USER DEFAULT, which can be
activated at any time from this menu screen.To save the current settings
as a USER DEFAULT:
1. Place the highlight on the SET USER DEFAULT line using the UP/
DOWN buttons and use the +/– buttons to change the setting to YES.
2. Press the ENTER button to go to confirmation screen where a
password must be entered. The default password is 8888. If the
entered password is correct, the current settings will be saved as the
new USER DEFAULT settings.
3. To return to the MAIN menu without saving changes, change all
entries on the screen to NO and press ENTER.
Note: If there is insufficient memory to store a USER DEFAULT
configuration file, the SET USER DEFAULT option will not be
available.
To activate memorized USER DEFAULT settings: After you have
stored a USER DEFAULT configuration file, you can activate those settings
at any time by placing the highlight on the USER DEFAULT line using the
UP/DOWN buttons. Use the +/– buttons to change the setting to YES.
Press the ENTER button to proceed with activating the USER DEFAULT
settings. To return to the MAIN menu without activating the USER
DEFAULT settings, change the entry to NO and press the ENTER button.
To return to the MAIN menu without activating the USER DEFAULT
settings, change the entry to NO and press the ENTER button.
To change the password: The password programmed at the factory is
0000. If you wish to change the password:
1. Place the highlight on the SET NEW PASSWORD line using the UP/
DOWN buttons. Use the +/– buttons to change the setting to YES.
Press the ENTER button to proceed to the PASSWORD screen.
29/9/08 15:16:21