Table of Contents
Advertisement
POWER: This setting determines how the
RSX-1065 powers up. With the default DIRECT
setting, the unit is fully activated when AC power
is applied and the front-panel POWER button
is pressed in; however, it may be put in
STANDBY mode using the remote POWER
button. With the STANDBY setting, the unit pow-
ers up in standby mode when AC is applied
and the front-panel POWER button is in the
ON position. The unit must be activated us-
ing the remote control POWER button. In AL-
WAYS-ON mode, the unit remains fully active
whenever AC is present and the front-panel
POWER button is pressed in; the remote
POWER button is disabled and the unit can-
not be put in standby mode.
OSD: Determines whether the ON-SCREEN
DISPLAYS are shown on your TV monitor dur-
ing operation.
LANGUAGE: Selects one of the two lan-
guages for all of the ON-SCREEN MENUS:
English or German (Deutsch).
Change settings on the OTHER OPTIONS menu
by highlighting the desired line using the UP/
DOWN buttons and using the +/– buttons to
step through the available settings. To return
to the MAIN menu, press the ENTER button.
Press the MENU key on the remote to cancel
the display and return to normal operation.
29
DEFAULT SETUP Menu
DEFAULT SETUP
TUNER SETTING: N.AMERICA
FACTORY DEFAULT: No
USER DEFAULT: No
USER DEFAULT SET: No
ENT KEY=MAIN MENU
UP KEY=up
+/– KEY=change
DWN KEY=down
DEFAULT SETUP
TUNER SETTING: N.AMERICA
FACTORY DEFAULT: Yes
USER DEFAULT: No
USER DEFAULT SET: No
ENT KEY=Exec.
UP KEY=up
+/– KEY=change
DWN KEY=down
The DEFAULT SETUP menu provides access to
four functions:
• Restoring all features and settings to the
original FACTORY DEFAULT settings.
• Changing the tuning functions and displays
for use in North America or Europe.
• Memorizing a custom group of settings as
a USER DEFAULT.
• Activating the USER DEFAULT settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the setting
to YES. The screen will change to a confirma-
tion screen. Press the ENTER button to proceed
with resetting the FACTORY DEFAULT settings.
The unit will power off and then on, with the
factory settings restored. To return to the MAIN
menu without resetting the FACTORY DEFAULT
settings, change the entry to NO and press
the ENTER button.
: Resetting to factory default settings will
NOTE
erase all stored settings including delay set-
tings, speaker settings, balance settings, in-
put settings and more. You will lose ALL system
configuration settings. Be certain that you wish
to do so before resetting the factory defaults.
To change the TUNER setting: Place the
highlight on the TUNER SETTING line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to N. AMERICA or
EUROPE. Then, move the highlight to the FAC-
TORY DEFAULT line and change the setting to
YES as described above. The screen will
change to a confirmation screen. Press the EN-
TER button to proceed with resetting the FAC-
TORY DEFAULT settings and changing the
TUNER SETTING. To return to the MAIN menu
without resetting the FACTORY DEFAULT and
TUNER settings, change the entry to NO and
press the ENTER button.
: Changing the default TUNER SETTING
NOTE
can only done at the same time as restoring
the FACTORY DEFAULT settings. Therefore,
we recommend selecting your default TUNER
SETTING and resetting to the FACTORY DE-
FAULT settings as the first step in configuring
the unit, before you change or memorize any
other configuration settings.
To save USER DEFAULT settings: Many
of the current configuration settings can be
stored as a USER DEFAULT, which can be
activated at any time from this menu screen.
To save the current settings as a USER DEFAULT
Place the highlight on the USER DEFAULT SET
line using the UP/DOWN buttons and use the
+/– buttons to change the setting to YES. The
screen will change to a confirmation screen.
Press the ENTER button to store the new USER
DEFAULT settings. To return to the MAIN menu
without saving any changes, change all en-
tries on the screen to NO and press the EN-
TER button.
: If there is insufficient memory to store a
NOTE
USER DEFAULT configuration file, the USER
DEFAULT SET option will not be available.
To activate memorized USER DEFAULT
settings: After you have stored a USER DE-
FAULT configuration file, you can activate those
settings at any time by placing the highlight
on the USER DEFAULT line using the UP/
DOWN buttons. Use the +/– buttons to change
the setting to YES. The screen will change to
a confirmation screen. Press the ENTER but-
ton to proceed with activating the USER DE-
FAULT settings. To return to the MAIN menu
without activating the USER DEFAULT settings,
change the entry to NO and press the EN-
TER button.
English
Advertisement
Table of Contents
