Zone 2 Setup; Default Setup - Rotel RSX-1057 Owner's Manual

Zone 2 Setup

ZONE2 SETUP
SOURCE:Off
VOLUME SETUP:Variable
VOLUME:60
TURN ON VOL:Last
MAX VOL:Max
12V TRIGGER:Off
MAIN MENU
The ZONE 2 SETUP menu provides settings
and configuration options related to the op-
eration of Zone 2. This menu is reached by
highlighting the ZONE 2 line on the MAIN
menu and pressing ENTER.
SOURCE: Specifies a source for listening
in Zone 2. Options are CD, TUNER, TAPE,
VIDEO 1–5, SOURCE, and OFF. Selecting
the SOURCE option links the Zone 2 source
to the source selected for the main zone so
that Zone 2 will hear the same source as the
main zone. Selecting the OFF option turns
Zone 2 off.
VOLUME SETUP: configures the Zone 2
outputs for VARIABLE or FIXED volume lev-
els. VARIABLE allows control of the volume
settings in Zone 2 from the RSX-1057 front
panel or from a remote control/IR repeater
in Zone 2. FIXED output disables the Zone
2 volume control. In this mode, the Zone 2
level can be fixed at the level specified on
the next line, thus optimizing system perfor-
mance when sending a fixed level signal to
a preamp or amplifier with its own volume
adjustment.
VOLUME: In VARIABLE output mode, this
line shows the current volume setting for
Zone 2. In FIXED output mode, this volume
setting establishes a permanent fixed output
level for Zone 2.
Move the highlight to the desired line using
the UP/DOWN buttons and use the +/– but-
tons to adjust the volume level. To return to
the MAIN menu, press the ENTER button.
Press the MENU/OSD button on the remote
to cancel the display and return to normal
operation.
45
TURN ON VOL: Specifies a default volume
level to be used each time Zone 2 is acti-
vated. You can select LAST to have Zone 2
activate with the last previously used volume
setting. Or, you specify a volume from MIN
(full mute) to MAX, in 1dB increments. Note
that this setting cannot exceed the MAX VOL
established in the next line of the menu.
MAX VOL: Specifies the maximum volume
level for Zone 2. The volume cannot be ad-
justed above this level. Settings range from
MIN to MAX, in 1dB increments.
12V TRIGGER: The RSX-1057 has three12V
trigger outputs that supply a 12V DC signal
to turn on Rotel components and other com-
ponents as needed. The 12V Trigger labeled
ZONE 2 is assigned to Zone 2 and can send
a turn-on signal to remote components when-
ever Zone 2 is activated. Select the appro-
priate setting from eight options to have the
ZONE 2 trigger output send the turn-on sig-
nal. The options that will activate the Zone
2 trigger are: zone, 1+zone, 2+zone, and
ALL. The options that will disable the Zone
2 trigger are: 1, 2, 1+2, and No.

Default Setup

DEFAULT SETUP
TUNER SETTING:N.America
FRONT REDIRECT:Front
FACTORY DEFAULT:No
USER DEFAULT:No
SET USER DEFAULT:No
MAIN MENU
The DEFAULT SETUP menu provides access
to six functions:
• Set the tuning function for North Ameri-
can or European frequencies.
• Redirect the front channel amplifiers to
power center back speakers or speakers
in Zone 2 speakers.
• Restore all features and settings to the
original FACTORY DEFAULT settings.
• Memorize a custom group of settings as
a USER DEFAULT.
• Activate the memorized USER DEFAULT
settings.
To change the TUNER setting: Place the
highlight on the TUNER SETTING line using
the UP/DOWN buttons and use the +/– but-
tons to change the setting to N. AMERICA
or EUROPE. Then, move the highlight to the
FACTORY DEFAULT line and change the set-
ting to YES as described above. The screen
will change to a confirmation screen. Press
the ENTER button to proceed with resetting
the FACTORY DEFAULT settings and changing
the TUNER SETTING. To return to the MAIN
menu without resetting the FACTORY DEFAULT
and TUNER settings, change the entry to NO
and press the ENTER button.
To change the FRONT REDIRECT set-
ting: Place the highlight on the FRONT REDI-
RECT line using the UP/DOWN buttons and
use the +/– buttons to change the setting to
FRONT SP (for powering front speakers), CB
SP (for powering center back speakers), or
ZONE SP (for powering speakers in zone
2). If you redirect the internal amplifiers, then
you will need a separate stereo amplifier to
drive your front speakers.
: Changing the default TUNER SETTING
NOTE
or REDIRECT SETTING can only done at the
same time as restoring the FACTORY DEFAULT
settings. Therefore, we recommend selecting
your default TUNER and REDIRECT settings
and resetting to the FACTORY DEFAULT set-
tings as the first step in configuring the unit,
before you change or memorize any other
configuration settings.
To restore the FACTORY DEFAULT set-
tings: Place the highlight on the FACTORY
DEFAULT line using the UP/DOWN buttons
and use the +/– buttons to change the set-
ting to YES. Press the ENTER button to pro-
ceed with resetting the FACTORY DEFAULT
settings. The unit will power off and then on,
with the factory settings restored. To return
to the MAIN menu without resetting the FAC-
TORY DEFAULT settings, change the entry to
NO and press the ENTER button.
: Resetting to factory default settings
NOTE
will erase all stored settings including delay
settings, speaker settings, balance settings,
input settings and more. You will lose ALL
system configuration settings. Be certain that
you wish to do so before resetting the fac-
tory defaults.
English