Table of Contents
Advertisement
Pre-2004 d'Lite, Lite
& Pre-2005 Encore
Handlebar & Stroller Wheel Supplement
To be used in conjunction with 2003 or previous model
year Burley trailer Owner's Instruction & Safety Manual.
Table of Contents
I.
II.
III.
IV.
V.
VI.
VII.
VIII.
IX.
Page
2
3
3
6
7
9
9
11
12
12
Advertisement
Table of Contents
Related Manuals for Burley Pre-2004 d’Lite
Summary of Contents for Burley Pre-2004 d’Lite
-
Page 1: Table Of Contents
Pre-2004 d’Lite, Lite & Pre-2005 Encore Handlebar & Stroller Wheel Supplement To be used in conjunction with 2003 or previous model year Burley trailer Owner’s Instruction & Safety Manual. Table of Contents Page Introduction Preparation for Installation III. Handlebar Installation... -
Page 2: Introduction
The Walk n’ Roller has been designed to empower you to bicycle and stroll, all in the same trip. You can bike with your Burley as a trailer to a store or a scenic park, lock your bike and quickly convert the trailer to a stroller, without tools. The conversion from trailer to stroller, and stroller to trailer, is done without removing any Walk n’... -
Page 3: Preparation For Installation
These are covered in sections III, V, and VII. Each section has its associated part list so that you may confi rm that you have received all the parts needed. If any parts are missing contact Burley, do not proceed with installation. - Page 4 Phillips head bolt and the new standard nut provided. The nut will fi t snugly into the hex shape recess in the center of the part. Tighten securely. Burley Walk ‘n Roller Manual; models 2003 and earlier...
- Page 5 Check that the new roll bar catch and hinge parts and the roll bar is properly installed. Check the attachment points for loose elements. Failure to do so could result in serious injury. Burley Walk ‘n Roller Manual; models 2003 and earlier...
-
Page 6: Using The Handle
The button locks the handle into the receiver. Be sure that both buttons are protruding through the hole in the receivers. This will prevent the handle from coming out during use. Burley Walk ‘n Roller Manual; models 2003 and earlier... -
Page 7: Mount Wheel Assembly
(#2) and the safety strap (#4). • Save the hitch and the d-ring (#3) for reinstallation. The locking nut (#5) and the bolt (#1) can be discarded. A longer bolt is provided for the next step. Burley Walk ‘n Roller Manual; models 2003 and earlier... - Page 8 fl exible coupling is attached in the same manner, using the bolt through the tongue. The safety strap is anchored in the same way, to the wheel assembly clamp bolt. Burley Walk ‘n Roller Manual; models 2003 and earlier...
-
Page 9: Using The Walk 'N Roller Wheel
1 inch diameter, aluminum main frame tube that runs along the inside of the wheel. Undo the clamp in the brake assembly by removing the 1.5 inch long hex head bolt. Burley Walk ‘n Roller Manual; models 2003 and earlier... - Page 10 ¼ from the mark. Now tighten the bolt. Once tightened, engage the brake to verify its function. The brake post should push into the tire about ¼ inch, or half the diameter of the post. Burley Walk ‘n Roller Manual; models 2003 and earlier...
-
Page 11: Safety Guidelines
• Do not use Walk n’ Roller on stairs of escalators. • Do not use Walk n’ Roller components on any other product other than the Burley trailer for which it was designed and tested. -
Page 12: Maintenance
Burley will repair or replace any Walk n’ Roller parts it determines to be defective for the life of the trailer. The owner of a Burley trailer with Walk n’ Roller parts installed must present the trailer for repair at an authorized Burley dealer, together with an original sales receipt or similar proof of purchase.