Programming Instructions - Bulldog Security RS92 Installation And Owner's Manual

PROGRAMMING INSTRUCTIONS

ENTERING PROGRAMMING MODE
Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as
long as you want to remain in programming mode.
Adding New Transmitters
Press and hold the brake, then press and hold Button #1 (start) on the working transmitter until
the parking lights flash once. Release Button #1. Press any button on the new remote, the parking
lights will flash three (3) times, the new remote is now programmed.
Programming Automatic Start
Press and hold the brake, the press and hold Button #2 (stop) until the parking lights flash twice.
Release. Press and release Button #1 (start) the parking lights will flash once. The unit is now
programmed for Automatic Start. This feature lets the vehicle start every three (3) hours regardless
of temperature. To turn off Automatic Start, press and hold Button #1 (start) until the parking
lights flash twice. Release the brake, the parking lights will flash three (3) times. NOTE: The
factory setting is Automatic Start off.
Programming Cold Start
Press and hold the brake, then press and hold Button #2 (stop) until the parking lights flash twice.
Release Button #2. Press and hold Button #2, the parking lights will flash once. Each continuous
flash represents a progression in degrees: one (1) flash= -40ºF, two (2) flashes=-30ºF, three (3)
flashes=-20ºF, four (4) flashes=-10ºF, five (5) flashes=0ºF, six (6) flashes=10ºF, seven (7)
flashes=20ºF. To disable Cold Start, press and hold Button #2 until the parking lights flash seven
(7) times, then two (2) quick flashes 8 and 9. The Cold Start is now disabled. Release the brake,
the parking lights will flash three (3) times, the programming is now entered. NOTE: The factory
setting is Cold Start off.
Programming Hot Start
Press and hold the brake, then press and hold Button #2 (stop) until the parking lights flash twice.
Release Button #2. Press and hold Button #3, the parking lights will flash once. Each continuous
flash represents a progression in degrees: one (1) flash= 160ºF, two (2) flashes=150ºF, three (3)
flashes=140ºF, four (4) flashes=130ºF, five (5) flashes=120ºF, six (6) flashes=110ºF, seven (7)
flashes=100ºF. To disable Hot Start, press and hold Button #3 until the parking lights flash seven
(7) times, then two (2) quick flashes 8 and 9. The Hot Start is now disabled. Release the brake,
the parking lights will flash three (3) times, the programming is now entered. NOTE: The factory
setting is Hot Start off.
NOTE: Only Cold and Hot Start functions can be enabled at the same time. If button #1 is pressed
for programming, Cold/Hot Start is disabled. When Buttons #2 and #3 are pressed, then the Automatic
and Low Voltage Starts are disabled.
Programming Tach/Tachless Start
Press and hold the brake, then press and hold Button #3 (finder) until the parking lights flash
three (3) times. Release Button #3. Press and release Button #4, the parking lights will flash
once. The unit is now in Tachless Start Mode. Press and release Button #4, the parking lights will
flash twice. The unit is now in Tach Start Mode. Release the brake, the parking lights will flash
three (3) times. The programming is now entered. NOTE: Factory setting is Tachless Start Mode.
Programming Runtime
(Can be changed without entering programming mode)
Your engine must be off. Press and hold Button #2, within 10 seconds the parking lights will begin
to flash. Release Button #2 when the desired time has been reached. The maximum time is 15 minutes
or 3 flashes. To check runtime, press and release Button #2 and the unit will indicate how long
the runtime is with flashing the parking lights (each flash equals 5 minutes of runtime).
8