1. Manuals
  2. Brands
  3. Bulldog Security Manuals
  4. Remote Starter
  5. RS1300E
  6. Installation and owner's manual

Bulldog Security RS1300E Installation And Owner's Manual

Alarm and remote control starter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

INSTALLATION GUIDE

ALARM AND REMOTE CONTROL STARTER
CONTENTS
System Features ......................................
System Components ....................................
Required Tools .......................................
Technical Assistance ..................................
Before You Begin......................................
Precautions ..........................................
Using your Test Probe ................................. 3
Making Connections..................................
Locating & Making Connections ....................... 4-6
Neutral Safety Switch............................... 6-7
Connecting Wiring Harness ............................. 7
Antenna Placement ....................................
Optional Connections................................ 7-9
How to use Your Remote Transmitter .................... 10
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
MODEL RS1300E
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1
1
1
2
2
2
3-4
7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RS1300E and is the answer not in the manual?

Questions and answers

Related Manuals for Bulldog Security RS1300E

Summary of Contents for Bulldog Security RS1300E

  • Page 1: Table Of Contents

    INSTALLATION GUIDE • OWNER’S GUIDE ALARM AND REMOTE CONTROL STARTER MODEL RS1300E CONTENTS System Features ........System Components ........Required Tools ........Technical Assistance ........Before You Begin........Precautions .......... Using your Test Probe ......... 3 Making Connections........Locating & Making Connections ....... 4-6 Neutral Safety Switch.......

  • Page 2: System Features

    SYSTEM FEATURES 2 Four-Button Extended Range Remotely start your car to run the heater, air conditioning or defroster from an extended Remote Controls distance. Keyless Entry Remotely locks and unlocks your power door locks. Built In Alarm Features Provides door, hood and impact protection. Horn and Siren Output Lets you choose between the vehicle’s factory horn or an optional six tone siren.

  • Page 3: Technical Assistance

    It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry. Enjoy your new remote starter for years to come! This remote system is designed to start your vehicle by sending a command signal from the remote transmitter.

  • Page 4: Using Your Test Probe

    USING YOUR TEST PROBE To operate your test probe, connect the black clip to a good chassis ground. Connect the red clip to a good 12V positive source. If the test probe is connected correctly, both the green and the red lights will be dimly illuminated.

  • Page 5: Locating & Making Connections

    2. Twist upper wires together, twist lower wires together as shown. 3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires up to meet the left wire as shown. 4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown.
  • Page 6 1. If your vehicle has only one (1) ignition wire, as most 1993 and older domestic and import vehicles do, connect the heavy gauge WHITE wire to it. 2. If your vehicle has two (2) ignition wires, as most 1994 and newer vehicles do, connect the heavy gauge RED with WHITE stripe wire to the Ignition 2 wire.

  • Page 7: Neutral Safety Switch

    PARKING LIGHTS (+12V only with parking lights on) NEGATIVE PARKING LIGHT DIAGRAM ONLY Turn the parking lights to the ON position. (NOT YOUR HEADLAMPS). Optional part #775 required. Probe the wire(s) coming from your headlamp control switch. The correct wire will show +12V and the RED light will glow bright only when the parking lights are ON.

  • Page 8: Connecting Wiring Harness

    PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE PRE-1996 DODGE DAKOTAS Optional part #775 required. Optional part #775 required. YELLOW YELLOW Driver’s Door Switch Driver’s Door Switch WHITE WHITE Ground BLACK/LT.BLUE Tie into BLACK heavy white Tie into FUSE BLACK Ground wire on...
  • Page 9 light will glow bright on both the lock and the unlock wires. Press and hold the lock button on the switch and test the lock wire. The correct wire will test (+) positive and the RED light will glow bright. Release the lock button and this wire should show a (-) negative and the GREEN light will glow bright.

  • Page 10: Operator Programming Instructions

    DOME LIGHT Optional part #775 required. To determine if your dome light is turned on with (+) To Dome Light YELLOW positive or (-) negative trigger, probe for a wire in the Circuit driver’s side kick panel that switches polarity when the door is closed, then opened.
  • Page 11 Automatic Start - On Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press and release Button #1. The parking lights will flash once. The automatic start is programmed ON. Release the brake, the parking lights will flash three (3) times. NOTE: Factory setting is OFF. Automatic Start - Off Press and hold brake.

  • Page 12: How To Use Your Remote Transmitter

    Clearing the Memory of the Unit Press and hold the brake pedal, now cycle the key in the ignition switch from OFF to RUN (not start) five (5) times within four (4) seconds. Release the brake and try the remote. The unit should not function with the remote.

Table of Contents