Connecting The 12-Pin Harness And The 4-Relay Harness; Neutral Safety Switch - Bulldog Security RS92 Installation And Owner's Manual

AUXILIARY INPUT
If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 12-pin
harness to the second or third channel (-) output of your existing alarm. When the output is
activated, a (-) signal will be supplied to the remote starter.
CONNECTING THE 12-PIN HARNESS & 4-RELAY HARNESS
WHT/BLK 16 ga.
WHITE 16 ga.
YEL/BLK 16 ga.
For Passlock I
WHT/BLK 16 ga
For Passlock II
WHITE 16 ga
YELLOW
ANTENNA
For Passlock I
Keep as
YEL/BLK 16 ga
straight as
possible,
tape end Tap here when
to hold
installing bypass
straight.
module 721.

NEUTRAL SAFETY SWITCH

PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE – Optional part #775 required.
MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only)
When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you
must: Use the diagram below to create a circuit that will prevent the remote starter from starting
the vehicle unless the key is removed from the ignition switch.
Driver's Door Switch
TAN
Key
Cylinder
Ground
GREEN
Message
center or
key buzzer
GREEN/BLACK (-) Tach Input
BLUE/WHITE
(-) To hood pin switch
BLUE
(-) Aux. alarm channel input
VIOLET
(not used)
WHITE/RED
(-) Factory Alarm Shutdown
WHITE/ORANGE
(not used)
ORANGE
(+) Brake Input
BROWN
(+) Parking lights
GRAY (-) Negative Horn Output
YELLOW
Ignition input
BLACK
Ground
RED
To +12V constant
750ma (-)
Outputs
RED
2 Red wires need
RED
+12V constant.
WHITE
Either white wire
to Ignition 1. If
WHITE
your car has 2
ignitions use both.
YELLOW/BLACK
To Starter/Crank
Wire
To Accessory
Wire(s) that run
WHITE/BLACK
the Heater/Blower
Motor. Attach at
the ignition switch
wire harness only.
YELLOW
87
WHITE
Tie into
86
heavy white
87a
wire on
4-relay
5 Amp
harness
fuse
30
Ground
BLUE
(-) Negative
hood pin wire
CAUTION: Before connecting the 12-pin harness
to the module, double check all connections
to be sure they are secure and properly wrapped
with electrical tape. Mount the unit under
the driver's side dash. Make sure to properly
place antenna. (See antenna placement page
7.) Plug the 12-pin harness into the main
control module. Once it is plugged in, press
and release transmitter button #4, the parking
lights flash 3 times. The flash confirms that
the transmitter code has been programmed to
the unit. Once the module is programmed,
connect the 3-pin harness from the 4-relay
harness to the module. NOTE: There are (2)
wires in the 12-pin harness that will not be
used. All unused wires must be taped.
Press the start button, the parking lights
will flash once and the vehicle will start
and run. NOTE: If your vehicle does not start
and run you may have a factory anti-theft
system. Refer to page 7 to see if this applies
to your vehicle.
Driver's Door Switch
85
BLACK
BLACK/LT.BLUE
RED
Key
Cylinder
NOT USED,
TAPE OFF
LT.BLUE/GREEN
center or
key buzzer
PRE-1996 DODGE DAKOTAS
Optional part #775 required.
Tie into
WHITE
heavy white
Ground
wire on
4-relay
5 Amp
harness
fuse
(-) Negative
hood pin wire
Message
YELLOW
Ground
87
85
86 BLACK
87a
30
RED
BLUE
NOT USED,
TAPE OFF
6