1. Manuals
  2. Brands
  3. Bulldog Security Manuals
  4. Remote Starter
  5. RS302
  6. Installation and owner's manual

Bulldog Security RS302 Installation And Owner's Manual

Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual

INSTALLATION GUIDE

•
OWNER'S GUIDE
VEHICLE STARTER • MODEL RS302
CONTENTS
System Features ......................................1
System Components ....................................1
Required Tools .......................................1
Technical Assistance .................................1
Before You Begin .....................................1
Precautions ..........................................2
Testing Your Wires ...................................2
Making Connections .................................2-3
Locating & Making Connections ......................4-6
Connecting 12-Pin Harness ............................7
Connecting 3-relay Harness ...........................7
Anti-Theft System ....................................7
Neutral Safety Switch ................................7
Operating Instructions ...............................8
Technical Assistance
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RS302 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Bulldog Security RS302

Summary of Contents for Bulldog Security RS302

  • Page 1: Table Of Contents

    INSTALLATION GUIDE • OWNER’S GUIDE VEHICLE STARTER • MODEL RS302 CONTENTS System Features ........1 System Components ........1 Required Tools ........1 Technical Assistance .........1 Before You Begin ........1 Precautions ..........2 Testing Your Wires ........2 Making Connections .........2-3 Locating & Making Connections ......4-6 Connecting 12-Pin Harness ......7 Connecting 3-relay Harness ......7 Anti-Theft System ........7...

  • Page 2: System Features

    It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry. Enjoy your new remote starter for years to come! This remote system is designed to start your vehicle by sending a command signal from the remote transmitter or by programming automatic temperature or timed start.

  • Page 3: Precautions

    PRECAUTIONS This system is designed to be used with fuel-injected, automatic transmission vehicles only. SAFETY FIRST! Never start your vehicle if it is indoors, if the keys are in the ignition and you’re sure the car is in park. A periodic safety check is recommended to ensure that your system is in proper working order. DO NOT use mechanical wiring connections, such as crimp or snap together taps.
  • Page 4 5. Wrap the wire around one side then the other and finally around itself as shown. 6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have just connected along side the wire you connected to, tape and wire tie them together.

  • Page 5: Locating & Making Connections

    LOCATING & MAKING CONNECTIONS Please see the wiring chart on our website, www.bulldogsecurity.com. CONSTANT POWER (+12V, key in any position including off) These wire(s) are in your vehicle’s main ignition harness, usually located on the steering column coming from the ignition switch. Probe each wire with your test light. The correct wire(s) will show +12V when the ignition switch is in these 5 positions (ACC-LOCK-OFF-RUN-CRANK).

  • Page 6: Optional Connections

    BRAKE INPUT The brake wire is located on the switch near and above the brake pedal. The correct wire will show +12V only when the brake is pressed. Connect the BLUE wire from the 12-pin harness to this wire. FACTORY ALARM SHUT DOWN WIRE (FASD) (-) If your vehicle is equipped with a factory alarm system (as most vehicles with a factory keyless entry are) probe for a small gauge wire (usually found in the driver’s side kick panel) that shows (-) ground when the door lock cylinder is turned to the unlock position using the key.
  • Page 7 locking and unlocking the doors with the driver’s side switch (usually the master switch). The test light should illuminate in both switch positions. Now attach the clip end of your test light to +12V constant, probe both wires one at a time again. The light should then illuminate again only in reverse order.

  • Page 8: Connecting 12-Pin Harness

    CONNECTING THE 12-PIN HARNESS & 3-relay HARNESS CAUTION: Before connecting the 12-pin (-) Ignition 2 WHITE/BLACK harness to the module, double check all (-) Ignition 1 WHITE connections to be sure they are secure (-) Starter/Crank YELLOW/BLACK and properly wrapped with electrical tape. (-) Factory alarm shutdown BLUE/WHITE Mount the unit under the driver’s side...

  • Page 9: Operating Instructions

    OPERATING INSTRUCTIONS If you are operating your RS302 from an existing alarm’s second channel output NOTE: You may have to disarm your alarm before starting the car. 1. Before turning off the vehicle, always remember to set the heater or air conditioning for proper temperature desired. 2.

Table of Contents