Programming Instructions - Bulldog Security RS102 Owner's Manual

TRUNK RELEASE OUTPUT (Optional Part #775
required)
Locate the trunk release wire coming from
the back of the trunk release switch. To
determine if your trunk release is tripped
by a (+) positive or a (-) negative (most
trunk release switches are (+) positive).
Place one end of your test light to ground,
probe the wire. Press the "Trunk" button,
if the test light illuminates, you have a
(+) positive trunk release. If it does not,
connect the test light to +12V constant
and probe the wire. If the test light
illuminates when the button is pressed,
then you have a (-) negative trunk release.
Connect the WHITE WITH RED STRIPE wire to
the WHITE wire of the optional relay.
Please use figures below for correct
connections.
AUXILIARY INPUT
If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 18-pin
harness to the second or third channel (-) output of your existing alarm. When the output is
activated, a (-) signal will be supplied to the remote starter.
OPERATOR PROGRAMMING INSTRUCTIONS
ENTERING PROGRAMMING MODE
Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as
long as you want to remain in programming mode. The only exception is when a different remote has
been learned. The unit will exit the programming mode simply by releasing the brake and the parking
lights will flash three (3) times.
Adding Additional Remotes
Press and hold brake. Next, press and hold Button #1 on the working remote until the parking lights
flash once. Release. Press and release Button #4 on the new remote. The parking lights will flash
three (3) times confirming that the new remote was learned.
Cold Start On and Off (Degree Select)
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press
and hold Button #2. Each parking light flash is a progression in degrees. Flash #1 is -40ºF, flash
#2 is -30ºF, flash #3 is -20ºF, flash #4 is -10ºF, flash #5 is 0ºF, flash #6 is +10ºF, flash #7 is
+20ºF. Two quick flash parking light flashes is Cold Start Off. Release the brake, the parking lights
will flash three (3) times. NOTE: Factory setting is OFF.
Door Lock Pulse Length (Long)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times.
Release. Press and release Button #1. The parking lights will flash once, the door lock pulse length
will be 3.5 seconds of output. Release the brake, the parking lights will flash three (3) times.
(For European type door locks)
Door Lock Pulse Length (Short)
Press and hold brake. Next, press and hold Button #3, the parking lights will flash three (3) times.
Release. Press and release Button #1. The parking lights will flash twice, the door lock pulse
length will be 0.7 seconds of output. Release the brake, the parking lights will flash three (3)
times. NOTE: Factory setting is SHORT pulse length.
Tach Mode - ON
Press and hold brake. Press and hold Button #3, the parking lights will flash three (3) times.
Release. Press and release Button #4, the parking lights will flash twice. The Tach Start is
programmed ON. Release the brake, the parking lights will flash three (3) times.
Tachless Mode - ON
Press and hold brake. Press and hold Button #3, the parking lights will flash three (3) times.
Release. Press and release Button #4, the parking lights will flash once. The Tachless Start is
programmed ON. NOTE: Factory setting is Tachless Start ON. Release the brake, the parking lights
will flash three (3) times.
NEGATIVE TRUNK RELEASE
Optional part #775 required.
TO FACTORY TRUNK WIRE
YELLOW
WHITE
87a
WHITE/RED
FROM ALARM
BLUE
RED
THE RED WIRE IS NOT USED, TAPE OFF.
POSITIVE TRUNK RELEASE
TO FACTORY TRUNK WIRE
BLACK
WHITE
87a
WHITE/RED
FROM ALARM
RED
+12 VOLT FUSED
AT 10 AMPS
YELLOW
BLACK
BLUE
+12 VOLT FUSED
AT 20 AMPS
9