Table of Contents
Advertisement
INSTALLATION GUIDE
REMOTE STARTER MODELS RS92 / RS92E
CONTENTS
System Features .......................................
System Components .....................................
Required Tools ........................................
Technical Assistance ..................................
Before You Begin ....................................
Precautions ...........................................
Testing Your Wires ....................................
Making Wiring Connections............................ 2-4
Locating & Making Connections ........................ 4-5
Neutral Safety Switch ................................. 6
Antenna Placement (E Models)........................... 7
Anti-Theft System .....................................
Factory Anti-Theft System.............................. 7
How to use Your Remote Transmitter ..................... 7
Programming Instructions .............................. 8
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1
1
1
1
1-2
2
2
7
Advertisement
Table of Contents
Related Manuals for Bulldog Security RS92
Summary of Contents for Bulldog Security RS92
-
Page 1: Table Of Contents
INSTALLATION GUIDE • OWNER’S GUIDE REMOTE STARTER MODELS RS92 / RS92E CONTENTS System Features ........System Components ........Required Tools ........Technical Assistance ........Before You Begin ........Precautions ........... Testing Your Wires ........Making Wiring Connections......2-4 Locating & Making Connections ......4-5 Connecting the 12-Pin Harness and the 4-Relay Harness...6 Neutral Safety Switch ......... -
Page 2: System Features
SYSTEM FEATURES Four-Button Extended Range Remotely start your car to run the heater or air conditioning from an extended distance. Remote Control Instant Panic Works as personal protection. The horn sounds and the lights flash for 30 seconds. Car Finder The horn will sound and the lights will flash to help you locate your vehicle in a crowded parking lot. -
Page 3: Precautions
Since there are many different makes and models of vehicles, look at the wiring chart on or our website, www.bulldogsecurity.com/wires.htm. Read this manual thoroughly before starting the installation. You must decide if the parking light option is desired. An optional part #775 will be needed. Please do not skip any steps. TACH/TACHLESS OPERATION In most cases the decision to go with tachless mode will save time during the installation. - Page 4 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. 4. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 6.
-
Page 5: Locating & Making Connections
4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING &... - Page 6 CHASSIS GROUND Factory Bolt Black Ground Wire Locate an easy to get to bolt or screw Note: Remove any paint below located under the driver’s side of the dash and attach the BLACK ground wire from the 11-pin the spade connector. Spade Connector harness securely as pictured.
-
Page 7: Connecting The 12-Pin Harness And The 4-Relay Harness
AUXILIARY INPUT If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 12-pin harness to the second or third channel (-) output of your existing alarm. When the output is activated, a (-) signal will be supplied to the remote starter. CONNECTING THE 12-PIN HARNESS &... -
Page 8: Antenna Placement (E Models)
ANTENNA PLACEMENT ANTENNA For best results, run the antenna (YELLOW WIRE WITH Antenna Wire BLACK TIP from the back of the unit) as straight as possible. Do not place the antenna next to any Antenna Tube metal parts or the vehicle’s main computer control module. -
Page 9: Programming Instructions
PROGRAMMING INSTRUCTIONS ENTERING PROGRAMMING MODE Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want to remain in programming mode. Adding New Transmitters Press and hold the brake, then press and hold Button #1 (start) on the working transmitter until the parking lights flash once.