Table of Contents
Advertisement
NEUTRAL SAFETY SWITCH
PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE – Optional part #775 required.
MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only)
When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you
must: Use the diagram below to create a circuit that will prevent the remote starter from starting
the vehicle unless the key is removed from the ignition switch.
Driver's Door Switch
TAN
Key
Cylinder
Ground
GREEN
Message
center or
key buzzer
ANTENNA PLACEMENT
Run the antenna wire up the windshield pillar on
the driver's side and across the top of the
windshield tucking the antenna wire inside the
headliner, behind the rearview mirror. Plug the
RED 4-pin harness from the antenna into the RED
connector on the back of the unit. It will perform
best if mounted below the dark windshield tint.
See diagram below. Each receiver is tested to more
than 1/4 mile of clear air reception. While many
times you will see 1/2 mile or more. Many factors
will affect the range, including the amount of radio signals in the area, battery strength, window
tint, etc.
CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS
5-Pin
Door Lock Harness
DOOR LOCK
& UNLOCK
OUTPUT
WHT/BLK 16 ga.
ANTENNA
WHITE 16 ga.
PLUG
YEL/BLK 16 ga.
For Passlock I
WHT/BLK 16 ga
For Passlock II
WHITE 16 ga
For Passlock I
YEL/BLK 16 ga
Tap here when
installing bypass
module 721.
YELLOW
87
WHITE
Tie into
86
heavy white
87a
wire on
4-relay
5 Amp
harness
fuse
30
BLUE
(-) Negative
hood pin wire
BROWN/BLACK
(-) Diesel output
GREEN/BLACK
(+) Diesel output
BLACK/WHITE
Tach (-) to neg. side of coil
BLACK/BLUE
(-) To hood pin switch
BLUE
Do Not Use
VIOLET
(-) Dome light supervision
WHITE/RED
(-) Trunk release
ORANGE
(-) Starter immobilizer output
BROWN
(+) Parking lights
GRAY
(+) Siren output
GRAY/BLACK
(-) Horn output
YELLOW
Ignition input
BLUE/BLACK
(+) Brake switch
BLACK/YELLOW
(+) Positive door pin
GREEN
(-) Negative door pin
RED/BLACK
(-) Factory alarm shutdown
BLACK
Ground
RED
To +12V constant
750ma (-) Output
RED
2 Red wires need
RED
+12V constant.
WHITE
Either white wire to
Ignition 1. If your
WHITE
car has 2 ignitions
use both.
YELLOW/BLACK
To Starter/Crank
Wire
WHITE/BLACK
To Heater/Blower
Motor Wire
85
BLACK
BLACK/LT.BLUE
Ground
RED
Key
Cylinder
NOT USED,
TAPE OFF
LT.BLUE/GREEN
Antenna Wire
Control Module
CAUTION: Before connecting the 18-pin harness
to the module, double check all connections to
be sure they are secure and properly wrapped
with electrical tape. Make sure you mount the
unit under the driver's side dash and secure
the unit in place with 2 wire ties. Make sure
to properly place the antenna, see antenna
placement above. Next, plug the RED antenna
plug into the main control module. Make sure
you plug the 18-pin harness and the 3-pin from
the 4-relay harness into the main module.
NOTE: Make sure you have plugged in the 4-pin
plug from the antenna into the main unit before
using the remote or the unit will not receive
the signal from the transmitter.
Press the start button, the parking lights will
flash once and the vehicle should start and
run. If your vehicle does not start and run you
may have a factory anti-teft system. Refer to
pages 9 to see if this applies to your vehicle.
If the vehicle does start and run and you wish
at this time to install your door locks, proceed
to pages 9-10.
PRE-1996 DODGE DAKOTAS
Optional part #775 required.
Driver's Door Switch
Tie into
WHITE
heavy white
Ground
wire on
4-relay
5 Amp
harness
fuse
(-) Negative
hood pin wire
Message
center or
key buzzer
Antenna Tube
YELLOW
Ground
87
85
BLACK
86
87a
30
RED
BLUE
NOT USED,
TAPE OFF
8
Advertisement
Table of Contents
