Neutral Safety Switch - Bulldog Security RS102 Owner's Manual

NEUTRAL SAFETY SWITCH

MECHANICAL NEUTRAL SAFETY SWITCH (Rear Wheel Drive Only)
When installing a Bulldog remote starter on GM vehicles or Dodge Dakotas built prior to 1996, you
must:
Use the diagram below to create a circuit that will prevent the remote starter from starting the
vehicle unless the key is removed from the ignition switch.
Driver's Door Switch
TAN
Ground
Key
Cylinder
GREEN
Message
center or
key buzzer
DO NOT USE RED WIRE, TAPE OFF
CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS
WHT/BLK 16 ga.
WHITE 16 ga.
YEL/BLK 16 ga.
For Passlock I
WHT/BLK 16 ga
YELLOW
For Passlock II
WHITE 16 ga
ANTENNA
Keep as
straight as
For Passlock I
possible,
YEL/BLK 16 ga
tape end
to hold
straight.
Tap here when
installing bypass
module 721.
PRE-1996 GM REAR WHEEL DRIVES WITH PURPLE CRANK WIRE
Optional part #775 required.
YELLOW
WHITE
87
Tie into 86
heavy white
FUSE
87a
wire on
4-relay
5 Amp
harness
fuse
30
BLUE
(-) Negative
hood pin wire
BROWN/BLACK
(+) or (-) Door Lock pulse
GREEN/BLACK (-) or (+) Door Unlock pulse
BLACK/WHITE
Tach (-) to neg. side of coil
BLACK/BLUE
(-) To hood pin switch
BLUE
(-) Aux. alarm channel input
VIOLET
(-) Dome light supervision
WHITE/RED
(-) Trunk release
ORANGE
(not used)
BROWN
(+) Parking lights
GRAY
(not used)
GRAY/BLACK (not used)
YELLOW
Ignition input
BLUE/BLACK
(+) Brake switch
BLACK/YELLOW
(not used)
GREEN (not used)
RED/BLACK
(-) Factory alarm shutdown
BLACK
Ground
RED
To +12V constant
750ma (-)
Outputs
RED
RED
WHITE
WHITE
YELLOW/BLACK
WHITE/BLACK
BLACK/LT.BLUE
Ground
85 BLACK
Key
Cylinder
RED
LT.BLUE/GREEN
CAUTION: Before connecting the 18-pin
harness to the module, double check all
connections to be sure they are secure
and properly wrapped with electrical tape.
Mount the unit under the driver's side
dash. Make sure to properly place antenna.
(See antenna placement page 15.) Plug the
18-pin harness into the main control
module. Once it is plugged in, press and
release transmitter button #4, the parking
lights flash 3 times. The flash confirms
that the transmitter code has been
programmed to the unit. Once the module
is programmed, connect the 3-pin harness
from the 4-relay harness to the module.
NOTE: There are several wires in the 18-
pin harness that will not be used. All
unused wires must be taped.
Press the start button, the parking lights
will flash once and the vehicle will start
and run. If your vehicle starts and remains
running and you wish to connect your door
locks, proceed to page 16, "Testing Door
Locks", and follow the provided instructions.
NOTE: If your vehicle does not start and
run you may have a factory anti-theft
2 Red wires need
system. Refer to pages 15 and 21 to see
+12V constant.
if this applies to your vehicle.
Either white wire
to Ignition 1. If
your car has 2
ignitions use
both.
To Starter/Crank
Wire
To Accessory
Wire(s) that run
the Heater/Blower
Motor. Attach at
the ignition
switch wire
harness only.
PRE-1996 DODGE DAKOTAS
Optional part #775 required.
Driver's Door Switch
WHITE
Tie into
heavy white
FUSE
Ground
wire on
4-relay
harness
(-) Negative
hood pin wire
Message
center or
key buzzer
DO NOT USE RED WIRE, TAPE OFF
YELLOW
Ground
87
85
86 BLACK
87a
5 Amp
fuse
30
RED
BLUE
6