Table of Contents
Advertisement
Programming Shock Sensor On and Off (See Adjusting Shock Sensor)
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release
Button #4. Press and release Button #2, the parking lights will flash once the shock sensor is now ON. Press and
release Button #2, the parking lights will flash twice the shock sensor is now OFF. Release the brake, the parking
lights will flash three (3) times. The programming is now entered. NOTE: Factory setting is Shock Sensor on.
Programming Automatic Start Options
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash twice. Release
Button #2. Press and release Button #1, the parking lights will flash once. You are now in 3 hour Start Mode. Your
vehicle will start every three (3) hours. Press and release Button #1 a second time. The parking lights will flash
twice for Low Voltage Start. To discontinue automatic start options, press and release Button #1 a third time. The
parking lights will flash three (3) times, the Automatic Start Option is now off. Release the brake, the parking
lights will flash three (3) times. The programming is now entered. NOTE: The factory setting is Automatic Start
Option off.
Programming Cold Start
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash twice. Release
Button #2. Press and hold Button #2, the parking lights will flash once. Each continuous flash represents a progression
in degrees: one (1) flash= -40ºF, two (2) flashes=-30ºF, three (3) flashes=-20ºF, four (4) flashes=-10ºF, five (5)
flashes=0ºF, six (6) flashes=10ºF, seven (7) flashes=20ºF. To disable Cold Start, press and hold Button #2 until
the parking lights flash seven (7) times, then two (2) quick flashes 8 and 9. The Cold Start is now disabled. Release
the brake, the parking lights will flash three (3) times, the programming is now entered. NOTE: The factory setting
is Cold Start off.
Programming Hot Start
Press and hold the brake, then press and hold Button #2 (arm/disarm) until the parking lights flash twice. Release
Button #2. Press and hold Button #3, the parking lights will flash once. Each continuous flash represents a progression
in degrees: one (1) flash= 160ºF, two (2) flashes=150ºF, three (3) flashes=140ºF, four (4) flashes=130ºF, five (5)
flashes=120ºF, six (6) flashes=110ºF, seven (7) flashes=100ºF. To disable Hot Start, press and hold Button #3 until
the parking lights flash seven (7) times, then two (2) quick flashes 8 and 9. The Hot Start is now disabled. Release
the brake, the parking lights will flash three (3) times, the programming is now entered. NOTE: The factory setting
is Hot Start off.
NOTE: Only Cold and Hot Start functions can be enabled at the same time. If button #1 is pressed for programming,
Cold/Hot Start is disabled. When Buttons #2 and #3 are pressed, then the Automatic and Low Voltage Starts are disabled.
SPECIAL PROGRAMMING MODE:
Valet Mode On
Press and hold the brake, turn Ignition Key to the Run position. Within five (5) seconds, press and release Button #4. The
horn will sound or the siren will chirp once, the parking lights once and the LED will flash once. Valet is now on. Release
the brake, turn the ignition key off. The LED will remain lit in valet mode.
Valet Mode Off
Press and hold the brake, turn Ignition Key to the Run position. Within five (5) seconds, press and release Button #4. The
horn will sound or the siren will chirp twice, the parking lights twice and the LED will flash twice. Valet is now off. Release
the brake, turn the ignition key off. The LED will now turn off.
Temporary Silent Arm/Disarm (This Arming Only)
Press and hold Button #2 for approximately two (2) seconds, the parking lights will flash once, the unit is now programmed for
Silent Arming. Press and release Button #2, the parking lights will flash twice, and remain on for one (1) minute, the unit is
now Disarmed.
Silent Arm/Disarm (Remains In Silent Mode Until Programmed Back On)
Press and hold Button #2 for approximately five (5) seconds, when arming, the parking lights will flash without the horn or
siren sounding. Hold until the parking lights flash three (3) times, release. Silent arming/disarming is now programmed on. To
program it back on, repeat these steps. After the parking lights flash again three (3) times, silent arming/disarming is programmed
off.
Runtime Programming (Engine Off)
Press and hold Button #4 (stop) for approximately 10 seconds. The horn will honk twice, then the parking
lights will begin to flash, each flash represents 5 minutes with the maximum being 25 minutes, 5 flashes.
Simply release button at whatever runtime you desire. To check programmed runtime, press and release Button
#4 (stop). The parking lights will flash for the amount of runtime you have programmed the unit for.
12
Advertisement
Table of Contents
