Table of Contents
Advertisement
ZPM3
Zone Paging Module
COMPLIES WITH PART 68, FCC RULES
FCC REGISTRATION NUMBER:
CD23CH-10678-PX-N
RINGER EQUIVALENCE: 0.9B
ZPM-3
ZONE PAGING MODULE
O
l
1
48V
24V
TALK BAT
TALK BAT
2
O l
3
FREE SUB
LOCK SUB
4
CONF OFF
CONF ON
5
PREANN OFF
PREANN ON
2 WAY
1 WAY
6
ZONE 1
7
ZONE 2
8
ZONE 3
TONE
NIGHT
BGM
VOL
RING
VOL
VOL
© 2011 Bogen Communications, Inc. All rights reserved.
Specifications subject to change without notice.
A
B
A
B
T
R
1
T
TI
2
R
RI
3
+24V
-24V
4
+24V
+TB
5
GS
-TB
6
EMI
EM2
7
NRC
NRC
8
NRT
NRR
9
NOA
NCA
10
CMA
CMB
11
12
NOB
NCB
MTI
MT2
13
BMBA
BMBB
14
BMSA
BMSB
15
16
BMOA
POA
POB
BMOB
17
PIA
POA
18
PIB
POB
19
TBIA
TBOA
20
TBIB
TBOB
21
Z1B
Z1A
22
23
Z2B
Z2A
Z3B
Z3A
24
RAMSEY, N.J.
54-5891-03B
1107
Advertisement
Table of Contents
Related Manuals for Bogen ZPM3
Summary of Contents for Bogen ZPM3
- Page 1 PREANN ON 2 WAY 1 WAY TBIA TBOA ZONE 1 TBIB TBOB ZONE 2 ZONE 3 TONE NIGHT RING RAMSEY, N.J. ZPM3 Zone Paging Module © 2011 Bogen Communications, Inc. All rights reserved. Specifications subject to change without notice. 54-5891-03B 1107...
- Page 2 Every effort was made to ensure that the information in this manual Always follow these basic safety precautions when installing and was complete and accurate at the time of printing. However, infor- using the system: mation is subject to change. 1.Read and understand all instructions.
-
Page 3: Table Of Contents
Description ........................Installation ........................Wall-Mounting........................2 Technical Specifications ....................Connections ........................Connection to the Telephone System ..................3 Loop Start Trunk ......................3 Ground Start Trunk ......................3 48V Capability ........................ 3 Paging Port ........................3 Station Port ........................3 Connection to the Paging System ..................5 Central-Amplified Talk/Talk Back Systems with Page-Muted BGM ........ -
Page 4: Description
The Bogen ZPM3 Zone Paging Module provides up to 3 one- or two-way paging zones, including all-call capabilities, for self- amplified or central-amplified paging systems. A night ringer feature provides night ring signaling in all zones or in a group of up to 3 user-selected zones. -
Page 5: Connections
If it is necessary to supply 48V talk battery to the trunk port, and PR terminals of the TAMB2 as if it were a loop start a 48V DC power supply (Bogen Model PRS48) is also trunk. required. Connect power supplies as shown in Figure 2. - Page 6 ZPM3 ZPM3 PAGING PORT PAGE AUDIO GROUND START TRUNK CONTACT CLOSURE (N.O.) NIGHT RING CONTACT NOTE 1 PBX ANALOG NIGHT LINE C.O. LINE (INCOMING) 24V POWER 24V POWER SUPPLY SUPPLY NOTES: NOTE: 1. EITHER USE NIGHT RING CONTACT FROM PBX OR ACTUAL NIGHT LINE 1.
-
Page 7: Connection To The Paging System
To minimize the cross talk, use tween single-zone pages and All-Call pages. The Bogen the 25V tap on the BGM amplifier and reduce high-frequency BUFEX Buffer/Expander/Volume Control should be set high BGM material by lowering the amplifier treble setting. - Page 8 BGM SOURCE ZPM3 OUTPUT BGM AMP MUSIC RING TIP GND COM 25V PAGING AMP MUSIC RING TIP GND COM 25V Figure 7 – Wiring Diagram, GND COM 25V Central-Amplified LINE MUTE System with BGM to All Unpaged Zones TALKBACK AMP (OPTIONAL) NOTES: 1.
-
Page 9: Bridging Zpm3 Units
Connections to the Paging System Bridging ZPM3 Units ZPM3 units can be linked together to provide access to more unit to connect to a specific zone. This master/slave rela- zones. Due to the potentially large number of inputs which tionship can be carried on for a large number of levels, as long as proper buffering is used. -
Page 10: Features And Controls
Volume Control Shift Change/Emergency Call The TONE VOL control adjusts the volume of the pre- The ZPM3 provides either a shift change tone or Emer- announce, confirmation, error, and Shift Change/Emer- gency call (with alert tone) in all zones or in a zone group gency Call tones. - Page 12 ZPM3 TO LOOP START TRUNK TO NORMALLY OPEN CONTACTS EXTERNAL OF SHIFT CHANGE 24V RELAY CLOCK 24V POWER SUPPLY NOTE: 1. CURRENT PAGE WILL BE RESET WITH ACTIVATION OF THE SHIFT CHANGE FEATURE. Figure 11 – Wiring Diagram, Shift Change Tone Feature ZPM3 PAGING AMP TO LOOP...
-
Page 13: Field Programming
during the programming procedure. This also makes it possible to override any incorrect zone selections made during the pro- IMPORTANT: The Subzone Lockout Switch (DIP gramming process. Switch 3) must be set to Off (O) for Field Programming. Incorrect selection of zones for a zone group can be changed When power is first applied, the following default settings during programming, however, the zone group number must be are loaded:... - Page 14 The battery backup requires four (4) AA size nickel cad- Access the ZPM3 by dialing the trunk access number or mium (NiCd) batteries, with an amp-hour rating of 450 station access number. Listen for the confirmation tone mAhr or higher. To install the batteries, remove the four (if enabled).
- Page 16 Limited Warranty; Exclusion of Certain Damages The Bogen ZPM3 Zone Paging Module is warranted to be free from defects in material and workmanship for two (2) years from the date of sale to the original purchaser. Any part of the product covered by this warranty that, with normal installation and use, becomes defective (as confirmed by Bogen upon inspection) during the applicable warranty period, will be repaired or replaced by Bogen, at Bogen’s option, pro-...