1. Manuals
  2. Brands
  3. Billion Manuals
  4. Network Router
  5. BiPAC 7300G
  6. User manual

Billion BiPAC 7300(G User Manual

(802.11g) adsl2+ router
Hide thumbs Also See for BiPAC 7300(G:
Table of Contents

Advertisement

Quick Links

Download this manual
BiPAC 7300(G)
(802.11g) ADSL2+ Router
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BiPAC 7300(G and is the answer not in the manual?

Questions and answers

Related Manuals for Billion BiPAC 7300(G

Summary of Contents for Billion BiPAC 7300(G

  • Page 1 BiPAC 7300(G) (802.11g) ADSL2+ Router User’s Manual...

  • Page 2: Table Of Contents

    Chapter 1 ....................1 1.1 Introducing the BiPAC 7300(G) ..........1 1.2 Features................. 3 1.3 Applications of the BiPAC 7300(G) ........6 Chapter 2 ....................7 2.1 Important Notes ..............7 2.2 Package Contents ..............7 2.3 The Front LEDs ..............8 2.4 The Rear Ports ..............

  • Page 3: Chapter 1

    Chapter 1 Introduction 1.1 Introducing the BiPAC 7300(G) Thank you for purchasing the BiPAC 7300(G) ADSL2+ Modem/Router by Billion. Your new router is an all-in-one unit that combines an ADSL modem, ADSL router and Ethernet network switch to provide everything you need to get the machines on your network connected to the Internet over an ADSL broadband connection.
  • Page 4 addresses making them invisible to outside users on the Internet, so it is much more difficult for a hacker to target a machine on your network. Second, it can block and redirect certain ports to limit the services that outside users can access. To ensure that games and other Internet applications run properly, you can open specific ports for outside users to access internal services on your network.

  • Page 5: Features

    1.2 Features Express Internet Access – ADSL2/2+ capable The BiPAC 7300(G) complies with ADSL worldwide standards. Supporting downstream rates of 8Mbps with ADSL, the router is capable of up to 12/24 Mbps with ADSL2/2+, and upstream rates of up to 1 Mbps. Users enjoy not only high-speed ADSL services but also broadband multimedia applications such as interactive gaming, video streaming and real-time audio which are easier and faster than ever.
  • Page 6 Firewall NAT technology supports simple firewalls and provides options for blocking access from the Internet, like Telnet, FTP, TFTP, WEB, SNMP and IGMP. Domain Name System Relay Domain Name System (DNS) relay provides an easy way to map a domain name with a user-friendly name such as www.billion.com with an IP address.
  • Page 7 addresses, including subnet masks and DNS IP addresses and distributes them to local computers. This provides an easy way to manage the local IP network. Rich Packet Filtering This feature filters the packet based on IP addresses as well as Port numbers. Filtering packets to and from the Internet provides a higher level of security control.

  • Page 8: Applications Of The Bipac 7300(G)

    1.3 Applications of the BiPAC 7300(G)

  • Page 9: Chapter 2

    Chapter 2 Product Overview 2.1 Important Notes Do not use the router in high humidity or high temperatures. Do not use the same power source for the router as other equipment. Do not open or repair the case yourself. If the router is too hot, turn off the power immediately and have it repaired at a Warning qualified service center.

  • Page 10: The Front Leds

    2.3 The Front LEDs BiPAC 7300 BiPAC 7300G Description PPP : Steady glow when there is a PPPoA / PPPoE connection. Lights when successfully connected to an ADSL DSLAM ADSL: (linesync). Steady glow when connected to an Ethernet device. LAN Port Glows green for 100Mbps;...

  • Page 11: The Rear Ports

    2.4The Rear Ports BiPAC 7300 BiPAC 7300G Port Description Connect the supplied power adapter to this jack. After the router is powered on, press this recessed button using the end of paper clip or other small pointed object to reset the router or to restore it to factory default settings.
  • Page 12 default settings. The login will be reset to admin and the password will be reset to admin, and the modem will be accessible via its default IP address at http://192.168.1.254/ Connect a UTP Ethernet cable (Cat-5 or Cat-5e) to one of the four LAN ports when connecting to a PC or an office/home network of 10Mbps or 100Mbps.

  • Page 13: Cabling

    2.5 Cabling One of the most common causes of problems is bad cabling or ADSL line(s). Make sure that all connected devices are turned on. On the front of the product is a bank of LEDs. Verify that the LAN Link and ADSL line LEDs are lit.

  • Page 14: Chapter 3

    Chapter 3 Installation You can configure the BiPAC 7300(G) router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux, Mac and Windows 98/NT/2000/XP/Me include a web browser as a standard application. 3.1 Before Configuration PCs must have a properly installed Ethernet interface and connect to the router directly or through an external repeater hub.
  • Page 15 Configuring a PC in Windows XP 1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties.
  • Page 16 Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4.
  • Page 17 Configuring PC in Windows 98/Me 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2.Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3.Select the Obtain an IP address automatically radio button.
  • Page 18 Configuring PC in Windows NT4.0 1.Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2.Select TCP/IP Protocol and click Properties. 3.Select the Obtain an IP address from a DHCP server radio button and click OK.

  • Page 19: Factory Default Settings

    3.2 Factory Default Settings Before configuring the BiPAC 7300(G) router, you need to know the following default settings. Web Interface: Username: admin Password: admin LAN Device IP Settings: IP Address: 192.168.1.254 Subnet Mask: 255.255.255.0 ISP setting in WAN site: PPPoE DHCP Server: DHCP server is enabled.

  • Page 20: Lan And Wan Port Addresses

    3.3 LAN and WAN Port Addresses The parameters of LAN and WAN ports are preset at the factory. The default values are shown below. LAN Port WAN Port IP address 192.168.1.254 The PPPoE function is enabled to Subnet Mask 255.255.255.0 automatically get the WAN port Enabled...
  • Page 21 PPPoE With EZSO built-in, you can simply plug cables in as first installation and turn on host computer to surf Internet through WEB browser like IE. You do not need to login into the router and search the router’s WEB GUI configuration page to find out the right web page for configuring your PPPoE/PPPoA credentials.
  • Page 22 PPPoA 1. Please wait when the connection is trying. 2.Enter the username and password provide by your ISP. 3. If login failed, Please input the correct 4. Login Successfully. username and password again.
  • Page 23 DHCP With this method, user does not need to access router to configure it and set lot of parameters. Besides, it eliminates the complicated way to configure the device and will definitely reduce service call from users. 1. Please wait when the connection is trying. 2.

  • Page 24: Chapter 4

    Chapter 4 Configuration Once you have logged on to your BiPAC 7300(G) ADSL2+ Router via your web browser, you can begin to set it up according to your requirements. On the configuration homepage, the left navigation pane links you directly to the setup pages, which include: Status (ARP Table, Wireless Association, Routing Table, DHCP Table, System Log, Security Log) Quick Start...

  • Page 25: Status

    4.1 Status...
  • Page 26 Device Information Host Name: Provide a name for the router for identification purposes. Host Name lets you change the router name. System Up-Time: Records system up-time.
  • Page 27 Current time: Set the current time. See the Time Zone section for more information. Hardware Version: Chipset version Software Version: Firmware version LAN MAC Address: The LAN MAC address WAN MAC Address: The WAN MAC address Home URL: Connects to the Home Website. IP Address: LAN port IP address.

  • Page 28: Arp Table

    4.1.1 ARP Table The router’s ARP (Address Resolution Protocol) Table shows the mapping of Internet (IP) addresses to Ethernet (MAC) addresses. This is a quick way to determine the MAC address of the network interface of your PCs to use with the router’s Firewall – MAC Address Filter function.

  • Page 29: Wireless Association

    4.1.2 Wireless Association IP Address: It is IP Address of wireless client that join this network. MAC: The MAC address of wireless client.

  • Page 30: Routing Table

    4.1.3 Routing Table Routing Table: #: Item number Destination: IP address of the destination network. Netmask: The destination netmask address. Gateway/Interface: IP address of the gateway or existing interface that this route uses. Cost: The cost of transmission for routing purposes. The number need not be precise, but it must be between 0 and 65535.

  • Page 31: Dhcp Table

    4.1.4 DHCP Table Leased: DHCP assigned IP addresses information. IP Address: IP addresses of devices on your LAN (Local Area Network). MAC Address: The MAC Address that you want to assign the fixed IP address Client Host Name: Expired IP addresses information Register Time: Register time information...

  • Page 32: System Log

    4.1.5 System Log Display system logs accumulated up to the present time. You can trace historical information with this function.

  • Page 33: Security Log

    4.1.6 Security Log This screen displays security log information. If a hacker attacks your server, he is isolated by the firewall function and the router records related information. This helps you know where the hacker comes from.

  • Page 34: Quick Start

    4.2 Quick Start For detailed instructions on configuring WAN settings, see the WAN section of this manual. The information you need for the Quick Start wizard to get you online are your login (often in the form of username@ispname), your password, and the encapsulation type. Your ISP can supply all the details you need.
  • Page 35 Connection Encapsulation: Select the encapsulation type your ISP uses or choose “Auto Scan”. Click Start to begin scanning for encapsulation types offered by your ISP. If the scan is successful, you are presented with a list of supported options. VCI: Enter the VCI assigned to you. This field may already be configured. VPI: Enter the VPI assigned to you.
  • Page 36 Optional Setting IP Address: Type your ISP assigned IP address in the IP Address text box. Subnet Mask: Enter a subnet mask in dotted decimal notation. Default Gateway: You must specify a gateway IP address (supplied by your ISP) Obtain DNS automatically: Select this check box to use DNS. Primary DNS: Enter the IP addresses of the DNS servers.

  • Page 37: Configuration

    4.3 Configuration Click this item to access the following sub-items that configure the ADSL router: LAN, WAN, System, Firewall, QoS, Virtual Server and Advanced. These functions are described in the following sections.

  • Page 38: Lan (Local Area Network)

    4.3.1 LAN (Local Area Network) 4.3.1 LAN (Local Area Network) A Local Area Network (LAN) is a shared communication system to which many computers A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a are attached and is limited to the immediate area, usually the same building or floor of a building.
  • Page 39 4.3.1.2 Wireless Mode: 802.11b + g (Mixed mode), 802.11b and 802.11g. The factory default is 802.11b + ESSID: Enter the unique ID given to the Access Point (AP), which is already built-in to the router’s wireless interface. To connect to this device, your wireless clients must have the same ESSID as the device.
  • Page 40 AP. WDS takes advantages of cost saving and flexibility which no extra wireless client device is required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network. In addition, WDS enhances its link connection security in WEP mode, WEP key encryption must be the same for both access points.
  • Page 41 WPA2 Pre-Shared Key WPA2 Algorithms: TKIP (Temporal Key Integrity Protocol) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. WPA2 Shared Key: The key for network authentication The input format is in character style and key size should be in the range between 8 and 63 characters.

  • Page 42: Dhcp Server

    Passphrase: This is used to generate WEP keys automatically based upon the input string and a pre-defined algorithm in WEP64 or WEP128. You can input the same string in both the AP and Client card settings to generate the same WEP keys. Please note that you do not have to enter Key (1-4) as below when the Passphrase is enabled..
  • Page 43 When the DHCP Server is disabled you need to manually assign a fixed IP address to each PC on your network, and set the default gateway for each PC to the IP address of the router (the default is 192.168.1.254). To configure the router’s DHCP Server, check DHCP Server and click Next.
  • Page 44 If you check DHCP Relay Agent and click Next then you must enter the IP address of the DHCP server which assigns an IP address back to the DHCP client in the LAN. Use this function only if advised to do so by your network administrator or ISP. Click Apply to enable this function.

  • Page 45: Wan (Wide Area Network)

    4.3.2 WAN (Wide Area Network) A WAN (Wide Area Network) is an outside connection to another network or the Internet. There are three items within the WAN section: ISP, DNS and ADSL. 4.3.2.1 ISP The factory default is PPPoE. If your ISP uses this access protocol, click Edit to input other parameters as below.
  • Page 46 RFC 1483 Routed Connections Description: Your description of this connection. VPI and VCI: Enter the information provided by your ISP. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account, sharing the single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.
  • Page 47 Description: User-definable name for the connection. VPI/VCI: Enter the information provided by your ISP. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account, sharing a single IP address. If users on your LAN have public IP addresses and can access the Internet directly, the NAT function can be disabled.
  • Page 48 media-specific headers) that the IP attempts to send through the interface. Apply PPPoE Routed Connections PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services using PPP. Description: A user-definable name for this connection. VPI/VCI: Enter the information provided by your ISP. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single ISP account, sharing a single IP address.
  • Page 49 Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”. Password: Enter the password provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive).
  • Page 50 Description: A user-definable name for this connection. VPI/VCI: Enter the information provided by your ISP. Encapsulation method: Select the encapsulation format, this is provided by your ISP. 4.3.2.2 DNS A Domain Name System (DNS) contains a mapping table for domain name and IP addresses.
  • Page 51 as it may provide you with an IP address for their DNS server. You must enter the DNS IP address if you set the DNS Server address on your PC to the LAN IP address of this router. 4.3.2.3 ADSL ADSL Mode: There are four modes “Open Annex Type and Follow DSLAM’s Setting”, ”Annex A”, ”Annex L”, ”Annex M”...

  • Page 52: System

    4.3.3 System There are six items within the System section: Time Zone, Remote Access, Firmware Upgrade, Backup/Restore, Restart and User Management. 4.3.3.1 Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network.
  • Page 53 4.3.3.2 Remote Access To temporarily permit remote administration of the router (i.e. from outside your LAN), select a time period the router permits remote access for and click Enable. You may change other configuration options for the web administration interface using Device Management options in the Advanced section of the GUI.

  • Page 54: Restart Router

    4.3.3.4 Backup / Restore These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes. It is advisable to backup your router’s settings before making any significant changes to your router’s configuration.

  • Page 55: User Management

    If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings. You may also reset your router to factory settings by pressing in the small Reset pinhole button on the back of your router for 10-12 seconds while the router is turned on.
  • Page 56 You can change the user’s password, whether their account is active and Valid, as well as add a comment to each user account. These options are the same when creating a user account, with the exception that once created you cannot change the username. You cannot delete the default admin account;...

  • Page 57: Firewall

    4.3.4 Firewall Firewall and Access Control Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet.
  • Page 58 prevent unauthorized computers or applications accessing your local network from the Internet. Intrusion Detection: Enable Intrusion Detection to detect, prevent, and log malicious attacks. MAC Filter rules: Prevents unauthorized computers accessing the Internet. URL Filter: Blocks PCs on your local network from unwanted websites. A detailed explanation of each of the following five items appears in the Firewall section below: Packet Filter, Ethernet MAC Filter, Wireless MAC Filter, Intrusion Detection, Block WAN Request and URL Filter.

  • Page 59: Packet Filter

    4.3.4.1 Packet Filter Packet filtering enables you to configure your router to block specified internal/external users (IP address) from Internet access, or you can disable specific service requests (Port number) to /from Internet. This configuration program allows you to set up to 6 different filter rules for different users based on their IP addresses or their network Port number.
  • Page 60 Application: User can choose they want. Outgoing Incoming: Determine whether the rule is for outgoing packets or for incoming packets. Active: Choose “Yes” to enable the rule, or choose “No” to disable the rule. Packet Type: Specify the packet type (TCP, UDP, ICMP or any) that the rule applies to. Select TCP if you wish to search for the connection-based application service on the remote server using the port number.
  • Page 61 Schedule time: User can setup the time to use the packet filter. If the DHCP server option is enabled, you must be very careful in assigning IP addresses of a filtered private IP range to avoid conflicts because you do not know which PC in the LAN is assigned which IP address.
  • Page 62 Active: Select Yes from the drop down list box to enable MAC address filtering. Action When Matched: Select “Drop” or “Forward”. Log: Choose “Yes” if you wish to generate logs when the filer rule is applied to a packet. MAC Address: Enter the MAC addresses you wish to manage. Candidates: it automatically detects devices connected to the router through the Ethernet.

  • Page 63: Wireless Mac Filter

    4.3.4.3 Wireless MAC Filter The MAC Address supports up to 30 wireless network machines and helps you to manage your network control to accept traffic from specific authorized machines or to restrict unwanted machine(s) to access your LAN. There are no pre-define MAC Address filter rules; you can add the filter rules to meet your requirements Active: Select Yes from the drop down list box to enable MAC address filtering.
  • Page 64 MAC Address: Enter the MAC addresses you wish to manage. Candidates: it automatically detects devices connected to the router through the Ethernet. 4.3.4.4 Intrusion Detection Check “Enable” if you wish to detect intruders accessing your computer without permission. The router automatically detects and blocks a DoS (Denial of Service) attack if a user enables this function.

  • Page 65: Url Filter

    4.3.4.6 URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.billion.com http://www.example.com) filter rules allow you to prevent users on your network from accessing particular websites from their URL. There are no pre-defined URL filter rules; you can add filter rules to meet your requirements.
  • Page 66 Always Block: Select to always check URL filter rules (i.e. at all hours of the day). Block from: Specify the time period to check URL filter rules (e.g. during work hours). Keywords Filtering: Allows blocking by specific keywords within a particular URL rather than having to specify a complete URL (e.g.
  • Page 67 Restrict URL Features Block Java Applet: Blocks Web content which includes the Java Applet to prevent someone who wants to damage your system via the standard HTTP protocol. Block ActiveX: Blocks ActiveX Block Cookies: Blocks Cookies Block Proxy: Blocks Proxy...

  • Page 68: Qos (Quality Of Service)

    4.3.5 QoS (Quality of Service) Quality of Service Introduction If you’ve ever found your ‘net’ speed has slowed to a crawl because another family member is using a P2P file sharing program, you’ll understand why the Quality of Service features in Billion’s routers is such a breakthrough for home users and office users.
  • Page 69 Application: A name that identifies an existing policy. Time Schedule: Scheduling your QOS policy to be applied. Direction: The traffic flow direction to be controlled by the QOS policy. There are two settings to be provided in the Router: LAN to WAN: You want to control the traffic flow from the local network to the outside world.
  • Page 70 configuration. If you want to make the change persistent in flash, choose in the left windows to save it into flash. When you press buttons described above, the following page will show up in your browser. You can use it to define a QOS policy. Controlled Traffic Flow: Specify the traffic flow you want to control.
  • Page 71 GRE: For PPTP VPN Connections. Assigned Data rate: Assign the data ratio for this policy to be controlled. For examples, we want to only allow 20% of the total data transfer rate for the LAN-to-WAN direction to be used for FTP server. Then we can specify here with data ratio = 20. If you have ADSL LINE with 256K/bps.rate, the estimated data rate, in kbps, for this rule is 20%*256*0.9 = 46kbps.
  • Page 72 Best Effort Best Effort (000000) Premium Express Forwarding (101110) Gold service (L) Class 1, Gold (001010) Gold service (M) Class 1, Silver (001100) Gold service (H) Class 1, Bronze (001110) Silver service (L) Class 2, Gold (010010) Silver service (M) Class 2, Silver (010100) Silver service (H) Class 2, Bronze (010110)

  • Page 73: Connection Diagram

    QOS example for your Network Connection Diagram VoIP HTTP web browsing users FTP Server ADSL Subscription Rate Upstream: 256 kbps Downstream: 2048 Mbps Example QOS Plan Application IP or Ports Control Flow Data Rate Time Schedule VoIP User 192.168.0.1 Outgoing Minimal 20% with high priority Always for non-used bandwidth with...
  • Page 74 Example QOS Setup VoIP application Voice is latency-sensitive application. Most VoIP devices are use SIP protocol and the port number will be assigned by SIP module automatically. Better to use fixed IP address for catching VoIP packets as high priority.
  • Page 75 Above settings will help to improve quality of your VoIP service when traffic is full loading.
  • Page 76 FTP Server Application Some of companies will setup FTP server for customer downloading or home user sharing their files by using FTP. LAN to WAN direction:...
  • Page 77 WAN to LAN direction: With above settings that help to limit utilization of upstream of FTP. Time schedule also help you to only limit utilization at day time.
  • Page 78 HTTP Web Browsing You can control the internet web browsing by specify the HTTP 80 (8080 for some proxy server). LAN to WAN direction:...
  • Page 79 WAN to LAN direction:...

  • Page 80: Virtual Server

    4.3.6 Virtual Server In TCP/IP and UDP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that are pre-assigned to them by the IANA (the Internet Assigned Numbers Authority), and these are referred to as “well-known ports”.
  • Page 81 Well-known and Registered Ports Port Number Protocol Description FTP Data FTP Control TCP & UDP SSH Remote Login Protocol Telnet SMTP (Simple Mail Transfer Protocol) TCP & UDP DNS (Domain Name Server) TFTP (Trivial File Transfer Protocol) World Wide Web HTTP POP3 (Post Office Protocol Version 3) NEWS (Network News Transfer Protocol) NTP (Network Time Protocol)
  • Page 82 Delete: Check the Rule No. you wish to delete, then click “Delete”. Item: Item number Service select: Select the service you wish to configure Protocol: Automatic when you choose Service select Start Port & End Port: Enter the public port number & range you wish to configure. IP Address: Enter the IP address of a specific internal server to which requests from the specified port is forwarded.
  • Page 83 In addition to specifying the port number used, you also need to specify the protocol used. The protocol is determined by the particular application. Most applications use TCP or UDP, however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all”...

  • Page 84: Advanced

    4.3.7 Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their router, unless advised to do so by support staff.
  • Page 85 address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP. You first need to register and establish an account with the Dynamic DNS provider using their website, for example http://www.dyndns.org/ There are more than 5 DDNS services supported.
  • Page 86 VLAN Group Name: There are eight groups that user can setup by themselves. VLAN ID: Group name ID LAN Tagging: Tagging VLAN ID to the specific VLAN group for Ethernet interface. Ethernet port: Port name of Router Link VLAN Group to WAN connection Interface: Select the WAN connection interface that VLAN group link.
  • Page 87 2. After checking the box to enable VLAN function, you will check the table according to the needs as show below.
  • Page 88 4.3.7.4 Device Management The Device Management advanced configuration settings allow you to control your router’s security options and device monitoring features. Embedded Web Server: HTTP Port: The port number of the router’s embedded web server (for web-based configuration uses. The default value is the standard HTTP port, 80. You may specify an alternative if, for example, you are running a web server on a PC within your LAN.
  • Page 89 removing the need for the user to control advanced configuration of their device. Both the user’s Operating System and the relevant application must support UPnP in addition to the router. Windows XP and Windows Me natively support UPnP (when the component is installed), and Windows 98 users may install the Internet Connection Sharing client from Windows XP in order to support UPnP.
  • Page 90 The following MIBs are supported: From RFC 1213 (MIB-II): System group Interfaces group Address Translation group IP group ICMP group TCP group UDP group EGP (not applicable) Transmission SNMP group From RFC1650 (EtherLike-MIB): dot3Stats From RFC 1493 (Bridge MIB): dot1dBase group dot1dTp group dot1dStp group (if configured as spanning tree) From RFC 1471 (PPP/LCP MIB):...
  • Page 91 PPP IP Group From RFC 1474 (PPP/Bridge MIB): PPP Bridge Group From RFC1573 (IfMIB): ifMIBObjects Group From RFC1695 (atmMIB): atmMIBObjects From RFC 1907 (SNMPv2): only snmpSetSerialNo OID Universal Plug and Play (UPnP): UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices.
  • Page 92 Installing UPnP in Windows Example Follow the steps below to install the UPnP in Windows Me. Step 1: Click Start and Control Panel. Double-click Add/Remove Programs. Step 2: Click on the Windows Setup tab and select Communication in the Components selection box.
  • Page 93 Step 4: Click OK to go back to the Add/Remove Programs Properties window. Click Next. Step 5: Restart the computer when prompted. Follow the steps below to install the UPnP in Windows XP. Step 1: Click Start and Control Panel. Step 2: Double-click Network Connections.
  • Page 94 Step 5: In the Networking Services window, select the Universal Plug and Play check box. Step 6: Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. Auto-discover Your UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway.
  • Page 95 Step 2: Right-click the icon and select Properties. Step 3: In the Internet Connection Properties window, click Settings to see the port mappings that were automatically created. Step 4: You may edit or delete the port mappings or click Add to manually add port mappings.
  • Page 96 Step 5: Select Show icon in notification area when connected option and click OK. An icon displays in the system tray Step 6: Double-click on the icon to display your current Internet connection status. Web Configurator Easy Access With UPnP, you can access web-based configuration for the BiPAC 7300(G) without first finding out the IP address of the router.
  • Page 97 Follow the steps below to access web configuration. Step 1: Click Start and then Control Panel. Step 2: Double-click Network Connections. Step 3: Select My Network Places under Other Places. Step 4: An icon describing each UPnP-enabled device shows under Local Network. Step 5: Right-click on the icon of your BiPAC 7300(G) and select Invoke.
  • Page 98 decisions. Default is set to Enable 4.3.7.6 WAN IP Change Alert Send a log via Email When WAN IP is changed. Default is set to Disable.

  • Page 99: Save Configuration To Flash

    4.4 Save Configuration to Flash After changing the router’s configuration settings, you must save all of the configuration parameters to FLASH to avoid losing them after turning off or resetting your router. Click Save to write your new configuration to FLASH.

  • Page 100: Restart

    4.5 Restart Click Restart with option Current Settings to reboot your router (and restore your last saved configuration). If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings.

  • Page 101: Chapter 5

    Chapter 5 Troubleshooting If your ADSL Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider or Billion support. This can save you time and effort but if symptoms persist, consult your service provider. Problems starting up the router Problem Corrective Action...

  • Page 102: Problems With The Lan Interface

    Frequent loss of Ensure that all other devices connected to the same ADSL linesync telephone line as your router (e.g. telephones, fax machines, (disconnections). analogue modems) have a line filter connected between them and the wall socket (unless you are using a Central Splitter or Central Filter installed by a qualified and licensed electrician), and ensure that all line filters are correctly installed and the right way around.

  • Page 103: Appendix

    Appendix Support and Contact Information If you cannot resolve the problem after reading the Troubleshooting chapter, please contact the dealer where you purchased this product. Contact Billion AUSTRALIA http://www.billion.com.au ©2006 Billion Electric Co., Ltd. PC Range P/L. All Rights Reserved. WORLDWIDE http://www.billion.com...

This manual is also suitable for:

Bipac 7300

Table of Contents