Summary of Contents for Barco B-10 Mobile LED R9855510
Page 1
B-10 Mobile LED Installation & maintenance manual R9855510 R5976956/03 19/06/2007...
Page 2
Barco nv Events Noordlaan 5, B-8520 Kuurne Phone: +32 56.36.89.70 Fax: +32 56.36.88.24 E-mail: sales.events@barco.com Visit us at the web: www.barco.com Printed in Belgium...
Page 3
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
B-10 Mobile LED. Barco recommends inspections at regular intervals for the B-10 Mobile LED. If a part of the B-10 Mobile LED is found to have damage, it must be removed for service or replaced immediately.
1. Safety instructions Important Safety instructions Instructions: • Read these instructions. • Keep these instructions. • Heed all warnings. • Follow all instructions. • IMPORTANT, plug holder clamps must be locked firmly on all controller units and power boxes to prevent the possible ingress of fluids or solid particles.
1. Safety instructions Important Warnings Important warnings • High leakage current: The combination of multiple tiles in an installation results in increased levels of leakage current. In order to avoid risk of electric shock due to high leakage current, proper grounding of the installation is required. •...
Page 10
1. Safety instructions What is a faulty operation • Levelling the trailer by first placing the rear stabilizers. This way almost the half of the weight of the total trailer (1800 Kg) rests on the jockey wheel. Image 1-1 Wrong way to level trailer •...
Page 11
1. Safety instructions The good way of working, building off the vehicle • Retract the rear stabilizers first and then the front stabilizers till none of them touch the ground. • Turn the jockey wheel downwards till the wheel touches the ground. Do not lift the trailer at the front side ! •...
Page 12
1. Safety instructions R5976956 B-10 MOBILE LED 19/06/2007...
There is no need for trusses and structures to be set up. The screen can be turned around 360 degrees, allowing you to adjust the display to face the audience. The B-10 Mobile LED contains a diesel-fueled generator. No external power supply is required, and it comes with a Barco LED-PRO or D320 Digitizer for high quality image processing.
2. System Overview Image 2-2 All tiles are connected in series via a data path. Each tile picks out a part of the video information of the data stream on the data path and processes this information for displaying on its LED’s. 2.2.2 SLite 10 XP specifications Specifications...
2. System Overview D320 input compatibility S-Video, Composite, YUV, RGB, SDI, HDSDI, Data DVI up to UXGA Certifications ETL, CE, CEBEC, TUV, FCC class A Tile dimensions width: 896mm (35.3") height: 672mm (26.5") depth: 248mm (9.8") Order Information R9004170 2.2.3 Dimensions SLite XP tile SLite XP tile dimensions Image 2-3...
Data input port. Data output port. AUTION The SLite input/output ports can only be used in conjunction with Barco’s outdoor cables for LED- walls. Do not use any other cables then those specified. AUTION Dummy plugs must be placed on unused connection ports of the connection module and all plug holder clamps must be locked firmly.
• DVI-I connectors support both universal analog and DVI input with loop-through. • DVI output connector for Barco LED Display interface. • Input Video detection and Auto-acquisition. LED-PRO will auto detect and match input video to stored formats or user configurations.
2. System Overview 2.4.2 Dimensions Overview 3584 4240 Image 2-7 Dimensions B-10 Mobile LED generator 2.5.1 Introduction Overview Please read this section carefully before using the generator. If you act as stated in this section, your generating set will guarantee you a smooth functioning time after time.
2. System Overview 2.5.3 Control panel Description Image 2-9 Control panel The control panel of the EPS8DE consists of: • Starting key (off / on / glow / start) • Pilot lamp green (contact on / off), lamp lights up when contact on •...
2. System Overview On the inside of the control panel there can be found: • 2 x relay 12V/30A for guarding oil pressure and temperature of cooling liquid with aid of a stopping coil (Engine shuts off when the oil pressure is low or the temperature of the cooling liquid is to high). •...
2. System Overview Image 2-13 Identification 2. In case of overload, the thermal-magnetic protection in the control panel shall be switched off after a short period of time. Check the load, reduce it if necessary and switch on the thermal-magnetic protection again. 3.
3. Setup of the B-10 Mobile LED 3. SETUP OF THE B-10 MOBILE LED Overview • Installation of the B-10 Mobile LED • Powering the B-10 Mobile LED • Extending the LED display • Rotating the LED display • Move down the LED Display •...
3. Setup of the B-10 Mobile LED Image 3-2 Contact key and power cable of pump 2. After several seconds turn-on the generator with this contact key. Caution: The generator of the B-10 Mobile LED needs to be well-ventilated. Therefore, the generator of the B-10 Mobile LED is not indented to run for a long period of time with the roof closed.
Page 27
3. Setup of the B-10 Mobile LED Image 3-3 Pump system 2. Push on the black button. 3. Lift the first halve of the LED-wall by using the lever Lift this part of the display up till its 10 cm above the deck of the B-10 Mobile LED. Fastening both display halves together 1.
3. Setup of the B-10 Mobile LED Image 3-5 Safety pieces Caution: Make sure the safety pins are placed in the mast. This is mandatory for security reason and to avoid that the mast comes slightly down after closing the pump system. 3.
3. Setup of the B-10 Mobile LED How to move down? Lift down the display till it’s on the bottom. Note: Do not forget to take away the safety pieces from the mast. Caution: Watch out that cables are not under the display. 2.
Page 30
3. Setup of the B-10 Mobile LED R5976956 B-10 MOBILE LED 19/06/2007...
4. Maintenance, Service 4. MAINTENANCE, SERVICE Overview For maintenance, service and repair on the B-10 Mobile LED please consult qualified service technicians/personnel. Servicing is required when the B-10 Mobile LED has been damaged in any way, such as hydraulic mast or generator is damaged, the B-10 Mobile LED does not operate normally.
Page 32
4. Maintenance, Service Daily 500 km Quarterly Yearly Light cover Outriggers Functioning Attachment Frame Transverse at side section support for girders girders of mast Transverse at compressor Splashguards Trailor enclosure Doors Lock system (inside) Functioning doors Door frame Functioning lock Rubber of door frame Door stops Door hinges...
4. Maintenance, Service Daily 500 km Quarterly Yearly cylinder flexible attachment to grid Generator motor general alternator gas - diesel exhausts fixing state C = Control L = Lubricate T = Tighten Cl = Clean After 50h00 the diesel generator needs to get its first maintenance. Please refer to the Kubota and Leroy Somer manuals as well as section 4.2 for more information on maintenance of the generator.
Page 34
4. Maintenance, Service Service intervals For a detailed explanation of the service intervals, consult the service and maintenance manual of the generator. Interval Items Every 50 hours • Check of fuel pipes and clamp bands After first 50 hours Change of engine oil Every 100 hours Cleaning of air cleaner element Cleaning of fuel filter...
Page 35
4. Maintenance, Service Overview service center For Europe Country Engine (Kubota) Alternator (Leroy Somer) Austria MAG Motoren GmbH L-S Elektroantriebe GmbH A-5023 Salzburg A-1180 Wien Tel. 43.662640460 Tel. 43.2224706401 Fax. 43.662882340 Fax. 43.222479225 Belgium Matermaco S.A. Leroy Somer Belgium 1030 Brussel - Bruxelles 2800 Mechelen Tel.
Page 36
4. Maintenance, Service Country Engine (Kubota) Alternator (Leroy Somer) Malta Gaetano Caruana Limited Zebbug, MALTA G.C. Tel. 356.460881 Fax. 356.465824 Netherlands Gebr. Prins B.V. Leroy Somer Nederland 2676 BD Maasdijk 3769 Bt-Soesterberg Tel. 31.174516240 Tel. 31.346353244 Fax. 31.174518142 Fax. 31.346352284 Norway Univ.
Page 37
4. Maintenance, Service Country Engine (Kubota) Alternator (Leroy Somer) Brazil Polus Maquina Eletricas Campuci Sao Paulo CEP 01524 Tel. 55.11.9148766 Chili Clemsa Moteurs Leroy Somer Maipu/Santiago Santiago Tel. 56.2.5572970 Tel. 56.2.497314 Fax. 56.2.5571439 Fax. 56.2.497314 Columbia Fevacol Bogota Tel. 57.1.2856697 Fax.
Page 38
4. Maintenance, Service Country Engine (Kubota) Alternator (Leroy Somer) Israel FK Generators & Equipm. Moteurs Leroy-Somer Ind. Z. Holon PB 1729 Tel Aviv 66089 Tel. 972.3.5570567 Tel. 972.3.820996 Fax. 972.3.5560771 Fax. 972.3.820040 Japan Kubota Osaka Head Off. Moteurs Leroy-Somer Osaka 556-8601 Tokyo 101 Tel.
Page 39
4. Maintenance, Service Country Engine (Kubota) Alternator (Leroy Somer) Turkey Altinboga SASIM Kemeralti Istanbul 80020 Karaköy-Istanbul Tel. 90.212.5013465 Tel. 90.1.1515626 Fax. 90.212.6122381 Fax. 90.1.1515524 Un. Arab Emirates M. Tayyeb Khoory & Sons Moteurs Leroy Somer P.O.Box 4664 Dubai Ab-Dhabi Tel. 971.4.223251 Tel.
Page 40
4. Maintenance, Service Country Engine (Kubota) Alternator (Leroy Somer) Guinea Les ateliers de Guinee Conakry Tel. 224.464744 Ivory Coast Sorepel Abidjan 01 Tel. 225.359525 Fax. 225.350414 Morocco Cogepra L-S Maroc 20300 Casablanca Casablanca Tel. 212.2.307436 Tel. 212.354956 Fax. 212.2.302307 Fax. 212.354956 South Africa Terraquip Kempton Park 1620...