Table of Contents
Advertisement
On-Screen
Display
Menu
Power
control setting
allows you to save energy.
Example I _
PowerControl
1 Press MENU
to display
the MENU screen,
and then
press _/_,
to select "Power Control".
2
Press A/_'
to select a "No Signal Off" or "No
Operation
Off", and then press ENTER.
3
Press _/_-
to select "Enable",
and then press
ENTER.
4
Press MENU
to exR.
When set to"Enable",
the power
wHI automatically
shut
down
r_there is no signal for 15 minutes.
Five minutes before the power shuts down, the remaining
time displays every minute.
"Disable" is the factory preset value.
When a TV program finishes, this function may not operate
When set to "Enable",
the power will automatically
shut
down
if there is no operation
for 3 hours.
• Five minutes before the power shuts down, the remaining
time displays every minute
• "Disable" is the factory preset value
Example
[ _
Setup
1 Press MENU
to display
the MENU screen,
and then
press 4/_
to select "Setup".
2
Press A/_'
to select a specific
adjustment
item,
and then
press ENTER.
• When you select "EZ Setup", "OH Setup", "Parental
CTRL" and "Reset", you can enter the 4 digit secret
number here See page 21 for setting a secret number.
3
Press A/_'
(or 4/_)to
select the desired
setting,
and then press ENTER.
4
Press MENU
to exit.
You can run EZ Setup again, even alter setting
up the
preset channels.
Language:
Select from among 3 languages (English,
French and Spanish)¸
TV Location:
Select "Home" or "Store" for the location
where you plan to install the %/
Ifyou select "Home", AV MODEis set to "STANDARD"
Ifyou select "Store", AVMODE is setto "DYNAMIC(Fixed)"
Incase no remotecontrol signal is receivedwithin 30
minutes, AVMODE will change to "DYNAMIC(Fixed)"
automatica%
Air/Cable:
Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable"
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area¸
See "Initial Setup" on page 11 for setting each item.
If no channel isfound, confirm the type of connection made
with your TV and try E7 Setup again¸
Ifyou select "Analog Search Start" and initiate the channel
search, the OH Memory for Cable Digital will be deleted
If initial setup does not memorize
all the channels
in
your region, follow the instructions
below to manually
memorize
the channels.
Air/Cable:
Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable"
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area
CH Memory:
You can sdect the channels to skip in each
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and
DIGITAL (Cable)
On: Skips channels [Channelselection disabledusing ON
A/V)
Off: Doesnot skipchannels (Channelselection enabledusing
CHA/V)
See "Initial Setup" on page 11 for setting each item.
If no channel isfound, confirm the type of connection made
with your TV and try channel search again.
Ifyou select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
In order to receive digital air broadcasts,
you need
a digital broadcast
antenna.
You can confirm
the
antenna
configuration
through
the "Antenna
Setup
DIGITAL"
screen.
If necessary,
adjust the direction
of
the antenna to obtain the maximum
signal strength.
Signal Strength:
The signal strength of DIGITAL channel
is displayed. The signal information is based on the
current channel
Channel
Strength:
Input the 2-digit channel number
to check the signal strength of the selected channel
Make sure the signal is strong enough for each
channel
This function isavailablefor DIGITAL (AIr)only
19
Hide quick links:
Advertisement
Table of Contents
