Hdmi Auto View - Sharp Aquos LC-32D47UA Operation Manual

On-Screen Display Menu
Position
For adjusting a picture's horizontal and vertical
position.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: Centers the image by moving it up or down.
• For resetting adjustments to the factory preset values, press
AI,.
to select "Reset", and then press ENTER.
• When connecting a PC to the HOMI terminal, the image
position will be automatically adjusted. It cannot be
manually adjusted.
• Adjustments are stored separately according to input
source.
• When a OlV channel is selected, the horizontal position
cannot be adjusted.
• The horizontal and/or vertical position may not be able to
be adjusted or it may be adjusted only to a certain degree.
PC
Setup
Some input signals may have to be registered manually
to display properly. The pair of input signals (resolutions)
in the list below is not distinguishable when received.
In such a case, you have
to
set the correct signal
manually. After setting once, it will display when the
same signal (resolution) is input again.
11024
x
768 1360
x
768
I
• You can only select the "Input Signal" on the Setup menu
when receiving one of the 2 input signals listed above.
For automatically adjusting the PC image.
Yes: Auto Sync. starts.
No: This function does not work.
• When Auto Sync. is successful, "Completed" displays. If
not, Auto Sync. failed.
• Auto Sync. may fail even if "Completed" displays.
• Auto Sync. may fail if the computer image has low
resolution, has unclear (black) edges, or is
moved
while
executing Auto Sync.
• Be sure to connect the PC to the lV and switch it on before
starting Auto Sync.
21
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimize the image.
H-Pos.: Centers the image by moving it to the left or
right.
V-Pos.: centers the image by moving it up or down.
Clock: Adjust when the image flickers with vertical
stripes.
Phase: Adjust when characters have low contrast or
when the image flickers.
• For resetting all Fine Sync. adjustment items to the factory
preset values, press
AI,.
to select "Reset", and then press
ENTER.
• It is not necessary to adjust the "Clock" or "Phase" when a
digital signal is being input, so it cannot be selected.
• The default cursor position may not be in the center,
because the screen position variable ranges may be
asymmetrical.
PC
Audio Select
Determines whether the AUDIO terminal is used for
INPUT 4 (PC-IN) or INPUT 5 (HDMI).
Input 4 (PC): Select this item when the audio signal is
input
via
the INPUT 4 (PC-IN) terminal using an analog
RGBcable.
Input 5 {HOMI): Select this item when the audio signal is
input
via
the INPUT 5 (HOMI) terminal using an HOMI-
OVI conversion cable.
• When "PC Audio Select" is set to "Input 5 (HOM!)", sound
will not be produced if you use only an HOMI-certified
cable to connect HOMI-compatible equipment. To produce
sound, you should make an analog audio connection.
• If you want to connect HOMI-compatible equipment using
only an HOMI-certified cable, set "PC Audio Select" to
"Input 4 (PC)".
HDMI Auto View
To watch an HDMI or PC-IN equipment image,
select "INPUT5", "INPUT6" or "INPUTl" from "INPUT
SOURCE" menu using INPUT on the remote control
unit or on the lV.
Enable: To use View Mode based on signal recognition,
including an HOMI signal.
Disable: No function.
• Refer to your external equipment operation manual for the
signal type.
• When connecting an HOMI-OVI conversion adapterlcable
to the HOMI terminal, the image may not come in clearly.