Intel S5520SC - Workstation Board Motherboard Quick Start Manual

Intel® Workstation Board S5520SC
Quick Start User's Guide
Thank you for buying the Intel® Workstation Board
S5520SC. The following information will help you
integrate your new server board into a server
chassis. The Intel® Workstation Board S5520SC
is designed for use with the Intel® Server
Chassis SC5600Base and the Intel® Server
Chassis SC5650WS.
For details on these chassis or to select a third-party
chassis, please visit:
http://support.intel.com/support/motherboards/server.
When installing the server board into a reference chassis,
refer to the reference chassis instructions.
Service Guides are also available on the CDs that accompanied
your Intel® Workstation Board S5520SC.
If you are not familiar with ESD (Electrostatic Discharge) procedures
used during system integration, please see the Intel® Workstation Board S5520SC
Service Guide, available on the Intel® Server Deployment Toolkit 3.0 CD or at
http://support.intel.com/support/motherboards/server/S5520SC/manual.htm
4
Warning
Install the Workstation Board
Read all caution and safety
statements in this document
IMPORTANT NOTE: If you are using a
before performing any of the non-Intel server chassis, see your
instructions. Also see the Intel ® chassis documentation for preparatory
steps prior to server board installation.
Server Board and Server Chassis
Safety Information document at:
A. Insert Workstation Board
http://support.intel.com/support/
Place the board into the chassis, making
motherboards/server/sb/cs-010770
sure that back panel I/O openings and
.htm for complete safety information.
chassis standoffs align correctly.
• When using the Intel ® Server Chassis
Warning
SC5600Base, remove the rear chassis fan
and then insert the I/O connector
side (back) of the board first.
Installation and service of
• When using the Intel
this product should only be ®
Server Chassis SC5650WS,
performed by qualified service
remove the front drive bay
personnel to avoid risk of injury from
and rear chassis fan, and then
electrical shock or energy hazard.
insert the front of the board first.
Slide the board back so the I/O
connectors fit through the I/O shield.
Caution
Observe normal ESD
5
b
[Electrostatic Discharge]
procedures during system
Install the Processor(s) ... continued
integration to avoid possible
damage to server board and/or
D. Install the Processor
other components.
Tools Required
CAUTION: The underside
of the processor has
components that may damage
the socket wires if installed
improperly.
#2 Phillips*
Anti-static
screwdriver wrist strap
Components
Intel is a registered trademark of Intel Corporation or its
Processor must align
subsidiaries in the United States and other countries.
correctly with the
*Other names and brands may be claimed as the property
of others. Copyright © 2011, Intel Corporation. All rights socket opening
reserved.
before installation.
DO NOT DROP processor
E39546-009
into the socket!
B. Attach the Workstation Board
Intel ® Server Chassis
SC5600Base Shown
The Intel Server Chassis SC5600Base and the Intel
®
to attach the workstation board to the chassis. Use the screws indicated for your chassis.
For a non-Intel server chassis, use the fasteners that came with your chassis.
• Intel Server Chassis SC5600Base: Attach the
®
board to the chassis at the nine locations indicated
by the solid blue arrows in the figure [ ] and at
the one location indicated by the solid red arrow [ ].
Intel Server Chassis
®
• Intel Server Chassis SC5650WS: Push down
®
SC5650WS Shown
firmly to engage the snap-top standoffs at the
location indicated by the solid red arrow [ ].
Front
Edge of Use screws to attach the board to the chassis at
Board
the nine locations indicated by the solid blue
arrows [ ].
Intel Server Intel Server
® ®
Chassis Chassis
SC5600Base SC5650WS
E. Close Load Plate and Socket Lever
A A
Orient the processor with the socket Close the
so that the orientation notches on load plate
the processor align with the two all the A
orientation posts on the socket. way as
shown.
Install the processor as shown.
Orientation Notches
B
Close the socket lever.
C
Remove the protective cover after it been
automatically disengaged from the load plate.
A
B
C
Orientation Posts
Minimum Hardware Requirements
To avoid integration difficulties and possible board damage,
your system must meet the following minimum requirements:
• Processor: Minimum of one Intel
or one Intel Xeon Processor 5600 Series.
•
Supports maximum 95 watt processor in the Intel
Chassis SC5600Base.
• Supports maximum 130 watt processor in the Intel
Chassis SC5650WS.
• Heat Sink(s): Minimum of one active heat sink for the Intel
Server Chassis SC5600Base and SC5650WS.
• Memory Type: Minimum of one 1 GB, 240-pin,
RDIMM or UDIMM, DDR3-800, DDR3-1066, or DDR3-1333.
• AC Power: SSI EPS 12V compliant power supply.
Recommended minimum of 670 Watts with 3 A of standby
current, or calculate your system power demand with the power
budget tool.
For a complete list of compatible processors, heat sinks, and memory, see:
http://support.intel.com/support/motherboards/server/s5520SC/
In the Intel ®
CAUTION: Server Chassis
SC5600Base
Supported Maximum 95
watt processor
Processor
Supported One maximum
Graphics Card 150 watt graphics
card in PCI
Express* Slot 6
NOTE: Graphics cards with power greater than 75 W must be self-cooled
with exhaust out the back of the chassis.
3
Install Workstation
Board Bumpers
NOTE: If you are using an Intel Server Chassis you must install the chassis
®
bumpers included with the chassis. Refer to your Intel
and Intel Server Chassis Quick-Start User's Guide for proper bumper
®
installation guidelines. If you are using a non-Intel server chassis that
includes bumpers, refer to the non-Intel server chassis documentation for
the correct bumper installation procedure. If the non-Intel server chassis
does not include bumpers, then you should consult with the chassis vendor
to determine whether bumpers are required or not.
Prepare Workstation Board
A
Rotate board to show underside and hold upright
as shown.
CAUTION: To avoid damage to the board,
do not lay flat with the component side down.
B
Locate the five circles as shown.
5
a
Install the Processor(s)
Server Chassis SC5650WS use different screws
®
Cautions:
1. When opening a socket, DO NOT TOUCH
the gold socket wires.
2. When unpacking a processor, hold by the
edges only to avoid touching the gold
contact wires.
CPU 1 Socket
CPU 2 Socket
6
Make Workstation Board Power Connections
A
Attach auxiliary power signal
connector to the workstation board.
B
Attach the CPU 1 power connector
to the workstation board. Main Power
Connector Detail
C
Attach the CPU 2 power connector
to the workstation board.
D
Attach the main power connector to
the workstation board.
CAUTION:
Note the location of the latch on each
power cable connector and align it with the D
matching tab on each workstation board socket.
IMPORTANT NOTE: If you are using a non-Intel
server chassis with an ATX power supply, see
the documentation that came with your chassis
for installation information.
1 2
Preparing
the Chassis
Prepare the I/O shield
Xeon Processor 5500 Series
® ®
Do not remove the three circular
knockouts that are at the edge next to
® Server
the openings for the NIC, USB, Serial A,
Observe normal ESD
and 1394 ports. Use caution so you do
® Server
(Electrostatic Discharge)
not deform the shield.
procedures.
®
Attach the Labels to the I/O Shield
Place your
Intel
® Server
Note: Make sure you install the labels
Chassis on a flat anti-static
on the correct side of the I/O shield.
surface to perform the
Note the orientation of the cutouts in
following integration
the drawing before attaching your labels.
procedures. Observe ESD
procedures before A
reaching inside to make
server board connections
or install components.
B
In the Intel ®
Server Chassis Install the I/O
SC5650WS
shield
Maximum 130 watt processor
Shield installs from inside
ONE maximum 300 watt graphics card in
of chassis. The labels
PCI Express* Slot 6 or TWO maximum
150 watt graphics cards. Empty PCI should be visible from the
Express* Slot 3 when a graphics card is
outside of the chassis.
installed in PCI Express* slot 4.
A
B
Workstation Board
®
Attach the Bumpers
C
Remove the backing from each bumper.
D
Press a bumper onto each of the five circles.
B
C
A. Open the Socket Lever
A
Push the lever handle down
and away from the socket to
release it.
B
Rotate the lever open all
the way.
A
B
B
CPU Power
Connector Detail
Auxiliary Signal
Power Detail
CPU 1 Socket
A
Latch
Tab
C
CPU 2 Socket
Installing the I/O Shield and Attach I/O Labels
Labels on outside
face of I/O shield
Diag Line
nos tic In NIC 1
LED s Seri al A USB
Remove the backing from the I/O MSB USB 2
3 NIC 2
LSB USB
USB 0
1394 1
shield labels included with your
ID
MIC In
server board.
Press each label onto the I/O
shield as shown.
Intel ® Server Chassis
SC5650WS shown
Chassis Back
Panel Opening
Insert one side edge of
shield as shown.
B
Push shield firmly into
A
chassis opening until
it clicks into place.
D
B. Open the Load Plate C. Remove the
Processor
A
Push the rear tab with your
Protective Cover
finger tip to bring the front
end of the load plate
up slightly.
A
A
Take the processor out
of the box and remove
the protective shipping
cover.
B
Open the load plate as shown.
A
B
Go to Side 2