HP 22-in-1 Media Card Reader
Introduction
This document describes how to install the HP 22-in-1 Media Card Reader into an HP Workstations
adapter bracket, and then install the media card reader and bracket into an HP computer. Basic
troubleshooting information for the HP 22-in-1 Media Card Reader is also included.
3.5-inch media card reader with integrated USB cable
HP Workstations adapter for 5.25-inch drive bays
Four M3 guide screws
Documentation CD
Warranty information
ENWW
© 2009, 2010 Hewlett-Packard Development Company, L.P.
Microsoft, Windows, and Windows Vista are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
Introduction
1

Advertising

   Related Manuals for HP Z400 - Workstation

   Summary of Contents for HP Z400 - Workstation

  • Page 1: Kit Contents

    Four M3 guide screws ● Documentation CD ● Warranty information © 2009, 2010 Hewlett-Packard Development Company, L.P. Microsoft, Windows, and Windows Vista are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. ENWW Introduction...

  • Page 2: Warnings And Cautions

    Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, enable the surface to cool before touching. WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard.

  • Page 3: Installing The Media Card Reader

    Installing the media card reader Installing the 5.25-inch bay adapter To install the 3.5-inch media card reader into a 5.25-inch drive bay, you must first install the reader into the 5.25-inch bay adapter. If installing the media reader in an HP Z200 or Z400 Workstation, install four black M3 guide screws in the four lower holes of the bay adapter.

  • Page 4: Preparing The Computer, Accessing The Internal Components Of The Computer, Removing Components

    The green carrier latch (5) snaps into place when fully seated. Figure 3 Installing the media reader in the bay adapter Preparing the computer NOTE: Computer models vary. All illustrations are examples only. Accessing the internal components of the computer If you need help preparing the computer for this installation, consult the removal and replacement procedures in the service guide for your computer at http://www.hp.com/support/...

  • Page 5

    Installing the media card reader in the computer Install the media card reader into an optical drive bay. Ensure that the adapter snaps securely into place. Figure 4 Installing the media card reader in the optical bay Connecting the media card reader NOTE: See the service label on the side access panel to locate connectors on the system board.

  • Page 6: Reassembling The Computer, Front Panel Components

    Reassembling the computer To reassemble the computer after installation: Reinstall the card support, if removed. Reinstall the airflow guide, if removed. Reinstall the side access panel. Reconnect power to the computer and all external devices. Restore power to the computer and all external devices. Identifying media slots Front panel components The media slots accept the following cards:...

  • Page 7: Troubleshooting, Solving Common Problems

    Slot ID Media ● CompactFlash Card Type I ● CompactFlash Card Type II ● MicroDrive ● Memory Stick (MS) ● MagicGate Memory Stick (MG) ● MagicGate Memory Stick Duo ● Memory Stick Select ● Memory Stick Duo (MS Duo) ● Memory Stick PRO (MS PRO) ●...

  • Page 8: Using The Web

    Table 1 Solving Common Problems (continued) Problem Possible Cause Solution Media card reader cannot The media card is a read-only Check the manufacturer’s documentation included with write to the media card. memory (ROM) card. your card to see if it writable. See the “Compatible Media Cards”...

Comments to this Manuals

Symbols: 0
Latest comments: