Advertisement
Available languages
Available languages
To
use a Sensor Cycle
•
Press POWER/CANCEl .....
Turn the knob to desired Sensor Cycle.
Select DRYNESS LEVEl. to adjust how dry you want the load. As the cycle runs, the
control
senses the dryness of the load and adjusts the time automatically
for the
selected
dryness
[eve[.
The initial
preset temperature
is the prefered
setting for drying
loads of different
garment types listed (see "Sensor Cycles").
If desired,
one alternate
temperature
may
be selected
to dry the load on a lower heat setting.
The next time the same cycle is
selected,
the alternate
temperature
is remembered
and displayed.
The original
(default) temperature
may be rese[ected.
The Delicate
cycle does not offer an alternate
temperatu
re.
Select the desired Options.
To make changes
during a Sensor Cycle:
•
Press START/PAUSE.
•
Adjust
I)ryness
I.evel.
ldamp
@less
@normal
@more
@ very dry [ ,dryn,ess
I
adjust
sensor
cycie
only
NOTE:
Dryness selections
can be made only while
using Sensor Cycles.
How the Sensi-Care
TM
Drying System Works
Moisture-sensing
strips and temperature
sensors inside
the dryer drum monitor
how fast
the load is drying,
how hot the air should
be, and when clothes
are dry. The system
automatically
stops the cycle to help save time and avoid overdrying.
To use a Timed Cycle
Turn knob to desired Timed
Cycle.
Press the TIME ADJUST + (plus) or-
(minus) until the desired drying
time is displayed.
Press the + (plus) or - (minus)
and the time will change by 1-minute
intervals.
Press
and hold the + (plus) or - (minus)
and the time will change by 5-minute
intervals.
NOTE: The Time Adjust
feature can be used only with the Timed
Cycles and the
Custom
Refresh cycle.
time
i
adjust
"_"
•
Press TEMP I.EVEI. until the desired temperature
illuminates.
[11 air fluff
[m extra low @ tow
@ medium
@ regular
NOTE: The Temp I.evel feature can be used only with Timed Cycles and the Custom
Refresh cycle.
NOTE:
During
a Timed
Cycle,
you can change the settings for Time, Temp, the Wrinkle
Prevent setting,
and the End Signal.
5.
(OPTIONAl_
STEP) If desired,
select OPTIONS.
For more details,
see "Options."
6.
(OPTIONAl_
STEP) If desired,
press END SIGNAL.
A signal will sound to alert you when a
cycle ends. For more details, see "End Signal."
7,
Press START/PAUSE.
Be sure the door is dosed.
•
If you do not press Start within
5 minutes
of selecting
the cycle,
the dryer
automatically
shuts off.
•
If you wish to end your drying
cycle after pressing Start, press POWER/CANCEl
.....
To stop
or pause
your
dryer
at any time
Open
the door or press START/PAUSE.
Press POWER/CANCEl.
to cancel
a cycle.
1o restart
the dryer
Close the door. Press START/PAUSE
until dryer starts.
NOTE:
Drying
will continue
from where the cycle was interrupted
if you dose the door and
press Start within
5 minutes.
If the cycle is interrupted
for more than 5 minutes,
the dryer will
shut off. Select new cycle settings before restarting
the dryer.
Select the correct
cycle and dryness [eve[ or temperature
for your load.
If a Sensor Cycle
is
running,
the display shows the estimated
cycle time when your dryer is automatically
sensing
the dryness
[eve[ of your
load. If a Timed Cycle
is running,
the display
shows the exact
number
of minutes
remaining
in the cycle.
Coo[ Down
tumbles
the load without
heat during
the last few minutes
of all cycles. Coo[
Down
makes the loads easier to handle
and reduces wrinkling.
The length of the Coo[ Down
depends on the load size and dryness
[eve[.
Drying
tips
•
Follow
care [abe[ directions
when they are available.
If desired,
add a fabric softener
sheet. Follow
package
instructions.
To reduce
wrinkling,
remove
the load from the dryer as soon as tumbling
stops. This is
especially
important
for permanent
press, knits, and synthetic
fabrics.
Avoid drying
heavy work
clothes together
with
lighter fabrics.
This could
cause
overdrying
of lighter fabrics
and lead to increased
shrinkage
or wrinkling.
Cycle tips
•
Dry most loads using the preset cycle settings.
•
Refer to the Sensor; or Timed
Preset Cycle
Settings chart (in the "Cycles"
section)
for a
guide to drying various
loads.
Drying
temperature
and dryness
level are preset when you choose a Sensor Dry
Cycle. You can select a different
dryness
level, depending
on your
load, by pressing
Dryness and choosing
More,
Normal,
Less, or Damp.
The initial
preset temperature
is
the preferred
setting;
howevei;
you may select an alternate
drying
temperature
by
pressing TEMP LEVEL. Once selected,
the new heat setting
will be retained
until reset
to the initial
preset temperature.
The Delicate
cycle does not allow
an alternate
temp
to be selected.
If you wish to adjust the cycle length of a Timed Cycle,
press the Timed Adjust
+ (plus)
or-
(minus).
Adjust the temperature
of a Timed Cycle by pressing Temp I_eve[ until the
desired temperature
is selected.
NOTE: You cannot choose a dryness level with Timed Cycles.
Advertisement
