Table of Contents
Advertisement
Legacy USB Support [Auto]
Legacy USB Support [Auto]
Legacy USB Support [Auto]
Legacy USB Support [Auto]
Legacy USB Support [Auto]
Allows you to enable or disable support for legacy USB devices. Setting to
[Auto] allows the system to detect the presence of legacy USB devices at
startup. If detected, the USB controller legacy mode is enabled. If no legacy
USB device is detected, the legacy USB support is disabled.
Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller [Enabled]
USB 2.0 Controller [Enabled]
USB 2.0 Controller [Enabled]
USB 2.0 Controller [Enabled]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
USB 2.0 Controller Mode [HiSpeed]
USB 2.0 Controller Mode [HiSpeed]
USB 2.0 Controller Mode [HiSpeed]
USB 2.0 Controller Mode [HiSpeed]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed ] [HiSpeed]
U S B M a s s S t o r a g e D e v i c e C o n f i g u r a t i o n
U S B M a s s S t o r a g e D e v i c e C o n f i g u r a t i o n
U S B M a s s S t o r a g e D e v i c e C o n f i g u r a t i o n
U S B M a s s S t o r a g e D e v i c e C o n f i g u r a t i o n
U S B M a s s S t o r a g e D e v i c e C o n f i g u r a t i o n
The items in this menu allows you to confgure the USB Mass Storage Class
devices. Select an item then press <Enter> to display the configuration
options.
Advanced
USB Mass Storage Device Configuration
USB Mass Storage Reset Delay
No USB Mass Storage device detected
v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
U S B M a s s S t o r a g e R e s e t D e l a y [ 2 0 S e c ]
U S B M a s s S t o r a g e R e s e t D e l a y [ 2 0 S e c ]
U S B M a s s S t o r a g e R e s e t D e l a y [ 2 0 S e c ]
U S B M a s s S t o r a g e R e s e t D e l a y [ 2 0 S e c ]
U S B M a s s S t o r a g e R e s e t D e l a y [ 2 0 S e c ]
Allows you to set the number of seconds POST waits for the USB
mass device after start unit command. Configuration options:
[10 Sec] [20 Sec] [30 Sec] [40 Sec]
A S U S N C L - D E S e r i e s
A S U S N C L - D E S e r i e s
A S U S N C L - D E S e r i e s
A S U S N C L - D E S e r i e s
A S U S N C L - D E S e r i e s
BIOS SETUP UTILITY
[20 Sec]
Number of seconds POST
waits for the USB mass
device after start
unit command.
Select Screen
Select Item
+-
Change Option
F1
General Help
F10 Save and Exit
ESC Exit
4 - 2 3
4 - 2 3
4 - 2 3
4 - 2 3
4 - 2 3
Advertisement
Table of Contents
