Asus NCL-D User Manual page 51

7 . 7 . 7 . 7 . S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 )
7 . S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 )
This connector is for a serial (COM) port. Connect the serial port
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
NCL-DE Series Serial port connectors
The serial port module is purchased separately.
8 . 8 . 8 . C P U a n d s y s t e m f a n c o n n e c t o r s ( 3 - p i n C P U _ F A N 1 / 2 , C P U a n d s y s t e m f a n c o n n e c t o r s ( 3 - p i n C P U _ F A N 1 / 2 ,
8 . 8 . C P U a n d s y s t e m f a n c o n n e c t o r s ( 3 - p i n C P U _ F A N 1 / 2 , C P U a n d s y s t e m f a n c o n n e c t o r s ( 3 - p i n C P U _ F A N 1 / 2 , C P U a n d s y s t e m f a n c o n n e c t o r s ( 3 - p i n C P U _ F A N 1 / 2 ,
R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 )
R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 )
The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W
max.) or a total of 2.1 A ~ 4.44 A (53.28 W max.) at +12V. Connect
the fan cables to the fan connectors on the motherboard, making sure
that the black wire of each cable matches the ground pin of the
connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
NCL-DE Series Fan connectors
A S U S N C L - D E S e r i e s A S U S N C L - D E S e r i e s
A S U S N C L - D E S e r i e s A S U S N C L - D E S e r i e s A S U S N C L - D E S e r i e s
COM2
PIN 1
CPU_FAN1
CPU_FAN1
REAR_FAN2
REAR_FAN1
CPU_FAN2
REAR_FAN1
GND
+12V
Rotation
FRNT_FAN1
FRNT_FAN2
FRNT_FAN1
GND
+12V
Rotation
CPU_FAN2
REAR_FAN2
Rotation
+12V
GND
FRNT_FAN2
GND
+12V
Rotation
2 - 3 1 2 - 3 1
2 - 3 1 2 - 3 1 2 - 3 1