Advertisement
3.
Secure the line card in the chassis by tightening the captive-screw with a Phillips
head screwdriver.
4.
Remove the dust cover from the SFP slot.
5.
Slide the SFP module into the slot until it clicks into place.
6.
Remove the dust cover from the fiber optic port on the SFP module.
7.
Connect the fiber optic cable to the port on the SFP module.
8.
Connect a twisted pair cable to the RJ-45 twisted pair port on the line card.
LEDs
information.
The RDY (Ready) LED displays general status
LED
State
Status/Operating Mode
RDY
Off
The line card is initializing the AT-S102 Management Software,
(Ready)
which takes approximately one minute, or the card is not receiving
power.
Green
The line card has initialized its management software and is ready to
transfer network traffic.
The operating mode of the line card is displayed by the SML, ML and OAM LEDs.
Operating Mode
SML
(Smart
MissingLink)
Link Test mode
Off
Off
Link Test mode with OAM
Off
Off
MissingLink mode
Off
On
MissingLink mode with OAM
Off
On
Smart MissingLink mode
On
Off
Smart MissingLink mode with OAM
On
Off
The SFP slot has three LEDs.
LED
Color
Description
LK
Off
The fiber optic port on the SFP transceiver has not formed a link
(Link)
with the remote device.
Green
The port has formed a link with the fiber port on the remote device.
Blinking
The media converter is operating in the Smart MissingLink mode
Green
and the twisted pair port has not formed a link with a network device.
AT
Off
The port is not connected to a fiber optic cable, has not formed a link
(Activity)
with the remote device, or is not receiving or transmitting packets.
Blinking
The fiber optic port on the SFP module is receiving or transmitting
Green
network packets.
1000M
Off
The SFP module is 100Base-FX.
Green
The SFP module is 1000Base-X.
The 10/100/1000Base-T twisted pair port has five LEDs.
LED
LK
(Link)
AT
(Activity)
FD
(Full
duplex)
1000M
and
100M
LEDs
Note
OAM
(Operations,
For more information on the Link LEDs, refer to the explanation of the media
ML
Administration
converter operating modes in the Converteon AT-S73, AT-S99, and AT-S102
(Missing Link)
and
Management Software User's Guide.
Maintenance)
ECO Friendly Button
Off
The recessed ECO Friendly button on the front panel of the line card is used to toggle the
On
low power mode, which controls the LEDs. You can use the button to turn off the LEDs to
conserve power when you are not monitoring them. To toggle the LEDs on or off, press
Off
the recessed button with a pointed object, such as the end of a straightened paperclip.
On
You can also toggle the low power mode with the AT-CV5M02 Management Card. The
low power mode does not affect the network operations of the line card or control the
Off
RDY LED.
On
Default Settings
The default settings for the media converter are listed here.
Feature
Basic Settings
Operating Mode
Maximum Frame Size
Twisted Pair Port
Ingress and Egress Filtering
Low Power Mode
Operating Mode DIP Switches
OAM Settings
Admin State
Mode
Maximum OAMPDU Size
4
Color
Description
Off
The port has not formed a link with a network device.
Green
The port has formed a link with a network device.
Flashing Green
The media converter is operating in the Smart MissingLink
mode and the fiber optic port on the SFP module has not
formed a link with a network device.
Off
The port is not receiving or transmitting network packets.
Blinking Green
The port is receiving or transmitting network packets.
Off
The port is operating in half-duplex mode.
Green
The port is operating in full-duplex mode.
100M - Off
The port is operating at 10 Mbps.
1000M - Off
100M - On
The port is operating at 100 Mbps.
1000M - Off
100M - Off
The port is operating at 1000 Mbps.
1000M - On
Default Setting
Link Test
10240 bytes
Auto-Negotiation with auto-MDI/MDI-X
None
Disabled
Enabled
Enabled
Passive
1518 bytes
Feature
Loopback Support
Enabled
Variable Retrieval Support
Enabled
Technical Specifications
Physical and Environmental
Dimensions (H x W x L)
22 mm x 73 mm x 130 mm
(.86 in. x 2.9 in. x 5.1 in.)
Weight
113 grams (0.25 lb.)
Operating Temperature
0° C to 40° C (32° F to 104° F)
Storage Temperature
-25° C to 70° C (-13° F to 158° F)
Operating Relative Humidity
5% to 90% RH (non-condensing)
Storage Relative Humidity
5% to 95% RH (non-condensing)
Operating Altitude Range
Up to 3,048 m (10,000 ft.)
MTBF
1,530,000 hours
Optical
Connector Type
SFP
Operating Speed
100 Mbps or 1000 Mbps (fixed speed)
Fiber Type
SFP Transceiver
Electrical Ratings
Power Consumption
8.5 Watts maximum
Electrical, Safety, and Emissions Statements
Standards: This product meets the following standards when installed in compliant host equipment.
U.S. Federal Communications Commission
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant
to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void your right
to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
Emission
FCC Class A, EN55022 Class A, VCCI Class A, C-TICK, CE
Warning
In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Immunity
EN55024
Electrical Safety
UL60950-1 (
UL
), EN60950-1 (TUV), CAN/CSA C22.2 No. 60950-1
c
us
Copyright © 2008 Allied Telesis, Inc. All rights reserved. No part of this publication may be
reproduced without prior written permission from Allied Telesis, Inc. www.alliedtelesis.com.
5
Default Setting
6
Advertisement
