Table of Contents
Advertisement
Quick Links
Edelbrock General Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before You Install Your Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What is Nitrous Oxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Steps for Working with Nitrous Oxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.0
1.1
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2
Jet Map Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.3
Engine Operation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4
Performer Kit Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.0
2.1
Nitrous Bottle Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2
Bottle Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3
Nitrous Bottle Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4
Nitrous Feed Line Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5
Solenoid Assembly and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6
Nitrous Plate Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.7
Fuel Pressure Take-Off Adapter Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.0
3.1
Nitrous Electrical Components Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2
Wide Open Throttle Module Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3
Nitrous Electrical System Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.4
Wide Open Throttle (WOT) Module Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.5
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.6
Arming Switch and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.7
Final Solenoid and WOT Module Installation Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.0
4.1
Fuel System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2
Nitrous System Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.0
Solenoid Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6.0
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-16
©2007 Edelbrock Corporation
Brochure #63-0478
EDELBROCK NITROUS SYSTEM
FOR 2005-2007 MUSTANG GT
CATALOG #70410
Table of Contents
Page 1 of 16
Page #
Catalog #70410
Rev. 9/08 - AJ/mc
Advertisement
Table of Contents
Related Manuals for Edelbrock Nitrous System 70410
Summary of Contents for Edelbrock Nitrous System 70410
-
Page 1: Table Of Contents
Before You Install Your Edelbrock Nitrous System ........ -
Page 2: Edelbrock General Warranty
Our warranty service and repair facility is located at 2700 California Street, Torrance, California 90503. Customers who believe they have a defective product should either return it to the dealer from which it was purchased or ship it directly to Edelbrock along with proof of purchase and a complete description of the problem. -
Page 3: Before You Install Your Edelbrock Nitrous System
5. When washing components, ensure the clean components are completely dry, free of oils, and solvents. Failure to remove all liquids could cause component or system failure. 6. Always turn the bottle off before making any repairs to the nitrous delivery system. ©2007 Edelbrock Corporation Brochure #63-0478 Caution!! ❑... -
Page 4: Introduction To Your Edelbrock 2005-2007 Mustang Gt Nitrous System
Always take care when handling a full bottle of nitrous oxide. Please follow all safety methods during the installation of your Edelbrock Nitrous System, and follow all vehicle regulations and road laws when using your nitrous system. -
Page 5: Performer Kit Bill Of Materials
❑ 1 .038” Taper Face Jet ❑ 1 .058” Taper Face Jet ❑ 1 1/8”NPT Plug ❑ 1 Mustang Fuel Pressure Take-Off Adapter ©2007 Edelbrock Corporation Brochure #63-0478 7-10 Qty. Description Item # ❑ 1 Pressure Adapter O-Ring ❑ 1 Performer Fuel Solenoid ❑... -
Page 6: Nitrous System Installation
Device (PRD) Bottle Safety Information 1. Do not attempt to remove the bottle valve. Please return your bottle to Edelbrock if service is required to the siphon tube inside the bottle or the bottle valve itself. 2. Never heat the outside of your nitrous bottle with an open flame like that of a torch. -
Page 7: Bottle Orientation
An Edelbrock nitrous bottle cannot be mounted upside-down. Edelbrock does not offer a non-siphon tube bottle for automotive use. If the bottle must be mounted parallel to the axles of the vehicle (sideways), the label must be angled at approximately 45 degrees toward the front of the vehicle. -
Page 8: Nitrous Feed Line Mounting
Select the corresponding fuel jet and place in the red fitting of the nitrous plate. Connect the 3AN x 15” 90° red fuel hose from the outlet fitting of the fuel solenoid to the fitting on the nitrous plate with the jet installed. ©2007 Edelbrock Corporation Brochure #63-0478... -
Page 9: Nitrous Plate Installation
Connect the 4AN fitting to the inlet fitting of your Performer Fuel Solenoid using the supplied 3 foot 4AN fuel feed line. ©2007 Edelbrock Corporation Brochure #63-0478 Page 9 of 16 Catalog #70410... -
Page 10: Electrical System Installation
Important: The wiring hardware and instructions included with this kit are intended for 12-volt electrical systems only. Before attempting to wire your Edelbrock Performer Nitrous Oxide System, examine and follow the wiring diagram on the following page. Please call the Edelbrock Technical Department with any questions concerning electrical wiring. -
Page 11: Wide Open Throttle Module Wiring Diagram
Wide Open Throttle (WOT) Module Installation The WOT module includes 3 feet of color-coded wires and terminals to make the electrical system installation for your Edelbrock Nitrous System as easy as possible. We recommend that you do not cut any lengths of wires from the wire harness or complete the wiring of the system until all of the mechanical components are securely mounted in their permanent locations. -
Page 12: Wiring
2. Check all connections for exposed wire, try to keep all wire within the insulation or use shrink wrap to prevent any loose wires from shorting out. ©2007 Edelbrock Corporation Brochure #63-0478 Page 12 of 16 Catalog #70410... -
Page 13: Before You Run Your Vehicle Using Your Edelbrock Nitrous System
Before You Run Your Vehicle Using Your Edelbrock Nitrous System You have just completed the installation of your Edelbrock Nitrous System. It is time to perform some basic system checks to ensure all of the work you have done is correct and ready to operate properly. The following procedure is designed to validate... -
Page 14: Troubleshooting Your Edelbrock Nitrous System
Troubleshooting Your Edelbrock Nitrous System How to use our Troubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required. Determine your problem (symptom), identify the potential problem (cause) and correct the problem (action required). - Page 15 Acquire the right size jets and install correct jets. 8. Excessive fuel pressure. a. Perform Fuel Pressure Test Procedure. b. Install fuel pressure gauge. Regulate pressure to proper settings. ©2007 Edelbrock Corporation Brochure #63-0478 Page 15 of 16 Adjustment screw for the WOT voltage setting.
- Page 16 Check bottle temperature. Maintain 80 to 85 degrees of bottle surface temperature. c. Check bottle valve. Open valve fully d. Check bottle orientation. Mount bottle properly. ©2007 Edelbrock Corporation Brochure #63-0478 Edelbrock Corporation 2700 California Street Torrance, CA 90503 Tech Line: 1-800-416-8628 E-mail: Edelbrock@Edelbrock.com...
Need help?
Do you have a question about the Nitrous System 70410 and is the answer not in the manual?
Questions and answers