Table of Contents
Advertisement
Quick Links
PERFORMER RPM SINGLE TO DUAL-STAGE UPGRADE KIT
Edelbrock General Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before You Install Your Edelbrock Nitrous System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
What is Nitrous Oxide? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Tips for Working with Nitrous Oxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.0
1.1
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2
Jet Map Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3
Engine Operation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.4
Performer RPM Single to Dual Stage Upgrade Kit Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.0
2.1
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2
2-Stage Electrical System Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.3
2-Stage Wire Harness Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4
2-Stage Nitrous Electrical System Installation Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.0
3.1
Fuel System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.2
Nitrous System Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.0
Baseline Tuning Suggestions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.0
Ignition Timing and Nitrous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6.0
Solenoid Inspection and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.0
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Catalog #70005
Rev. 07/08 - AJ/mc
Catalog #70005
Table of Contents
Page 1 of 20
Page #
©2008 Edelbrock Corporation
Brochure No. 63-70005
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Edelbrock 70005
Summary of Contents for Edelbrock 70005
-
Page 1: Table Of Contents
Before You Install Your Edelbrock Nitrous System ........ -
Page 2: Edelbrock General Warranty
Our warranty service and repair facility is located at 2700 California Street, Torrance, California 90503. Customers who believe they have a defective product should either return it to the dealer from which it was purchased or ship it directly to Edelbrock along with proof of purchase and a complete description of the problem. -
Page 3: Before You Install Your Edelbrock Nitrous System
❑ Basic engine operation and tuning techniques which include: -Fuel pressure measurement techniques -Timing adjustment techniques ℡ ℡ Anytime you have questions or concerns with your Edelbrock Nitrous System, please call our Catalog #70005 Rev. 07/08 - AJ/mc Caution!! Technical Support Hotline at 1-800-416-8628 before you start your engine. -
Page 4: What Is Nitrous Oxide
Tighten the nitrous line to the bottle. g. Slowly open the nitrous bottle valve, listening for leaks. h. Perform leak checks on all affected fittings and the bottle fitting. Catalog #70005 Rev. 07/08 - AJ/mc Page 4 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005... -
Page 5: Introduction To Your Single To Dual Stage Upgrade Kit
Introduction to your Edelbrock Single to Dual Stage Upgrade Kit Within the pages of this manual is information, safety tips and operation instructions for your new Edelbrock Nitrous System. Watch for these symbols to know where to go for information. -
Page 6: Jet Map Information
6. Advanced tuning required. Suggested timing adjustment is just a guideline. Engine component modifications may affect final timing set point. Edelbrock recommends an NGK spark plug with a heat range of -9 to -11 depending on the nitrous power level being tuned. When in doubt, always go to the next cooler heat range plug. -
Page 7: Engine Operation Considerations
When designing your fuel system, plan on your pumps and lines flowing at least 0.1 gallons per hour per horsepower at rated pressure. The testing at Edelbrock was conducted with a fuel pressure of 6 to 6.5 psi. Any variation from this fuel pressure will cause your final air/fuel ratio to change. Consult our technical department for any questions on fuel pressure and its effects on final air/fuel ratios when using nitrous oxide. -
Page 8: Performer Rpm Single To Dual Stage Upgrade Kit Bill Of Materials
4AN 12” Steel Braided Hose, Red 1 ea 4AN to 3AN 12” Steel Braided Hose, Blue 1 ea 4AN to 3AN 8” Steel Braided Hose, Red Misc Various Included Jets Page 8 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005... -
Page 9: Nitrous System Installation
20. Repeat steps 18 and 19 using the blue lines and Blue Y Fitting for the nitrous solenoids. 21. Wire per the diagram on page 11. Catalog #70005 Rev. 07/08 - AJ/mc Page 9 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005... -
Page 10: Nomenclature Descriptions
Important: The wiring hardware and instructions included with this kit are intended for 12-volt electrical systems only. Before attempting to wire your Edelbrock Performer nitrous oxide system, examine and follow the wiring diagram on the following page. Please call the Edelbrock Technical department with any questions concerning electrical wiring. -
Page 11: 2-Stage Wire Harness Diagram
Wire Schematic Origin and Destination Map Catalog #70005 Rev. 07/08 - AJ/mc STAGE STAGE RELAY RELAY WHITE WHITE BLACK BLACK BLUE STAGE STAGE SOLENOID SOLENOID GROUND Page 11 of 20 SWITCHED +12V GROUND MICRO SWITCH BLACK GROUND PUSHBUTTON ©2008 Edelbrock Corporation Brochure No. 63-70005... -
Page 12: 2-Stage Nitrous Electrical System Installation Procedure
The wire harness attached to the relay and fuse holder includes 8 feet of color-coded wires to make the electrical system installation for your Edelbrock Nitrous System as easy as possible. We recommend not cutting any lengths of wires from the wire harness or complete the wiring of the nitrous system until all of the mechanical components are securely mounted in their permanent locations. -
Page 13: Before You Run Your Vehicle Using Your Edelbrock Nitrous System
Before You Run Your Vehicle Using Your Edelbrock Nitrous System You have just completed the installation of your Edelbrock Nitrous System. It is time to perform some basic system checks to ensure all of the work you have done is correct and ready to operate properly. The following procedure is designed to... -
Page 14: Baseline Tuning Suggestions
.035" with a shorter preferably thicker ground strap. Never try to gap a plug designed for a .060" gap down to.035". Edelbrock suggest an NGK spark plug with a heat range of -9 to -11 depending on the nitrous power level being tuned. When in doubt, always go to the next cooler heat range plug. -
Page 15: Ignition Timing And Nitrous
See Testing Checklist for more testing methodology helpful hints. Catalog #70005 Rev. 07/08 - AJ/mc 38 degrees “total” 2 degrees “retard” 2 degrees “retard” 34 degrees “total” Page 15 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005... -
Page 16: Solenoid Inspection And Maintenance
Remove any contaminants that may be present. Make sure solenoid body is clean, dry and free of oils before assembly. 10. Replace the O-Ring, plunger and piston spring. 11. Re-assemble solenoid by reversing disassembly procedure. Catalog #70005 Rev. 07/08 - AJ/mc Page 16 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005... - Page 17 Troubleshooting Your Edelbrock Nitrous System How to use our Troubleshooting Flowchart: The troubleshooting of a nitrous system is basic and straightforward. The symptom chart is divided by symptom, cause and action required. Determine your problem (symptom), identify the potential problem (cause) and correct the problem (action required).
- Page 18 Consult a book concerning proper wiring methods. 10. Malfunctioning nitrous solenoid. a. Inspect solenoid wiring. See “Electrical System Installation” section. Repair wiring. b. Inspect solenoid. See symptom #2. Rebuild/replace solenoid. Catalog #70005 Rev. 07/08 - AJ/mc Page 18 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005...
- Page 19 2. Weak ignition/ignition component failure. a. Inspect ignition components. Replace worn components. ii. Upgrade ignition system to high performance high load capable ignition components. Catalog #70005 Rev. 07/08 - AJ/mc Page 19 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005...
- Page 20 Check bottle temperature. Maintain 80 to 85 degrees of bottle surface temperature. c. Check bottle valve. Open valve fully d. Check bottle orientation. Mount bottle properly. Catalog #70005 Rev. 07/08 - AJ/mc Page 20 of 20 ©2008 Edelbrock Corporation Brochure No. 63-70005...
Need help?
Do you have a question about the 70005 and is the answer not in the manual?
Questions and answers