Table of Contents
Advertisement
VCR
Recording a Programme with Automatic Stop
GB
EJECT
AUX
3
4
4
OK
6
5
LENGTH 2:30
SET LENGTH :
G
PRESS
REC
30
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1
Switch on the television.
2
To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3
Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
4
Select:
N
The station to be recorded using the PROG ( or ) buttons
or
N
The LINE1, LINE2 source using the INPUT SEL. button for
a satellite tuner or external video source
Result:
The channel number is displayed and the
programme can be seen on the television.
5
Select the recording speed by pressing the SPEED button as
many times as required (see page 28).
6
Hold the REC button (G) down for a while to start recording.
Result:
The record indicator appears on the television
screen and DVD-VCR display. An index is recorded
on the tape (see page 38).
7
Press the REC button ( G) several times to increase the
recording time in:
N
30-minute intervals up to four hours
N
1-hour intervals up to nine hours
Result:
The length is displayed on the television displays.
The selected programme is recorded for the length
of time requested. At the end of that time, the DVD-
VCR stops recording automatically and power off.
8
If you wish to cancel the recording before the end, press
STANDBY/ON.
☛
If the end of the tape is reached while recording:
N
The recording stops and power off.
☛
This function is not available in DVD recording
Using the
Feature
Before presetting your DVD-VCR:
N Switch on both the television and your DVD-VCR
N Check that the date and time are correct
N Insert the cassette on which the programme is to be
recorded (safety tab intact)
Up to six programmes can be preset.
1
Press the TIMER button.
Result:
The
Timer Method
is displayed.
2
Press the corresponding
or
buttons, until the
❷
option is selected.
3
Press the ❿ button to select
G-Code
.
Result:
A message is displayed to allow you to enter the
G-Code code.
☛
If all six programmes have been set, the message
is Full
is displayed. Refer to page 34 if you wish to
cancel a preset recording.
4
Press the numeric buttons to enter the code opposite the pro
gramme that you wish to record in your television magazine.
➢
If you wish to correct the G-Code code that you are
entering:
N
Press the ➛ button until the digit to be corrected is
cleared
N
Enter the correct digit
5
Press the OK button.
Result:
The information concerning the programme is
displayed.
☛
When using the G-Code function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the
or
buttons. Refer to the following page
❷
if:
N
The programme number or times flash
N
You wish to modify the programme
6
If the programme and times are correct, press the RETURN
button.
7
Press the STANDBY/ON button to activate the timer.
8
Refer to page 34 if you wish to:
N
Check that your VCR has been programmed correctly
N
Cancel a preset recording
☛
The numbers next to each TV programme listing are
G-CODE code numbers, which allow you to
programme your videorecorder instantly with the
remote control. Tap in the G-CODE code for the
programme you wish to record.
™ G-CODE is a trademark of Gemstar Development Corporation. The G-CODE system is
manufactured under licence from Gemstar Development Corporation.
VCR
OK
1
Timer Method
G-Code
Standard
G-Code
Timer
G-Code
Code
Code
: 0 - 9
Correct
:
STANDBY/ON
OPEN/CLOSE
7
GB
31
Advertisement
Table of Contents
