Alarm Demonstration - Philips HF3485/60 User Manual

EnglisH
14
snoozing
1 Tap on the surface of the Wake-Up light with your finger (preferably with your knuckle)
when you hear the alarm sound (Fig. 24).
The best place to tap on the appliance is somewhere near the bottom or on the lid, to prevent
knocking the appliance off your bedside table.
The lamp continues to be on at the selected intensity level, but the alarm sound stops. After
,
9 minutes, the alarm sound is automatically played again.
Note: The 9-minute snooze time is fixed. This time cannot be adjusted.
switching the alarm function off and on
1 To switch off the alarm function when the alarm goes off, push down the control lever to the
bottom position (Fig. 25).
Note: The lamp stays on to light your room. You can switch off the lamp by pressing the lamp on/off
button.
Note: If you forget to switch off the alarm, the alarm (sound and/or light) automatically switches off after
90 minutes.
2 If you want the alarm to go off at one of the set alarm times the next day, set the control
lever to alarm 1 or alarm 2 again.

Alarm demonstration

If you want to get a quick demonstration (60 seconds) of the gradually increasing light intensity and
sound level, activate the test function of the appliance.
1 Simultanuously press and hold the menu - or + buttons until the word TEST appears on the
display (Fig. 26).
2 Simultanuously press the menu - or + buttons again to stop the demonstration.
Note: The appliance continues to run the alarm demonstration until you press the menu + and - button
again. The test automatically stops after 9 hours.
Using the radio/playing music from a UsB stick
switching on the radio
1 To switch on the radio, press the radio on/off button (Fig. 27).
The radio starts to play.
,
Note: The radio function has 3 preset stations. To select one of the preset stations, press the SELECT
button below the display.
2 To select the desired radio frequency, press the menu - or + button (Fig. 28).
Tip: To scan radio frequencies automatically, press and hold the menu - or + button for approx. 2 seconds.
Tip: To make sure you get a good radio signal, fully unwind the antenna and move it around until you
have found a position at which reception is best.
3 To switch off the radio, press the radio on/off button again.
Changing the preset radio stations
The radio of the Wake-Up light has 3 preset radio stations.If you want to set different radio stations
as the preset stations, follow the steps below.
1 Press the radio on/off button to switch on the radio (Fig. 29).
The display shows P1, which is preset station 1 (Fig. 22).
,
Note: Press the SELECT button one or more times if you want to select another preset station.
2 To scan radio frequencies in order to change the preset station, press the menu - or +
button (Fig. 28).
The appliance automatically stores the selected radio frequency.
,
Playing music from a UsB stick
Note: You can only use music on a USB stick if it is in MP3 or WMA format. The appliance does not play
any other format.You can check this on your computer. The extension of the files should be .mp3 or
.wma. For more information, see chapter 'USB specifications'.
1 To play music from a USB stick, press the radio on/off button twice (Fig. 29).
If there is a USB stick in the USB socket, the appliance automatically starts scanning the
,
number of MP3 or WMA files on the USB stick. This may take a few minutes. Then the
number of songs is shown on the display and the appliance starts playing the first song on the
USB stick.
If the appliance detects that the files on the USB stick are not in MP3 or WMA format, the
,
display shows 'ERR'.
2 To select the desired song file, press the menu - or + button (Fig. 28).
3 To stop playing music from the USB stick, press the radio on/off button again.
Note: The songs are ordered based on the date that the music was put on the USB stick. If you want the
songs to be played in a specific order, put them in this order on your computer first and then copy them
to your USB stick.
setting the volume
1 To set the volume for the radio or music from a USB stick, press the volume increase or
decrease button (Fig. 30).
You can choose a volume level between 1 and 20.
Note: The volume level you have selected is automatically set as the volume level for the alarm as well.
Dusk simulation
You can use the dusk simulation when you want the light and/or the sound of the Wake-up Light to
stay on and dim gradually during a set period of time (15 minutes to 1.5 hours) before you go to
sleep. The lamp and/or sound switch off automatically after the set time.
1 Switch on the lamp and/or the radio or music from a USB stick. See sections 'Using the
appliance as a bedside lamp' and/or 'Using the radio/playing music from a USB stick' in this
chapter.
2 Follow the steps in section 'Menu functions' in this chapter to select the dusk simulation
function and to set the dusk simulation time.
You can choose a time from 15 to 90 minutes (15, 30, 45, 1:00 or 1:30).
,
Note: After the set time, no matter whether only the light and/or the radio are on, the dusk simulation
switches off both light and sound.
Tip: You can also press the light on/off button for 3 seconds to activate the dusk simulation function
(Fig. 31).
Using the appliance as a bedside lamp
You can use the appliance as a bedside lamp.
1 To switch on the lamp, press the lamp on/off button (Fig. 14).
Note: It takes approx. 1 second for the lamp to go on. This is normal, the lamp needs to heat up.
EnglisH
15