Alliance Laundry Systems FRONTLOAD WASHERS FLW1526C Installation And Operation Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Washer
  5. FLW1526C
  6. Installation and operation manual
Alliance Laundry Systems FRONTLOAD WASHERS FLW1526C Installation And Operation Manual

Alliance Laundry Systems FRONTLOAD WASHERS FLW1526C Installation And Operation Manual

Frontload washers metered commercial
Hide thumbs Also See for FRONTLOAD WASHERS FLW1526C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operation & Installation Manual
Frontload Washers
Para bajar una copia de estas instrucciones
en español, visite www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Metered Commercial
www.comlaundry.com
FLW1526C
Part No. 802734R5
September 2010

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FRONTLOAD WASHERS FLW1526C and is the answer not in the manual?

Questions and answers

Related Manuals for Alliance Laundry Systems FRONTLOAD WASHERS FLW1526C

Summary of Contents for Alliance Laundry Systems FRONTLOAD WASHERS FLW1526C

  • Page 1 Frontload Washers Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com. Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Metered Commercial www.comlaundry.com FLW1526C Part No. 802734R5 September 2010...
  • Page 3 Always contact the distributor, service agent, or the manufacturer about any problems or conditions you do not understand. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING W030...

  • Page 4: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information...
  • Page 5 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 7: Start Washer... 27 Indicator Lights ... 27 Maintenance ... 28 User-Maintenance Instructions... 28 Cold Weather Care... 28 Care of Your Washer ... 28 Cleaning Glass Sealing Area ... 28 Replacing Hoses...

  • Page 6: Safety Information

    NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions (Save These Instructions)
  • Page 7 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 20. Be sure water connections have a shut-off valve and that fill hose connections are tight. CLOSE the shut-off valves at the end of each wash day.

  • Page 8: Installation

    28 in. (71.1 cm) 1.5 in. (3.8 cm) 1.5 in. (3.81 cm) Inside Diameter 1.86 in. (4.72 cm) Outside Diameter © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation Coin Slide Models 21.56 in. (54.76 cm) Electronic Control Models 22.06 in.

  • Page 9: Before You Start

    Level Figure 1 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT NOTE: If the washer is delivered on a cold day (below freezing), or is stored in an unheated room or area during the cold months, do not attempt to operate it until the washer has had a chance to warm up.

  • Page 10: Installing The Washer

    Do not install the washer on carpeting, soft tile, a platform or other weakly supported structures. Figure 2 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Position and Level the Washer WARNING Washers elevated above floor level must be anchored to that elevated surface, base or platform.

  • Page 11: Step 3: Connect Fill Hoses

    Locknut Rubber Foot Figure 3 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 3: Connect Fill Hoses Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for two weeks or more.

  • Page 12: Connecting Hoses

    Plain Rubber Washer Filter Screens Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT IMPORTANT: Hoses and other natural rubber parts deteriorate after extended use. Hoses may develop cracks, blisters or material wear from the temperature and constant high pressure they are subjected to.

  • Page 13: Step 4: (Non-Gravity Drain Models Only) Connect Drain Hose To Drain Receptacle

    Risers (Air Cushions) Water Supply Faucets Figure 6 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 4: (Non-Gravity Drain Models Only) Connect Drain Hose to Drain Receptacle Remove the drain hose from its shipping position on the rear of the washer by removing the shipping tape.

  • Page 14: Standpipe Installation

    HEIGHT Standpipe 2 in. (5.08 cm) or 1-1/2 in. (4 cm) Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 5: (Gravity Drain Models Only) Connect Drain Outlet to Drain System Remove drain fitting (four inches long) and hose clamp from accessories bag.

  • Page 15: Step 6: Remove The Shock Sleeves And Shipping Brace

    For leveling purposes, the washer may be tilted a maximum of 6 inches (152.4 mm) in any direction. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Shock Sleeves Motor Mount Hooked End of Shipping Brace...

  • Page 16: Step 8: Plug In The Washer

    110/120 Volts AC (alternating current) 15 Amps. Refer to Figure 12 to determine correct polarity of the wall receptacle. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 120±12 V.A.C. 120±12 V.A.C.

  • Page 17: Grounding Instructions

    Figure 12, the qualified electrician should correct the problem. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 9: Check Installation Refer to Installer Checklist on the back cover of this manual and make sure that washer is installed correctly.

  • Page 18: Vending

    1. Remove slide extension parts from parts accessories bag included in unit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 2. If installing a Greenwald coin slide, position extension lever (to be installed on extension bracket) with arm that has one star facing down.

  • Page 19: Models Prepped For Card Reader

    Lever Off Switch Figure 16 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 6. Check to make sure coin slide is operating properly by inserting coins and starting a cycle. The IN USE light will turn on, or flash if it is already on, to indicate proper operation.

  • Page 20: Operation

    DELICATE cycle. The cycle includes agitation and final spin speeds that maintain the load’s balance and minimize wear to the articles. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Step 2: Close Loading Door Close the loading door tightly.

  • Page 21: Step 3: Add Laundry Supplies

    Bleach Fabric Softener Figure 20 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 4: Set Fabric Selector Set regular loads at NORMAL or PERM PRESS. Set delicate loads at DELICATE. Step 5: Set WASH/RINSE Temperatures...

  • Page 22: Indicator Lights

    The washer will stop (pause) shortly before the first spin and final spin. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Rapid Advance The Rapid Advance feature allows the owner to quickly advance through an active cycle to a specific cycle step.

  • Page 23: Operation Instructions For Mdc Washers

    802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Close Loading Door Close loading door tightly. The washer will not operate with the loading door open.

  • Page 24: Step 3: Add Laundry Supplies

    Dispenser drawer requires a special tool for removal. Contact a service person if removal is necessary. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 4: Set Fabric Selector and Wash Temperature Push touchpad for NORMAL/HOT, NORMAL/ WARM, PERM PRESS/WARM or DELICATES/ COLD cycle.

  • Page 25: Step 5: Insert Coin(S) Or Card

    To Insert Card Insert card into opening. Figure 29 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Start Washer After vend price has been satisfied, push the START pad. DOOR MUST BE CLOSED TO START WASHER.

  • Page 26: Indicator Lights

    START flashes one second on and one second off when the full vend price has been satisfied. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT IMPORTANT: If washer fails to operate properly after installation, make sure electrical service and water supply faucets are turned on.

  • Page 27: Operation Instructions For Netmaster Washers

    Figure 32 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 3: Add Laundry Supplies Open dispenser drawer. Measure and add low sudsing, high efficiency (HE) detergent (1), bleach (2) and fabric softener (3) to the dispenser drawer (refer to Figure 33).

  • Page 28: Copyright, Alliance Laundry Systems Llc – Do Not Copy Or Transmit

    DELICATES PRESS WARM COLD Figure 35 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Insert Coin(s) or Card To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital display. START...

  • Page 29: Indicator Lights

    DOOR LOCKED is lit whenever the door is locked. The door cannot be opened when this light is on. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT INSERT COIN/CARD INSERT COIN/CARD is lit to prompt the user to insert coins or card to satisfy the vend price.

  • Page 30: User-Maintenance Instructions

    © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Maintenance Replacing Hoses Hoses and other natural rubber parts deteriorate after extended use.

  • Page 31: Reinstallation Of Shipping Materials

    Refer to Installation section, step 6 for proper procedures whenever the washer is moved. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Cleaning Foreign Object Trap The washer’s pump has a trap that may collect foreign objects.

  • Page 32: Troubleshooting

    Laundry load may be oversudsing or overloaded. Make sure you are using low-sudsing, high efficiency (HE) detergent and proper load sizes.  Make sure outside perimeter of the door glass where seal contacts glass is clean. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Troubleshooting Possible Cause/Solution 802734...
  • Page 33 “H” on the valve bracket) and cold faucet is connected to cold mixing valve (indicated with “C” on the valve bracket).  Make sure laundry room water heater is adjusted properly. 802734 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Possible Cause/Solution Troubleshooting...

  • Page 34: Contact Information

    Phone: (920) 748-3121 Nameplate Figure 40 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT When calling or writing about your unit, PLEASE GIVE THE MODEL AND SERIAL NUMBERS. The model and serial numbers are located on the nameplate.

  • Page 36: Installer Checklist

    Drain Receptacle. CHECK (Gravity Drain Models Only) • Connect Drain Outlet to Drain System. CHECK © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT • Position and Level the Washer. CHECK H135IE0A H135IE0A • Remove the Shock COLD Sleeves and Shipping Brace.

Table of Contents

Save PDF