Index Safety information Installation Getting to know your dishwasher How to fill the salt How to fill rinse aid How to fill the detergent Not suitable for the dishwasher Arranging crockery, glasses, etc. in the dishwasher Programme overview Washing dishes How to keep your dishwasher in shape Care and maintenance Fault finding...
Safety information At time of delivery Check packaging and dishwasher immediately for signs of transport damage. If the appliance is damaged, do not put it into use but contact your supplier or customer service without delay. Please dispose of packaging materials properly. During installation Place the dishwasher and connect it up in accordance with the installation instructions.
If your family includes children This appliance is not intended for use by persons (including children) with reduced physical,sensory or mental capcabilities, or lack of experience and knowledge,unless they have been given supervi- sion or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they to not play with the appliance.
Installation Positioning the appliance Change the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to facilitate proper installation. Levelling the appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level.
Drain hose connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. If necessary, fit a syphon trap (U-bend) with a connecting piece for the drain hose (fig.C).
Installation cont.. Stage 1 Supplied with the appliance is a plastic (self adhesive) anticondensation strip, this should be fixed to the underside of your worktop along the front edge. The adjustable feet of the ap- pliance allow it to be raised up to 870mm, if the space between the floor and the underside of the work surface is greater than fig 1a 870mm, then the appliance should be positioned on suitable...
Stage 5 Align the top of the decor door with adjacent cabinets. Gently open door whilst supporting the decor door. Once in the lowered position, secure the decor door using the fixing screws provided as shown in the diagram. Cover the screw heads using the plas- tic caps provided.
Assembly Instructions for Integrated Dishwasher Technical Information for Installation The control panel (except in the completely built-in version) can be easily aligned with the kitchen drawers, using the spacers supplied with the appliance (see Fig.1 and Fig.2). The height of the control panel is 115 mm, while the three spacers each add 7.5 mm in height.
Fastening the Bracket to the Wooden Panel (Fig.5 - totally built-in )- (Fig.6 integrated with control panel) At the point marked, drill holes 2 mm in diameter . If the panel is made of chip board , only drill through the veneer. If the panel is made of solid wood, the holes can be made deeper.
Installation of Continuous Base Moulding Position the washing machine in the cut-out in the kitchen cabinet: 1. Install the continuous base moulding , following the manufacturer’s instructions . 2. Slowly open the door of the dishwasher to check to see if the door strikes or rubs against the base moulding.
How to fill the salt Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water.
Adjusting salt consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize and customize the level of salt consumption so that it remains at a minimum. To adjust salt consumption, proceed as follows: Unscrew the cap from the salt container;...
How to fill rinse aid Rinse aid This product makes dishes sparkle and helps them to dry without spotting. The dispenser is located on the inside panel of the door . When the low rinse aid indicator “ D ” lights , you must load rinse aid .
How to fill the detergent Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Programme overview". The detergent dispenser is located on the inside panel of the door.
Not suitable for the dishwasher What you should not put into the dishwasher Cutlery and tableware manufactured in whole or part from wood.They become faded and unsightly in appearance.Furthermore,the adhesives that are used are not suitable for the temperature that occur inside the dishwasher.Delicate decorative glassware and vases,special antique or irreplaceable china.
Arranging crockery, glasses, etc. in the dishwasher Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from be- coming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they are soaked before washed.
How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). Position the dishes and cookware so that they do not get moved by the spray of water.
Programme overview Type of Condi- Type of Amount of crokery e.g. Wash tion of china, pots/ food food Description of cycle 3 in 1 pan s, food programme Load remains remains cutiery, remains glasses, etc Pre-wash with hot water. Extended wash at 70°C. Soups, Rinses with cold water.
Detergent Delayed Energy Water Duration in Rinse Aid Start consump- consump- Extended minutes Prewash tion in kWh tion in litres Wash 1.44 1.25 1.11 1.00 1.05 0.95 1.01 0.95 0.40 0.30 0.90 0.78 0.02 0.02...
Washing dishes Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc., as well as the amount and condition of food remains, with the details contained in the wash cycle table.The corresponding programme sequence, duration and consumption details are shown in the right half of the overview.
Switching the dishwasher ON Turn on the tap. Open the door. Set ON-OFF button “I” to ON. Press programme button “B” , programme indicator “ A” lights and the time-remaining indicator “ ” dis- plays the time of the programme.. If the door is closed, the programme indicator “A”...
Delayed start programming You can delay the start of a programme in increments of 1 hour up to 24 hours. Switch dishwasher Immediately press the Delayed Start button “ G ”, the delayed start indicator lights, the delayed start time indicator “ ”...
3in1 function When using "3 in 1"combination products, the rinse-aid and salt lights are no longer useful. It may be helpful therefore to switch the rinse aid off (please note that only some dishwashers have this facility) and selecting the lowest possible setting for water hardness. If you decide to switch to the use of a standard detergent system we advise that you: 1: Refill both the salt and rinse aid compartments.
Tabs With Classic Tabs you can put your dirtiest dishes straight into the dishwasher. The tab contains StainSoakers which dissolve instantly to soften really dried on food residues such as baked on egg and cheese sauces. The blue layer then works to break down and lift off food remains while the white layer cleans all traces of dirt away for a spotless and brilliant finish.
How to keep your dishwasher in shape After Every Wash After every wash, set the main switch “I” to off and leave the door slightly ajar so that moisture and odors are not trapped inside. Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher, do not use solvents or abrasive cleaning products.
Care and maintenance Regular inspection and maintenance of your appliance helps to prevent problems from occurring.This saves time and aggravation.You should therefore carefully inspect the inside of your dishwasher from time to time. Overall condition of appliance Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: Clean the interior of the dishwasher thorughly with a detergent solution.
Fault finding Resolving minor problems yourself Experience has shown that you can resolve most problems that rise during normal daily usage yourself, without having to call out a service engineer.Not only does this save costs,but it also means that the appliance is available for use again that much sooner.
When “ ” (F) blinks. Have you checked whether: the drain hose is crimped or bent. the drain hose is too high. When “ ” (F) blinks. Have you checked whether: the water is turned on and the hose is connected properly; the water supply to the house is on and has sufficient pressure;...
Water remains inside appliance after programme has ended Blockage or kind in drainage hose. Pump is jammed. Filters are blocked. The programme is still running. Wait for the programme to end ..during washing Unusual amount of foam is creased Normal washing up liquid has been poured into the rinse-aid container.
Plastic items are discoloured Not enough detergent was added to dispenser. Detergent has insuffcient bleaching properties. Use a detergent containing a chemical bleaching agent. White stains are left on crockery, glasses have a milky appearance Not enough detergent was added to dispenser compartment. Amount of rinse-aid was set too low.
Technical data 60 cm Width Depth 58 cm Height 82 cm Capacity 12 standard place settings Mains water pressure 0.03-1.0MPa Power voltage 220-240V~ 50Hz Maximum current intensity 2150W Total absorbed power Important information Notes on waste disposal Old appliances still have some residual value. An environment-friendly method of disposal will ensure that valuable raw materials can be recovered and used again.
Information on comparability tests implemented in compliance with EN 50242 Appliance loaded in accordance with standard specifications. Example of loaded dishwasher: See Fig 1, 2 and 3. Capacity: 12 place settings Comparability programme: Light wash Rinse-aid setting: 5 Detergent: 25g+5g Fig.1 Fig.2 Fig.3...
WB: Wiring box SV: Softener valve HR: Heating element relay DS: Door switch OS: Overflow switch SSS: Spy salt switch WS: Water level switch IV: Inlet valve SRS: Spy rinse aid switch DP: Drain pump WP: Washing pump TS: Temperature sensor DV: Dispenser valve TL: Temperature limiter SLV: Single layer valve...