Cisco PVDM2 24DM - Digital Modem Module User Manual page 32

show modem configuration (pvdm2)
S24 = 0
S25 = 5
S26 = 1
S27 = 73
S28 = 0
S29 = 70
S30 = 0
S31 = 6
S32 = 17
S33 = 19
S36 = 7
S37 = 0
S38 = 20
S39 = 3
S40 = 88
S41 = 139
S46 = 138
S48 = 7
S82 = 128
S82 = 21
S91 = 13
S92 = 13
S95 = 0
S200 = 223
S202 = 2
S210 = 13
S220 = 11
S221 = 50
S222 = 0
S223 = 23
S224 = 0
Table 2
Table 2
S Register
S00
S01
S02
S03
S04
S05
Cisco IOS Release 12.4(9)T, 12.4(11)XW, and 12.4(20)T
32
Cisco PVDM2-12DM, PVDM2-24DM, and PVDM2-36DM Digital Modem Packet Voice Data Modules
0 second Sleep Inactivity Timer
Delay 5 (sec for async; 0.01 sec otherwise) to ignore DTR
Delay 0.01 seconds RTS to CTS Delay
Sync./Async. selection &Q5 Dial up line (&L0),
Internal clock (&X0), Bell mode (B1),
39%-61% make/break ratio at 10 pulses per second (&P0)
Flash Dial Modifier Time is 700 ms
No Disconnect Inactivity Timer
Single line connect message controlled by S95, Wn and Vn
Auto line speed detection enabled(N1)
Error correction progress messages full reporting (W1)
XON character is 0x11
XOFF character is 0x13
Attempt MNP connection, if fails, Normal mode
Attempt automode connection
20 seconds Delay Before Forced Hang Up
RTS/CTS (&K3)
Disable extended services(-K0)
Break Handling (\Kn) not supported
NMP block size 128 chars (\A1)
Compression selection is MNP 5 and V.42 bis
Retrain and fallback/fall forward disabled
Execute error correction protocol with compression
V.42 negotiation enabled
Break Handling Options/LAPM Break Control = 0x80
-13 dBm Transmit Level in analog modulations
-13 dBm Transmit Level for the fax mode
CONNECT result code indicates DTE speed
Not append/ARQ to CONNECT 'rate' in error-correction
Disable CARRIER 'rate' result code
Disable PROTOCOL 'identifier' result code
Disable COMPRESSION 'type' result code
Enable K56Plus
K56Plus protocol follows the setting of ATNn
Enables V.90 digital pad compensation
Disable Display Tx and Rx HNDSHK states
No automatic CX802xx/CX803xx status response
K56flex Tx level is -12 dBm V90 Tx level is -12 dBm
Disable V.42 selective reject
2400,2800,3000,3200,3429 V.34 asymmetric rates enabled
Duration of Answer Tone is 0xB (in units of 450ms)
500 ms Duration of Billing Delay
-12 dBm V.90 PCM Transmit Level
Digital detect timer (100ms per unit)
describes the S register fields shown in the display.
show modem configuration Field Descriptions for V12 Modems
Field
Rings to Auto-Answer
Ring Counter
Escape Character
Carriage Return Character
Line Feed Character
Backspace Character
Description
0 to 255. Default is 0.
0 to 255. Default is 0.
Default is 43.
Default is 13.
Default is 10.
Default is 8.