Table of Contents
Advertisement
External control
About the external control
This monitor has three external control terminals.
●
MAKE/TRIGGER terminal (RJ-45): The following external control
systems are available.
1 MAKE (make contact) system:
Controls the monitor by short-circuiting the corresponding pin
terminal to the GND pin terminal, or disconnecting (opening) it.
2 TRIGGER (trigger) system:
Controls the monitor by sending the pulse signal
instantaneously to the corresponding pin terminal.
→ "Using the MAKE/TRIGGER system" on the right.
●
RS-485 terminal (RJ-45): Controls the monitor with the RS-485
system (→ "Using the serial communication" on page 28).
●
RS-232C terminal (D-sub 9-pin): Controls the monitor with the RS-
232C system (→ "Using the serial communication" on page 28).
Set the following items of "REMOTE SETTING" in SET-UP MENU
according to the external control terminal and control system (→
"SERIAL TYPE," "PARALLEL TYPE" on page 24).
Control
Control system
terminal
MAKE/
MAKE
TRIGGER
TRIGGER
terminal
RS-485
terminal
Serial
communication
RS-232C
terminal
*1
For a monitor connected to a personal computer etc, select
the terminal the equipment is actually connected to. For other
monitors, select "RS485."
Control priority is as follows.
MAKE > TRIGGER = serial communication = buttons and menu on
the monitor
●
You can use external control even when "CONTROL LOCK" is set to
"VOL.LOCK" or "ALL LOCK." (→ page 25)
●
When the monitor is off (on standby), external control is not
available. But certain external controls (starting/terminating
communication, turning on the monitor) are available through the
serial communication. (→ page 29)
<MAKE/TRIGGER system>
You can control the monitor by a personal computer or dedicated
*2
controller
.
●
"Using the MAKE/TRIGGER system" on the right.
*2
The controller is not commercially available. Consult your dealer if
you need it.
<Serial communication>
PC, etc.
RS-485 IN
RS-485
or
OUT
RS-232C
●
For the details, see page 28.
26
The settings of this unit
"SERIAL
"PARALLEL
TYPE"
TYPE"
setting
setting
—
—
TRIGGER
*1
RS-485
RS485
*1
RS-232C
RS232C
RS-485
RS-485
RS-485
OUT
IN
IN
Using the MAKE/TRIGGER
system
The MAKE/TRIGGER terminal is configured as follows.
You can assign a function to each pin terminal in "REMOTE SETTING."
(→ "PIN1, PIN2, PIN3, PIN4, PIN5" in "PARALLEL TYPE" on page 24)
●
You cannot change the functions assigned to the pin terminals
from 6th to 8th.
This is a female
terminal.
*1
The 6th pin terminal controls turning on or off the tally lamp
(available to control even when the 7th pin terminal is invalid).
*2
The 7th pin terminal makes the external control valid/invalid.
MAKE
Make sure to control the terminal by the MAKE system.
To assign the functions to the pin terminals
—
For the operation procedure, see page 18.
1 Select "REMOTE SETTING" on the SET-UP MENU.
—
2 Set "PARALLEL TYPE" to "SET."
3 Select a pin name ("PIN1" – "PIN5") for which you want
to assign a function, then select the function you want
to assign.
For the selectable functions, see the table on page 29.
Operation of the external control
1 Set "PARALLEL TYPE" of "REMOTE SETTING" to "MAKE"
or "TRIGGER" in the SET-UP MENU.
2 Short-circuit the 7th pin terminal (ENABLE) to the
8th pin terminal (GND) so that the monitor can be
controlled by the external control.
3 When the "MAKE" system is selected:
Operate each function by short-circuiting the
corresponding pin terminal to the 8th pin terminal
(GND) or opening it.
When the "TRIGGER" system is selected:
Operate each function by pulse control, that is short-
circuiting the corresponding pin terminal to the 8th pin
terminal (GND) for about 1 second and opening it.
●
When changing the input with MAKE system, only one pin terminal
must be short-circuited. (Other pin terminals must be opened.)
●
When selecting the "TRIGGER" system, you can operate only one
function at a time. Operate the functions one by one.
RS-485
OUT
Pin No.
Pin name
1
PIN1
2
PIN2
PIN3
3
4
PIN4
5
PIN5
*1
6
TALLY
*2
7
ENABLE
8
GND
Advertisement
Table of Contents
