Juniper E120 - RELEASE 11.1.X MODULE GUIDE 3-26-2010 Manual
Juniper E120 - RELEASE 11.1.X MODULE GUIDE 3-26-2010 Manual

Juniper E120 - RELEASE 11.1.X MODULE GUIDE 3-26-2010 Manual

E series broadband services routers module guide

Advertisement

Quick Links

E Series
Broadband Services Routers
E120 and E320 Module Guide
Release 11.1.x
Juniper Networks, Inc.
1194 North Mathilda Avenue
Sunnyvale, California 94089
USA
408-745-2000
www.juniper.net
Published: 2010-03-26

Advertisement

Table of Contents
loading

Summary of Contents for Juniper E120 - RELEASE 11.1.X MODULE GUIDE 3-26-2010

  • Page 1 E Series Broadband Services Routers E120 and E320 Module Guide Release 11.1.x Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 408-745-2000 www.juniper.net Published: 2010-03-26...
  • Page 2 This guide provides an overview and description of the line modules (LMs), switch route processor (SRP) modules, switch fabric modules (SFMs), and input/output adapters (IOAs) available for the Juniper Networks E120 and E320 Broadband Services Routers. NOTE: A release may support multiple versions of a module or IOA. For information, see Software Compatibility in JUNOSe System Basics Configuration Guide, Chapter 6, Managing Modules.
  • Page 3 Table 1: Modules and IOAs Module/IOA Type Module Label First JUNOSe Support Page Line Module LM-4 7.0.1 LM-10 Uplink 7.2.0 UPLINK LM-10 8.0.0 10G LM LM-10 ADV 10.1.0 10G ADV LM SRP Module SRP-100 SRP-100 7.0.1 SRP-120 SRP-120 8.2.0 SRP-320 SRP-320 7.3.0 SFM Module...
  • Page 4: Table Of Contents

    E120 and E320 11.1.x Module Guide Table 1: Modules and IOAs (continued) Module/IOA Type Module Label First JUNOSe Support Page OC3/STM1-8 ATM IOA ES2-S1 7.0.1 OC3-8 STM1 ATM IOA OC12/STM4 ATM IOA OC12/STM4-2 ATM IOA ES2-S1 7.0.1 OC12-2 STM4 ATM IOA OC12/STM4 POS IOA OC12/STM4-2 POS IOA ES2-S1...
  • Page 5 LM-4 Line Module LM-4 Line Module ES2 4G LM Module label Not applicable Number of ports First supported: 7.0.1 Software release 176 W maximum Description Acts as frame forwarding engines for the physical interfaces Responsible for processing data traffic Pairs with IOAs to process data from different types of network connections FFA ASIC Type Supports a line rate of 128–byte packets on IOAs...
  • Page 6 E120 and E320 11.1.x Module Guide See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Alarms, errors, and events Managing Modules. LM-4 Line Module...
  • Page 7 LM-10 Uplink Line Module LM-10 Uplink Line Module ES2 10G UPLINK LM Module label Not applicable Number of ports First supported: 7.2.0 Software release 150 W maximum Description Acts as frame forwarding engines for the physical interfaces Processes up to 10 Gb of data traffic Pairs with ES2–S2 10GE PR IOA only In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4) If you install the line module in a slot other than slot 2 or slot 4, it will be disabled...
  • Page 8 E120 and E320 11.1.x Module Guide When lit, LED indicates: LEDs OK (green) Self-test passed FAIL (red) Failure detected ONLINE (green) Online with no alarms or errors REDUN (green) Redundant card available See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Alarms, errors, and events Managing Modules.
  • Page 9 LM-10 Line Module LM-10 Line Module ES2 10G LM Module label Not applicable Number of ports First supported: 8.0.0 Software release 198 W maximum Description Acts as frame forwarding engines for the physical interfaces Processes up to 10 Gb of data traffic Pairs with ES2–S2 10GE PR IOA and ES2–S1 GE-8 IOA In a SRP-100 configuration, it must be installed in a turbo slot only (slot 2 or slot 4) If you install the line module in a slot other than slot 2 or slot 4, it will be disabled...
  • Page 10 E120 and E320 11.1.x Module Guide When lit, LED indicates: LEDs OK (green) Self-test passed FAIL (red) Failure detected ONLINE (green) Online with no alarms or errors REDUN (green) Redundant card available See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Alarms, errors, and events Managing Modules.
  • Page 11 LM-10 ADV Line Module LM-10 ADV Line Module ES2 10G ADV LM Module label Not applicable Number of ports First supported: 10.1.0 Software release 190 W maximum Description Acts as frame forwarding engines for the physical interfaces Processes up to 10 Gb of data traffic Pairs with ES2–S2 10GE PR IOA, ES2-S1 REDUND IOA, ES2–S3 GE-20 IOA, and ES2–S1 GE-8 IOA In an SRP-320 configuration, it can be installed in any slot...
  • Page 12 E120 and E320 11.1.x Module Guide SRP-100 Module SRP-100 Module label SRP IOA IOA label Not applicable Number of IOA ports First supported: 7.0.1 Software release 75 W maximum Description Switch route processor (100 Gbps) Performs system management, route table calculations and maintenance, forwarding table computations, statistics processing, configuration storage, and other control plane functions Has 2 GB of memory...
  • Page 13 SRP-100 Module Board-level LEDs: LEDs OK (green) Self-test passed FAIL (red) Failure detected ONLINE (green) Online with no alarms or errors REDUN (green) Module is the spare system controller, is up, and is ready to take the role of the online system controller. When LED is not lit, module is not acting as the spare system controller.
  • Page 14 E120 and E320 11.1.x Module Guide SRP-120 Module SRP-120 Module label SRP IOA IOA label Not applicable Number of IOA ports First supported: 8.2.0 Software release 140 W maximum Description Switch route processor (120 Gbps) Performs system management, route table calculations and maintenance, forwarding table computations, statistics processing, configuration storage, and other control plane functions Has 4 GB of memory...
  • Page 15 SRP-120 Module Board-level LEDs: LEDs OK (green) Self-test passed FAIL (red) Failure detected ONLINE (green) Online with no alarms or errors REDUN (green) Module is the spare system controller, is up, and is ready to take the role of the online system controller. When LED is not lit, module is not acting as the spare system controller.
  • Page 16 E120 and E320 11.1.x Module Guide SRP-320 Module SRP-320 Module label SRP IOA IOA label Not applicable Number of IOA ports First supported: 7.3.0 Software release 140 W maximum Description Switch route processor (320 Gbps) Performs system management, route table calculations and maintenance, forwarding table computations, statistics processing, configuration storage, and other control plane functions Has 4 GB of memory...
  • Page 17 SRP-320 Module Board-level LEDs: LEDs OK (green) Self-test passed FAIL (red) Failure detected ONLINE (green) Online with no alarms or errors REDUN (green) Module is the spare system controller, is up, and is ready to take the role of the online system controller. When LED is not lit, module is not acting as the spare system controller.
  • Page 18 E120 and E320 11.1.x Module Guide SFM-100 Module SFM-100 Module label Not applicable IOA label Not applicable Number of IOA ports First supported: 7.0.1 Software release 40 W maximum Description Switch fabric module (100 Gbps) Works with the SRP-100 module to create a switch fabric Must be installed only with SRP-100 module and SFM–100 modules Not applicable Capability...
  • Page 19 SFM-120 Module SFM-120 Module SFM-120 Module label Not applicable IOA label Not applicable Number of IOA ports First supported: 8.2.0 Software release 95 W maximum Description Switch fabric module (120 Gbps) Works with the SRP-120 module to create a switch fabric The 120–Gbps fabric allocates 10 Gbps of overall bandwidth to each line module slot.
  • Page 20 E120 and E320 11.1.x Module Guide SFM-320 Module SFM-320 Module label Not applicable IOA label Not applicable Number of IOA ports First supported: 7.3.0 Software release 95 W maximum Description Switch fabric module (320 Gbps) Works with the SRP-320 module to create a switch fabric The 320–Gbps fabric allocates 10 Gbps of overall bandwidth to each line module slot.
  • Page 21 GE-4 IOA GE-4 IOA ES2-S1 GE-4 IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 21 W maximum Description Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot. Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths.
  • Page 22 E120 and E320 11.1.x Module Guide Up to four LC-style fiber-optic connectors Cables and connectors (multimode [SX] ) Transmit power: min: –9.5 dBm max: –3 dBm Receive input power: min: –20 dBm max: 0 dBm See the following corresponding table (SX Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 23 GE-4 IOA When lit, LED indicates: LEDs OK (green) Physical link is connected properly and is functioning properly FAIL (red) Failure detected Port LEDs: LK (green) Ethernet link is up ACT (green) Blinks when there is Ethernet traffic being received Alarms, errors, and events See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 5, Configuring Ethernet Interfaces.
  • Page 24 E120 and E320 11.1.x Module Guide Table 6: Single-strand SFPs Pairing Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 9 microns TX 1310, RX 1550 10 (6.2 miles), matching SFP must have the same operating range Pairs with TX 1550 / RX 1310 9 microns TX 1550 / RX 1310 10 (6.2 miles), matching SFP must have...
  • Page 25 GE-8 IOA GE-8 IOA ES2-S1 GE-8 IOA IOA label Number of IOA ports First supported: 7.2.0 Software release 32 W maximum Description Gigabit Ethernet Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot. Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths Uses either optical or copper SFPs.
  • Page 26 E120 and E320 11.1.x Module Guide One LC full duplex connector Cables and connectors (multimode [SX]) Transmit power: min: –9.5 dBm max: –3 dBm Receive input power: min: –20 dBm max: 0 dBm See the following corresponding table (SX Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 27 GE-8 IOA Board-level LEDs: LEDs OK (green) IOA is online and is functioning properly FAIL (red) Failure detected Port LEDs: LK (green) Ethernet link is up ACT (green) Blinks when Ethernet traffic is being received See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Alarms, errors, and events Chapter 5, Configuring Ethernet Interfaces.
  • Page 28 E120 and E320 11.1.x Module Guide Table 11: Single-strand SFPs Pairing Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 9 microns TX 1310, RX 1550 10 (6.2 miles), matching SFP must have the same operating range Pairs with TX 1550 / RX 1310 9 microns TX 1550 / RX 1310 10 (6.2 miles), matching SFP must have...
  • Page 29 GE-20 IOA GE-20 IOA ES2-S3 GE-20 IOA IOA label Number of IOA ports First supported: 9.0.0 Software release 92 W maximum Description Full-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot. Uses a range of small form-factor pluggable (SFP) transceivers to support different modes and cable lengths Uses either optical or copper SFPs.
  • Page 30 E120 and E320 11.1.x Module Guide Can be paired with an ES2 10G LM. Line module redundancy compatibility Must be installed in the same redundancy group as an ES2 10G LM and ES2–S1 REDUND IOA combination. Not applicable Port redundancy support Maximum range is 100 meters on CAT5 cable.
  • Page 31 GE-20 IOA Board-level LEDs: LEDs OK (green) Physical link is connected properly and is functioning properly FAIL (red) Failure detected Port LEDs: LK (green) Ethernet link is up ACT (green) Blinks when there is Ethernet traffic being received See Monitoring Ethernet Interfaces in JUNOSe Physical Layer Configuration Guide, Chapter 5, Alarms, errors, and events Configuring Ethernet Interfaces.
  • Page 32 E120 and E320 11.1.x Module Guide Table 16: Single-strand SFPs Pairing Fiber Type Nominal Wavelength (nm) Maximum Operating Range (kilometers) 9 microns TX 1310, RX 1550 10 (6.2 miles), matching SFP must have the same operating range Pairs with TX 1550 / RX 1310 9 microns TX 1550 / RX 1310 10 (6.2 miles), matching SFP must have...
  • Page 33 10GE IOA 10GE IOA ES2-S1 10GE IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 40 W maximum Description Full-height module Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths. Ethernet (IEEE 802.3ae) Capability 10Gb Base-SR/LR/ER/ZR...
  • Page 34 E120 and E320 11.1.x Module Guide One LC full duplex connector Cables and connectors (single-mode [LR]) Transmit power: min: –8.2 dBm max: 0.5 dBm Receive input power: min: –14.4 dBm max: 0.5 dBm See the following corresponding table (LR Fiber Optic Cabling) for cabling requirements.
  • Page 35 10GE IOA Table 17: SR Fiber Optic Cabling Minimal Modal Bandwidth at Fiber Type 850 nm (MHz*km) Maximum Operating Range (meters) 62.5 microns 26 (85.3 ft) 33 (108.27 ft) 50 microns 66 (216.54 ft) 82 (269.03 ft) 2000 300 (984.25 ft) Table 18: LR Fiber Optic Cabling Maximum Operating Range Fiber Type...
  • Page 36 E120 and E320 11.1.x Module Guide 10GE PR IOA ES2-S2 10GE PR IOA IOA label Number of IOA ports 1 active, 1 redundant First supported: 7.2.0 Software release 48 W maximum Description Full-height module Uses a range of 10-gigabit small form-factor pluggable (XFP) transceivers to support different modes and cable lengths.
  • Page 37 10GE PR IOA One LC full duplex connector Cables and connectors (multimode [SR]) Transmit power: min: –7.3 dBm max: –1.0 dBm Receive input power: min: –9.9 dBm max: –1.0 dBm See the following corresponding table (SR Fiber Optic Cabling) for cabling requirements. See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 38 E120 and E320 11.1.x Module Guide Board-level LEDs: LEDs OK (green) IOA online and is functioning properly FAIL (red) Failure detected Port LEDs: LK (green) Ethernet link is up ACT (green) Blinks when Ethernet traffic is being received Port labels: W Working port P Protect port (LK blinks when active cable is attached even though it is not the active working port)
  • Page 39 10GE PR IOA Table 21: SR Fiber Optic Cabling Minimal Modal Bandwidth at Fiber Type 850 nm (MHz*km) Maximum Operating Range (meters) 62.5 microns 26 (85.3 ft) 33 (108.27 ft) 50 microns 66 (216.54 ft) 82 (269.03 ft) 2000 300 (984.25 ft) Table 22: LR Fiber Optic Cabling Maximum Operating Range Fiber Type...
  • Page 40: Oc3/Stm1-8 Atm Ioa

    E120 and E320 11.1.x Module Guide OC3/STM1-8 ATM IOA ES2-S1 OC3-8 STM1 ATM IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 50 W maximum Description Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot.
  • Page 41 OC3/STM1-8 ATM IOA Up to eight LC full duplex connectors Cables and connectors (single-mode intermediate [IR-1]) Transmit power: min: –15 dBm max: –8 dBm Center wavelength: 1310 nm Receive input power: min: –34 dBm max: –7 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 42: Oc12/Stm4 Atm Ioa

    E120 and E320 11.1.x Module Guide OC12/STM4-2 ATM IOA ES2-S1 OC12-2 STM4 ATM IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 40 W maximum Description Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot.
  • Page 43 OC12/STM4-2 ATM IOA Up to two LC full duplex connectors Cables and connectors (single-mode intermediate [IR-1]) Transmit power: min: –15 dBm max: –8 dBm Center wavelength: 1310 nm Receive input power: min: –28 dBm max: –7 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 44: Oc12/Stm4 Pos Ioa

    E120 and E320 11.1.x Module Guide OC12/STM4-2 POS IOA ES2-S1 OC12-2 STM4 POS IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 30 W maximum Description Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot.
  • Page 45 OC12/STM4-2 POS IOA Up to two LC full duplex connectors Cables and connectors (single-mode intermediate [IR-1]) Transmit power: min: –15 dBm max: –8 dBm Center wavelength: 1310 nm Receive input power: min: –28 dBm max: –7 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 46: Oc48/Stm16 Ioa

    E120 and E320 11.1.x Module Guide OC48/STM16 POS IOA ES2-S1 OC48 STM16 POS IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 30 W maximum Description Half-height module See “Module and Slot Combinations” on page 75 for more information on combining IOAs in a slot.
  • Page 47 OC48/STM16 POS IOA Up to one LC full duplex connector Cables and connectors (single-mode intermediate [IR-1]) Transmit power: min: –5 dBm max: 0 dBm Center wavelength: 1266 through 1310 nm Receive input power: min: –18 dBm max: –0 dBm Rated for 15 km (9.3 miles) of 9-micron core cable See E120 and E320 Hardware Guide, Chapter 5, Cabling the Router for more information.
  • Page 48: Redundancy Ioa

    E120 and E320 11.1.x Module Guide Redundancy IOA ES2-S1 REDUND IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 10 W maximum Description Full-height module Provides redundancy for line modules Inserted in slot 0 and 11 only Provides switchover when a line module fails Capability Provides N+1 redundancy for line modules...
  • Page 49: Service Ioa

    Service IOA Service IOA ES2-S1 SERVICE IOA IOA label Number of IOA ports First supported: 7.0.1 Software release 10 W maximum Description Full-height module Provides tunnel server functionality Pairs with associated line module to receive data from and transmit data to other line modules with ingress and egress ports Tunnelling Capability...
  • Page 50: Srp Ioa

    E120 and E320 11.1.x Module Guide SRP IOA SRP IOA Module label Not applicable IOA label Number of IOA ports First supported: 7.0.1 Software release 15 W maximum Description Pairs with SRP module Interfaces with the SRP modules through the system's midplane. Ethernet (IEEE 802.3) Capability 10/100Base-T...
  • Page 51 SRP IOA See Monitoring Modules in JUNOSe System Basics Configuration Guide, Chapter 6, Alarms, errors, and events Managing Modules. SRP IOA...
  • Page 52 IOA has not yet been fully qualified by Juniper Networks. If you use a feature before it has been fully qualified, it is your responsibility to ensure that it operates correctly in your targeted configuration.
  • Page 53 E120 and E320 11.1.x Module Guide Table 25: Ethernet IOAs with ES2 4G LM (continued) ES2–S1 GE-4 IOA (with ES2 ES2–S1 GE-8 IOA (with ES2 ES2–S1 10GE IOA (with ES2 Protocol or Application 4G LM) 4G LM) 4G LM) Bridged IP Cisco HDLC DHCP external server DHCP local server...
  • Page 54 Appendix A: IOA Protocol Support Table 25: Ethernet IOAs with ES2 4G LM (continued) ES2–S1 GE-4 IOA (with ES2 ES2–S1 GE-8 IOA (with ES2 ES2–S1 10GE IOA (with ES2 Protocol or Application 4G LM) 4G LM) 4G LM) IPv6 neighbor discovery IS-IS J-Flow Statistics L2TP/IPSec...
  • Page 55 E120 and E320 11.1.x Module Guide Table 25: Ethernet IOAs with ES2 4G LM (continued) ES2–S1 GE-4 IOA (with ES2 ES2–S1 GE-8 IOA (with ES2 ES2–S1 10GE IOA (with ES2 Protocol or Application 4G LM) 4G LM) 4G LM) PPPoE Remote loopback Subscriber interfaces (static) Subscriber interfaces...
  • Page 56 Appendix A: IOA Protocol Support Table 26: Ethernet IOAs with ES2 10G Uplink LM (continued) Protocol or Application ES2–S2 10GE PR IOA (with ES2 10G Uplink LM) Cisco HDLC DHCP external server DHCP local server DHCPv6 local server DVMRP and GRE support access side DVMRP and GRE support server side Dynamic interfaces Ethernet raw mode encapsulation in Martini layer 2 circuits...
  • Page 57 E120 and E320 11.1.x Module Guide Table 26: Ethernet IOAs with ES2 10G Uplink LM (continued) Protocol or Application ES2–S2 10GE PR IOA (with ES2 10G Uplink LM) LAC support peer side LNS support peer side Local loopback MDL (maintenance data link) Mobile IP home agent MPLS Yes (LER only)
  • Page 58 Appendix A: IOA Protocol Support Table 27: Ethernet IOAs with ES2 10G LM ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G LM) 10G LM) ES2 10G LM) Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels APS/MSP...
  • Page 59 E120 and E320 11.1.x Module Guide Table 27: Ethernet IOAs with ES2 10G LM (continued) ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G LM) 10G LM) ES2 10G LM) Yes (except for fast Yes (except for fast Yes (except for fast...
  • Page 60 Appendix A: IOA Protocol Support Table 27: Ethernet IOAs with ES2 10G LM (continued) ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G LM) 10G LM) ES2 10G LM) Multilink Frame Relay Multilink PPP Network Address Translation (NAT)
  • Page 61 E120 and E320 11.1.x Module Guide Table 28: Ethernet IOAs with ES2 10G ADV LM ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G ADV LM) 10G ADV LM) ES2 ADV 10G LM) Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels...
  • Page 62 Appendix A: IOA Protocol Support Table 28: Ethernet IOAs with ES2 10G ADV LM (continued) ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G ADV LM) 10G ADV LM) ES2 ADV 10G LM) Yes (except for fast Yes (except for fast Yes (except for fast...
  • Page 63 E120 and E320 11.1.x Module Guide Table 28: Ethernet IOAs with ES2 10G ADV LM (continued) ES2–S1 GE-8 IOA (with ES2 ES2–S3 GE-20 IOA (with ES2 ES2–S2 10GE PR IOA (with Protocol or Application 10G ADV LM) 10G ADV LM) ES2 ADV 10G LM) Multilink Frame Relay Multilink PPP...
  • Page 64 Appendix A: IOA Protocol Support OCx/STMx ATM IOAs Table 29: OCx/STMx ATM IOA Protocol or Application ES2–S1 OC3–8 STM1 ATM IOA ES2–S1 OC12–2 STM4 ATM IOA Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels APS/MSP BERT BGP/MPLS VPNs Bridged Ethernet Bridged IP Cisco HDLC...
  • Page 65 E120 and E320 11.1.x Module Guide Table 29: OCx/STMx ATM IOA (continued) Protocol or Application ES2–S1 OC3–8 STM1 ATM IOA ES2–S1 OC12–2 STM4 ATM IOA IP multicast IP reassembly for tunneled packets IPSec IPv6 IPv6 multicast IPv6 neighbor discovery IS-IS J-Flow Statistics L2TP/IPSec L2TP over MPLS...
  • Page 66 Appendix A: IOA Protocol Support Table 29: OCx/STMx ATM IOA (continued) Protocol or Application ES2–S1 OC3–8 STM1 ATM IOA ES2–S1 OC12–2 STM4 ATM IOA Remote loopback Subscriber interfaces (static) Subscriber interfaces (dynamic) Transparent bridging Tunnel-server ports Yes (shared only) Yes (shared only) Unified ISSU VPLS (network interfaces) VPLS (virtual core interfaces)
  • Page 67 E120 and E320 11.1.x Module Guide OCx/STMx POS IOAs Table 30: OCx/STMx POS IOA Protocol or Application ES2–S1 OC48 STM16 POS IOA ES2–S1 OC12–2 STM4 POS IOA Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels APS/MSP BERT BGP/MPLS VPNs Bridged Ethernet Bridged IP Cisco HDLC...
  • Page 68 Appendix A: IOA Protocol Support Table 30: OCx/STMx POS IOA (continued) Protocol or Application ES2–S1 OC48 STM16 POS IOA ES2–S1 OC12–2 STM4 POS IOA IP multicast IP reassembly for tunneled packets IPSec IPv6 IPv6 multicast IPv6 neighbor discovery IS-IS J-Flow Statistics L2TP/IPSec L2TP over MPLS LAC support access side...
  • Page 69 E120 and E320 11.1.x Module Guide Table 30: OCx/STMx POS IOA (continued) Protocol or Application ES2–S1 OC48 STM16 POS IOA ES2–S1 OC12–2 STM4 POS IOA PPPoE Remote loopback Subscriber interfaces (static) Subscriber interfaces (dynamic) Transparent bridging Tunnel-server ports Yes (shared only) Yes (shared only) Unified ISSU VPLS (network interfaces)
  • Page 70 Appendix A: IOA Protocol Support Service IOA Table 31: Service IOA Protocol or Application ES2–S1 SERVICE IOA Accepts traffic destined for GRE tunnels or DVMRP (IP-in-IP) tunnels APS/MSP BERT BGP/MPLS VPNs Bridged Ethernet Bridged IP Cisco HDLC DHCP external server DHCP local server DVMRP and GRE support access side DVMRP and GRE support server side...
  • Page 71 E120 and E320 11.1.x Module Guide Table 31: Service IOA (continued) Protocol or Application ES2–S1 SERVICE IOA IPSec IPv6 IPv6 multicast IPv6 neighbor discovery IS-IS J-Flow Statistics L2TP/IPSec LAC support access side LAC support peer side LNS support peer side Local loopback MDL (maintenance data link) Mobile IP home agent...
  • Page 72 Appendix A: IOA Protocol Support Table 31: Service IOA (continued) Protocol or Application ES2–S1 SERVICE IOA Subscriber interfaces (static) Yes (over GRE tunnels only) Subscriber interfaces (dynamic) Yes (over GRE tunnels only) Transparent bridging Tunnel-server ports Yes (dedicated only) Unified ISSU VPLS (network interfaces) VPLS (virtual core interfaces) VRRP...
  • Page 73 E120 and E320 11.1.x Module Guide Service IOA...
  • Page 74 Appendix B Module and Slot Combinations This appendix lists module and IOA slot combinations and contains the following sections: Module Combinations on page 75 IOA Slot Combinations on page 76 Module Combinations Line modules can only be paired with specific IOA, SFM, and SRP modules. See Table 32 on page 75 for valid combinations.
  • Page 75 E120 and E320 11.1.x Module Guide Table 32: Module Combinations (continued) Modules ES2 4G LM ES2 10G UPLINK LM ES2 10G LM ES2 10G ADV LM SFM-320 – IOA Modules ES2-S1 GE-4 – – – ES2-S1 GE-8 – ES2-S3 GE-20 –...
  • Page 76 Appendix B: Module and Slot Combinations Table 33: IOA Locations and Combinations Combined with Upper/Right Bay Lower/Left Bay Both Bays Other IOAs in Hot-Swapping (Adapter 0) (Adapter 1) Concurrently Same Slot Support ES2-S1 GE-4 ES2-S1 GE-8 Yes (GE-8 when paired with ES2 4G LM or ES2 10G LM;...
  • Page 77 E120 and E320 11.1.x Module Guide IOA Slot Combinations...
  • Page 78 Appendix C Module Name Cross-Reference Information Module Name Cross-Reference Information on page 79 Module Name Cross-Reference Information Use Table 34 on page 79 to find the label name, software display name, and model number of a module. Table 34: Module Naming Reference Label Name Software Display Name Model Number...
  • Page 79 E120 and E320 11.1.x Module Guide Table 34: Module Naming Reference (continued) Label Name Software Display Name Model Number ES2-S1 GE-8 IOA GE-8 IOA ES2-GE8S1-IOA ES2-S3 GE-20 IOA GE-20 IOA ES2-GE20S3-IOA ES2-S1 10GE IOA 10GE IOA ES2-10GES1-IOA ES2-S2 10GE PR IOA 10GE PR IOA ES2-10GES2-IOA ES2-S1 OC3-8 STM1 ATM IOA...
  • Page 80: Product Reclamation And Recycling Program

    Product Reclamation and Recycling Program on page 81 Product Reclamation and Recycling Program Juniper Networks is committed to environmentally responsible behavior. As part of this commitment, we continually work to comply with environmental standards such as the European Union’s Waste Electrical and Electronic Equipment (WEEE) Directive and Restriction of Hazardous Substances (RoHS) Directive.
  • Page 81 E120 and E320 11.1.x Module Guide Products returned through our reclamation process are recycled, recovered, or disposed of in a responsible manner. Our packaging is designed to be recycled and should be handled in accordance with your local recycling policies. Product Reclamation and Recycling Program...
  • Page 83 Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899, 6,552,918, 6,567,902, 6,578,186, and 6,590,785.

This manual is also suitable for:

E120E320

Table of Contents