Cisco 15454-TCC - Network Processor Card Operation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Software
  5. 15454-TCC - Network Processor Card
  6. Operation manual
Cisco 15454-TCC - Network Processor Card Operation Manual

Cisco 15454-TCC - Network Processor Card Operation Manual

User guide
Hide thumbs Also See for 15454-TCC - Network Processor Card:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Manual
Installing ONS 15454 SDH TCC-I Cards
Product Name: 15454E-TCC-I=
This document contains a description of TCC-I card features, installation procedures, removal
instructions, and technical specifications. Use this document in conjunction with the Cisco ONS 15454
SDH Installation and Operations Guide and the Cisco ONS 15454 SDH Troubleshooting and Reference
Guide when working with TCC-I cards.
This document contains the following sections:
"TCC-I Timing Communication and Control Card Description" section on page 2
•
"TCC-I Card Specifications" section on page 5
•
"Installation Procedures" section on page 6
•
"Removal Procedures" section on page 7
•
•
"Related Documentation" section on page 9
"Obtaining Documentation and Submitting a Service Request" section on page 10
•
This document contains the following procedures:
"Installation Procedures" procedure on page 6
"Card Turn Up" procedure on page 7
"Verify Successful Turn Up of the TCC-I Card" procedure on page 7
"Removal Procedures" procedure on page 7
"Initiate a Software Reset" procedure on page 8
For information about circuits and card capacities, see the Cisco ONS 15454 SDH Installation and
Note
Operations Guide.
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2002. Cisco Systems, Inc. All rights reserved.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 15454-TCC - Network Processor Card and is the answer not in the manual?

Questions and answers

Related Manuals for Cisco 15454-TCC - Network Processor Card

Summary of Contents for Cisco 15454-TCC - Network Processor Card

  • Page 1 “Verify Successful Turn Up of the TCC-I Card” procedure on page 7 “Removal Procedures” procedure on page 7 “Initiate a Software Reset” procedure on page 8 For information about circuits and card capacities, see the Cisco ONS 15454 SDH Installation and Note Operations Guide.
  • Page 2 TCC-I Timing Communication and Control Card Description TCC-I Timing Communication and Control Card Description The TCC-I performs system initialization, provisioning, alarm reporting, maintenance, diagnostics, IP address detection/resolution, SDH SOH Data Communications Channel (DCC) termination, and system fault detection for the ONS 15454 SDH. The TCC-I also ensures that the system maintains Stratum 3 E (G.813) timing requirements.
  • Page 3 TCC-I Timing Communication and Control Card Description Figure 2 TCC-I block diagram Flash 10BaseT Processor Modem Ethernet Timing Flash Controller 10BaseT Control Processor Craft Framer/ Message TDM/SCC Mux Router Crossconnect TCC-I Functionality The TCC-I supports multichannel, high-level data link control (HDLC) processing for the DCC. Up to 48 DCCs can be routed over the TCC-I and up to ten DCCs can be terminated at the TCC-I (subject to available optical digital communication channels).

  • Page 4: Network-Level Indicators

    MIC-C/T/P unit. Note Cisco does not support operating the ONS 15454 SDH with only one TCC-I card. For full functionality and to safeguard your system, always operate in a redundant configuration. CTC software does not monitor for the presence or absence of FMECs unless the TCC-I(s) card has Note reached the active/standby state.
  • Page 5 TCC-I Timing Communication and Control Card Description Table 2 TCC-I System-Level Indicators System-Level LEDs Definition Red CRIT LED Used to indicate critical alarms in the network at the local terminal. Red MAJ LED Used to indicate major alarms in the network at the local terminal. Yellow MIN LED Used to indicate a minor alarm in the network at the local terminal.

  • Page 6: Installation Procedures

    Installation Procedures Installation Procedures Use this section if you are installing or removing the TCC-I card for the first time. After you become familiar with ONS 15454 SDH card installation and boot up, use this section as a reference. Caution Always use the supplied electrostatic discharge (ESD) wristband when working with an ONS 15454 SDH.

  • Page 7: Removal Procedures

    Removal Procedures Card Turn Up Follow the steps in this section to verify card turn up. If one or more of the Cisco Transport Controller (CTC) software screen conditions according to “Verify Successful Turn Up of the TCC-I Card” section on page 7 are not met, re-install the card.
  • Page 8 Removal Procedures To determine whether the TCC-I card is in active mode or standby mode, view it in the CTC software Note and position the cursor over the TCC-I card graphic to display the status. If you need to perform a card pull on an active TCC-I card, initiate a software reset on the active TCC-I Step 1 card first.

  • Page 9: Related Documentation

    Related Documentation Related Documentation DOC-7813038= Cisco ONS 15454 SDH Installation and Operations Guide • DOC-7813037= Cisco ONS 15454 SDH Troubleshooting and Reference Guide • Installing ONS 15454 SDH TCC-I Cards 78-14610-01...

  • Page 10: Obtaining Documentation And Submitting A Service Request

    CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco...

Table of Contents