Huawei UPS5000-E-300K-SM Quick Manual

UPS5000-E-300K-SM
(50 kVA Power Modules)
Quick Guide
Issue: 12
Date: 2025-01-15
Copyright © Huawei Digital Power Technologies Co., Ltd. 2025. All rights reserved.
Installation Preparation
• Before installing the equipment, read the product documentation carefully to get familiar with
product information and safety precautions. Equipment damage caused by failure to abide by
the storage, transportation, installation, and operation guidelines specified in the product
documentation is not covered by the product warranty. Log in to the technical support website
to view the product documentation and safety precautions.
• The information in this document is subject to change without notice. Every effort has been
made in the preparation of this document to ensure accuracy of the contents, but all
statements, information, and recommendations in this document do not constitute a warranty
of any kind, express or implied.
• Only qualified personnel are allowed to perform operations on the equipment. Operation
personnel should understand the system, its working principles, and relevant national/regional
standards.
• Wear dedicated personal protective equipment during operations. Use dedicated insulated tools
during electrical operations.
Environment requirements
440 kg
Operating Relative humidity
Floor and support
The equipment
temperature 0%–95% RH
load capacity
room is airtight.
0–40°C (non-condensing)
Heat source, Dust or
Water source,
inflammable or Direct sunlight conductive
water vapor
explosive article metal dust
Clearance
Unit: mm
Recommended Circuit Breaker Specifications for
a 380 V AC/400 V AC/415 V AC Voltage System
When the Short-circuit Current Going Through the Device
Capacity
300 kVA
250 kVA
200 kVA
150 kVA
100 kVA
50 kVA
Recommended Cable Specifications for
a 380 V AC/400 V AC/415 V AC Voltage System (mm
Capacity Mains Input
L1: 2×150
L2: 2×150
L3: 2×150
300 kVA
N: 2×150
PE: 150
L1: 2×120
L2: 2×120
L3: 2×120
250 kVA
N: 2×120
PE: 120
L1: 2×95
L2: 2×95
L3: 2×95
200 kVA
N: 2×95
PE: 95
L1: 2×70
L2: 2×70
L3: 2×70
150 kVA
Excessive N: 2×70
salt content PE: 70
L1: 70
L2: 70
L3: 70
100 kVA
N: 70
PE: 35
L1: 25
Volatile or
L2: 25
corrosive
L3: 25
50 kVA
substance
N: 25
PE: 25
Is Less than 36 kA
Mains Input Bypass Input Output
630 A/3P 630 A/3P 630 A/3P
630 A/3P 400 A/3P 400 A/3P
400 A/3P 400 A/3P 400 A/3P
320 A/3P 250 A/3P 250 A/3P
250 A/3P 160 A/3P 160 A/3P
160 A/3P 100 A/3P 100 A/3P
2 )
Equipotential
Bypass Input Output Battery Input
Ground
L1: 2×150 U: 2×150
+: 2×185
L2: 2×150 V: 2×150
N: 2×185
L3: 2×150 W: 2×150
GND：16
-: 2×185
N: 2×150 N: 2×150
PE: 185
PE: 150 PE: 150
L1: 2×120 U: 2×120
+: 2×150
L2: 2×120 V: 2×120
N: 2×150
L3: 2×120 W: 2×120
GND：16
-: 2×150
N: 2×120 N: 2×120
PE: 150
PE: 120 PE: 120
L1: 2×95 U: 2×95
+: 2×120
L2: 2×95 V: 2×95
N: 2×120
L3: 2×95 W: 2×95
GND: 16
-: 2×120
N: 2×95 N: 2×95
PE: 120
PE: 95 PE: 95
L1: 2×70 U: 2×70
+: 2×95
L2: 2×70 V: 2×70
N: 2×95
L3: 2×70 W: 2×70
GND: 16
-: 2×95
N: 2×70 N: 2×70
PE: 95
PE: 70 PE: 70
U: 70
L1: 70
+: 95
V: 70
L2: 70
N: 95
L3: 70
W: 70
GND: 16
–: 95
N: 70
N: 70
PE: 50
PE: 35
PE: 35
L1: 25 U: 25
+: 35
L2: 25 V: 25
N: 35
L3: 25 W: 25
GND: 16
–: 35
N: 25 N: 25
PE: 35
PE: 25 PE: 25
1
Installing a Cabinet
Secured Installation
1
Determine the UPS cabinet installation position. Draw mounting holes in the
installation position according to the drawing.
Unit: mm
2
Drill holes in the mounting holes using a hammer drill, and install expansion bolts
in the holes.
M12 bolt
Spring washer
Flat washer
Concrete floor
Expansion sleeve
Expansion nut
3
Move the cabinet to the installation position. Remove the rear panel of the
cabinet, and then open the front door.