Otto Bock Motus CV Instructions For Use Manual

Hide thumbs Also See for Motus CV:

Instructions for use manual (80 pages)

Instructions for use manual (36 pages)

Instructions for use manual (52 pages)

page of 40

/ 40
Bookmarks

Quick Links

Download this manual

Motus CV, Motus CS,

Motus Hemi, Motus XXL

Instructions for use (qualified personnel) .................................................................

Need help?

Do you have a question about the Motus CV and is the answer not in the manual?

Questions and answers

Summary of Contents for Otto Bock Motus CV

Page 1 Motus CV, Motus CS, Motus Hemi, Motus XXL Instructions for use (qualified personnel) ..............
Page 2 Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 3 ............Adjusting the side panels ........................6.8.1 Installing and adjusting the swivel unit and forearm supports ..............Adjusting the anti-tipper ........................6.10 Adjusting the lap belt ........................... 6.11 Adjusting the tray ..........................Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 4 Information on re-use ........................... Legal information .............................. 10.1 Liability .............................. 10.2 Warranty ............................10.3 Lifetime .............................. Technical data ..............................Appendices ................................ 12.1 Required tools ............................ 12.2 Torque values of the screw connections ....................Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 5 3 Safety 3.1 Explanation of warning symbols Warning regarding possible serious risks of accident or injury. WARNING Warning regarding possible risks of accident or injury. CAUTION Warning regarding possible technical damage. NOTICE Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 6 4 Delivery 4.1 Scope of delivery • Preassembled wheelchair • Two drive wheels (installed or included) • Options according to the order • Instructions for use (qualified personnel), instructions for use (user) Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 7 5) If necessary: Attach the leg supports. Fold the foot plate(s) down. With a single-panel foot plate, make sure the support of the foot plate is locked into the receiver. 6) If necessary: Secure the seat cushion against sliding by pressing it onto the hook-and-loop closure. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 8 ► Always replace self-locking screws and nuts with new self-locking screws and nuts after disassembly. Fine-tuning and adjustments should always be carried out in the presence of the user. The user should be sitting upright in the wheelchair while making adjustments. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 9 → Tracking of the drive wheels (see page 12) → Height and alignment of the caster attachment device (see page 14) → Adjustment of the brakes (see page 16) → Distance of the side panels to the drive wheels (see page 28) Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 10 1) Remove the wheels. 2) Loosen the hexagon nuts (see fig. 6, item 1) on both sides of the quick-release axle mounting (see fig. 6, item 2) and remove the quick-release axle mounting with the spacers. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 11 (see fig. 9, item 3). 5) Slide the supplied assembly aid (spirit level) (see fig. 10, item 1) onto the quick-release axle with the drive wheel and insert the quick-release axle into the quick-release axle mounting. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 12 ► The caster wheel journal angle should be checked immediately after every adjustment to the track (see page 14). 1) Slightly loosen the hexagon nuts (see fig. 12, item 1) on the quick-release axle mounting. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 13 All handrims are designed for a spacing from the drive wheel of 15 mm (standard setting) and 25 mm (see fig. 14). 1) Loosen/remove the handrim screw connections from the rim. 2) Tightly screw the handrims onto the rim in narrow or wide installation position (see fig. 15). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 14 7) Firmly tighten the hexagon socket screws on the inside of the frame. 8) Attach the protective cap to the caster wheel adapter. → The threaded axle on each of the two caster wheel adapters must be positioned vertically. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 15 → Once adjusted, the left and right caster wheels must have the same vertical position in the caster fork. → After changing the front seat height, always check the caster wheel journal angle and adjust it if necessary (see page 14). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 16 → It must not be possible to push the wheelchair with the wheel locks engaged. 4) Tighten the hexagon socket screws to 15 Nm (see fig. 24, item 1). → After adjustment, the left and right scissor wheel locks must both have the same braking force. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 17 → The wheel lock bolt must lock the drive wheel securely when stationary. 5) If necessary: Shorten the Bowden cable to 10 mm after making the adjustments and attach a cable end cap (not illustrated). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 18 After making adjustments, check that activating the manual brake lever creates a sufficient braking effect. Note that the drum brake must still be able to produce sufficient braking force even when the manual brake lever is locked into a ratchet position. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 19 5) Insert the mounting screws into the frame tube and tighten to 7 Nm. → Both back support tubes must be adjusted to the same height. Properly reassemble all components upon completion of the adjustments. To adjust the back support upholstery: see page 21. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 20 With an anatomically shaped rigid back plate made of aluminium, the back system enables the best possible posi tioning. Large openings in the back shells provide for a low weight and easy handling. Detailed information regarding use, cleaning and maintenance can be found in the included instructions for use. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 21 (see fig. 44, item 1), trim the upholstery straps (see fig. 44, item 2) and reattach the end pieces. 5) Put on the back support pad and attach it with the hook-and-loop fastener. Make sure the fold lies flush over the upper edge of the back support (see fig. 45). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 22 2) Attach the back support tubes. Tighten the Allen screws to 7 Nm. 3) Tighten the Allen screws between the back support upholstery and the back support tubes to 2 Nm. 4) Fasten the hook-and-loop closures on the back support upholstery. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 23 6) Replace the caps and insert them into the frame tubes using a soft-faced hammer. 7) Unfold the wheelchair. The crossbrace must be seated fully in the supports as you do so. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 24 40 mm into the leg support holder. INFORMATION: A mark on the foot plate bar indicates the minimum distance the foot plate bar must be inserted during installation. 3) Tighten the hexagon socket screw to 7 Nm. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 25 2) Turn the foot plate to the desired angle. 3) Tighten the hexagon socket screw to 8 Nm. Segmented plastic foot plate 1) Loosen the Allen screw on the foot plate suspension (see fig. 57). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 26 1) Loosen the hexagon socket screws on the leg support (see fig. 60, item 1). 2) Turn the foot plate to the desired angle (see fig. 60, item 2). 3) Tighten the hexagon socket screws to 9 Nm. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 27 2) Depth adjustment:Loosen and remove the Allen head screw on the posterior lower leg pad: (see fig. 65, item 1). Move the posterior lower leg pad to one of the 4 possible positions (see fig. 65, item 2) and firmly retighten the Allen head screw. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 28 INFORMATION: Align the side panels downward. 5) Tighten the mounting screws. 6) Attach the drive wheel and check the freewheel. → After adjustment, the side panels have to be aligned the same on both sides. Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 29 4) Removing the side panel: Pull the side panel release lever back (see fig. 74, item 1) and fold the side panel up by about 90° (see fig. 74, item 2). Turn the side panel towards the back support (see fig. 75, item 1) and pull it out of the side panel mounting (see fig. 75, item 2). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 30 Assembly is described in more detail in the instructions for use supplied with the swivel unit – reference number 647H564=ALL_INT. Adjusting the swivel unit with arm support is described in more detail in the supplied instructions for use (user). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 31 ► Adjusting the belt system too loosely can cause the user to slide into a dangerous position. In addition, the fastening buckles could open unintentionally if they slide against hard parts of clothing (e.g. buttons). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 32 8 Maintenance and repair The manufacturer recommends regular maintenance of the product every 12 months. Further information on caring for the product and on maintenance/repair can be found in the instructions for use (user). Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 33 ► Note that not all adjustment possibilities can be used with all product versions. Furthermore, the adjustment combinations are limited by the compact frame geometry. ► Technical changes and tolerances are reserved by the manufacturer. Motus Max. load (with double crossbrace) [kg] 125 (140) Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 34 < 400 mm 24" with front seat height ≥ 410 mm or with rear seat height ≥ 400 mm Caster wheels 4", 5", 5.5", 6", 7" Permissible tyre type Pneumatic, PU or solid rubber / 1", 1 3/8" Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 35 Unless otherwise specified, screw connections are tightened with the following torque values: • Thread diameter M4: 3 Nm • Thread diameter M5: 5 Nm • Thread diameter M6: 8 Nm • Thread diameter M8: 20 Nm Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 36 Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 37 Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 38 Motus CV, Motus CS, Motus Hemi, Motus XXL...
Page 40 Ihr Fachhändler | Your specialist dealer Otto Bock Mobility Solutions GmbH Lindenstraße 13 · 07426 Königsee/Germany www.ottobock.com...

This manual is also suitable for:

Motus cs Motus hemi Motus xxl