Analog Devices ADSP-BF527 EZ-KIT Lite Manual
  1. Manuals
  2. Brands
  3. Analog Devices Manuals
  4. Motherboard
  5. Lite ADSP-BF527 EZ-KIT
  6. Manual
Analog Devices ADSP-BF527 EZ-KIT Lite Manual

Analog Devices ADSP-BF527 EZ-KIT Lite Manual

Evaluation system
Hide thumbs Also See for ADSP-BF527 EZ-KIT Lite:
Table of Contents

Advertisement

Quick Links

Download this manual
ADSP-BF527 EZ-KIT Lite
®
Evaluation System Manual
Revision 1.7, July 2012
Part Number
82-000208-01
Analog Devices, Inc.
One Technology Way
a
Norwood, Mass. 02062-9106
Arrow.com.
Downloaded from

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ADSP-BF527 EZ-KIT Lite and is the answer not in the manual?

Questions and answers

Related Manuals for Analog Devices ADSP-BF527 EZ-KIT Lite

Summary of Contents for Analog Devices ADSP-BF527 EZ-KIT Lite

  • Page 1 ADSP-BF527 EZ-KIT Lite ® Evaluation System Manual Revision 1.7, July 2012 Part Number 82-000208-01 Analog Devices, Inc. One Technology Way Norwood, Mass. 02062-9106 Arrow.com. Downloaded from...

  • Page 2: Copyright Information

    Analog Devices, Inc. Printed in the USA. Disclaimer Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use;...

  • Page 3: Regulatory Compliance

    Regulatory Compliance The ADSP-BF527 EZ-KIT Lite is designed to be used solely in a labora- tory environment. The board is not intended for use as a consumer end product or as a portion of a consumer end product. The board is an open system design which does not include a shielded enclosure and therefore may cause interference to other electrical devices in close proximity.
  • Page 4 Arrow.com. Downloaded from...

  • Page 5: Table Of Contents

    Related Documents ................. xx Notation Conventions ..............xxi USING THE ADSP-BF527 EZ-KIT LITE Package Contents ................1-3 Default Configuration ..............1-3 CCES Install and Session Startup ..........1-4 Session Startup ................ 1-6 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 6 USB OTG Interface ..............1-25 UART Interface ................1-26 RTC Interface ................1-27 LEDs and Push Buttons .............. 1-27 JTAG Interface ................1-28 Expansion Interface ..............1-29 Power Measurements ..............1-29 Power-On-Self Test ..............1-30 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 7 SPI/TWI Switch (SW19) ............2-19 SPORT0A ENBL Switches (SW20 and SW27) ...... 2-19 TFS0A/HOSTCE Enable Switch (SW21) ......2-19 Touch ADD Switch (SW22) ..........2-19 Touchpad INT Switch (SW24) ..........2-20 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 8 Ethernet LEDs (LED6–7) ............. 2-27 Keypad Current Sink LED (LED8) ........2-27 Connectors ................. 2-28 Expansion Interface Connectors (J1–3) ........2-28 DCE (RS-232) Connector (J4) ..........2-29 Battery Holder (J5) ............... 2-29 viii ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 9 CPLD JTAG Connector (P17) ..........2-34 LCD Data Connector (P18) ..........2-34 USB Debug Agent Connector (ZJ1) ........2-35 JTAG Connector (ZP4) ............2-35 ADSP-BF527 EZ-KIT LITE BILL OF MATERIALS ADSP-BF527 EZ-KIT LITE SCHEMATIC INDEX ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com.
  • Page 10 Contents ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 11 PREFACE ® Thank you for purchasing the ADSP-BF527 EZ-KIT Lite , Analog ® Devices, Inc. evaluation system for Blackfin processors. Blackfin processors embody a type of embedded processor designed specif- ically to meet the computational demands and power constraints of today’s embedded audio, video, and communications applications.
  • Page 12 ADSP-BF527 processor and evaluation board peripherals. Analog Devices JTAG emulators offer faster communi- cation between the host PC and target hardware. Analog Devices carries a wide range of in-circuit emulation products. To learn more about Analog Devices emulators and processor development tools, go to http://www.analog.com/dsp/tools...

  • Page 13: Preface

    • ST Micro M25P16 – 16 Mb • Internal audio codec • Low-power audio codec • One stereo jack LINE OUT • One input jack • One input stereo jack LINE IN ADSP-BF527 EZ-KIT Lite Evaluation System Manual xiii Arrow.com. Downloaded from...
  • Page 14 Product Overview • TFT LCD display with touchscreen • Sharp LQ035Q1DH02 320 x 240 3.5’’ touchscreen LCD • Analog Devices AD7879-1 four-wire touchscreen controller • Ethernet interface • SMSC LAN8700 PHY device • 10-BaseT and 100-BaseTX Ethernet controller • Auto-MDIX •...

  • Page 15: Purpose Of This Manual

    “ADSP-BF527 EZ-KIT Lite Hardware Reference” on page 2-1. Purpose of This Manual The ADSP-BF527 EZ-KIT Lite Evaluation System Manual provides instructions for installing the product hardware (board). The text describes operation and configuration of the board components and pro- vides guidelines for running your own code on the ADSP-BF527 EZ-KIT Lite.

  • Page 16: Intended Audience

    Intended Audience Intended Audience The primary audience for this manual is a programmer who is familiar with Analog Devices processors. This manual assumes that the audience has a working knowledge of the appropriate processor architecture and instruction set. Programmers who are unfamiliar with Analog Devices processors can use this manual but should supplement it with other texts that describe your target architecture.

  • Page 17: What's New In This Manual

    Manual. The manual has been updated to include CCES information. In addition, modifications and corrections based on errata reports against the previous manual revision have been made. For the latest version of this manual, please refer to the Analog Devices Web site. Technical Support...

  • Page 18: Supported Processors

    ADSP-BF525 processors can be evaluated using the same product because the processors have many similarities. Product Information Product information can be obtained from the Analog Devices Web site and the online help system. Analog Devices Web Site The Analog Devices Web site, , provides information www.analog.com...
  • Page 19 Also note, is a free feature of the Analog Devices Web site that myAnalog allows customization of a Web page to display only the latest information about products you are interested in.

  • Page 20: Engineerzone

    Related Documents EngineerZone EngineerZone is a technical support forum from Analog Devices. It allows you direct access to ADI technical support engineers. You can search FAQs and technical information to get quick answers to your embedded processing and DSP design questions.

  • Page 21: Notation Conventions

    A Warning identifies conditions or inappropriate usage of the product that could lead to conditions that are potentially hazardous for the devices users. In the online version of this book, the word Warning appears instead of this symbol. ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 22 Notation Conventions xxii ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 23 1 USING THE ADSP-BF527 EZ-KIT LITE This chapter provides information to assist you with development of pro- grams for the ADSP-BF527 EZ-KIT Lite evaluation system. The following topics are covered. • “Package Contents” on page 1-3 • “Default Configuration” on page 1-3 •...
  • Page 24 EZ-KIT Lite system, refer to the online help. For more detailed information about the ADSP-BF527 Blackfin proces- sor, see documents referred to at “Related Documents”. ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 25: Using The Adsp-Bf527 Ez-Kit Lite

    Store unused EZ-KIT Lite boards in the protective shipping package. The ADSP-BF527 EZ-KIT Lite board is designed to run outside your per- sonal computer as a standalone unit. You do not have to open your computer case.

  • Page 26: Cces Install And Session Startup

    Figure 1-1. EZ-KIT Lite Hardware Setup CCES Install and Session Startup For information about CCES and to download the software, go to . A link for the ADSP-BF527 EZ-KIT Lite Board www.analog.com/CCES Support Package (BSP) for CCES can be found at http://www.analog.com/Blackfin/EZKits...
  • Page 27 Using the ADSP-BF527 EZ-KIT Lite Step 1: Connect the EZ-KIT Lite board to a personal computer (PC) run- ning CCES using one of two options: an Analog Devices emulator or via the debug agent. Using an Emulator: 1. Plug one side of the USB cable into the USB connector of the emu- lator.

  • Page 28: Session Startup

    • Choose Run > Debug Configurations. The Debug Configuration dialog box appears. 3. Select CrossCore Embedded Studio Application and click (New launch configuration). The Select Processor page of the Session Wizard appears. ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 29 The Select Platform page of the Session Wizard appears. 6. Do one of the following: • For standalone debug agent connections, ensure that the selected platform is ADSP-BF527 EZ-KIT Lite via Debug Agent. • For emulator connections, choose the type of emulator that is connected to the board.

  • Page 30: Visualdsp++ Install And Session Startup

    For information about VisualDSP++ and to download the software, go to www.analog.com/VisualDSP  There are two USB interfaces on the ADSP-BF527 EZ-KIT Lite. Be sure to use the debugger’s interface ( ) when connecting your computer to the board with provided USB cable. The other USB interface (labelled ) is for applications use.
  • Page 31 Select EZ-KIT Lite and click Next. 6. The Select Platform page of the wizard appears on the screen. Ensure that the selected platform is ADSP-BF527 EZ-KIT Lite via Debug Agent. Specify your own Session name for the session or accept the default name.

  • Page 32: Cces Evaluation License

    Delete. Click OK. CCES Evaluation License The ADSP-BF527 EZ-KIT Lite software is part of the Board Support Package (BSP) for the Blackfin ADSP-BF52x family. The EZ-KIT Lite is a licensed product that offers an unrestricted evaluation license for 90 days after activation.

  • Page 33: Visualdsp++ Evaluation License

    CCES with a valid evaluation or full license. VisualDSP++ Evaluation License The ADSP-BF527 EZ-KIT Lite installation is part of the VisualDSP++ installation. The EZ-KIT Lite is a licensed product that offers an unre- stricted evaluation license for the first 90 days. Once the initial unrestricted 90-day evaluation license expires: •...

  • Page 34: Memory Map

    ADSP-BF2x Blackfin Processor Hard- ware Reference. The ADSP-BF527 EZ-KIT Lite board includes four types of external memory: synchronous dynamic random access memory (SDRAM), serial peripheral interconnect (SPI), parallel flash, and NAND flash. See Table 1-2.
  • Page 35 0xFFA0 0000 L1 INSTRUCTION BANKA UPPER SRAM (16K BYTE) 0xFFA0 4000 L1 INSTRUCTION BANKB LOWER SRAM (16 BYTE) 0xFFA0 8000 Reserved 0xFFA0 C000 L1 INSTRUCTION SRAM/CACHE (16K BYTE) 0xFFA1 0000 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-13 Arrow.com. Downloaded from...
  • Page 36 ASYNC memory bank 1 (flash) 0x2010 0000 0x201F FFFF ASYNC memory bank 2 (flash) 0x2020 0000 0x202F FFFF ASYNC memory bank 3 (flash) 0x2030 0000 0x203F FFFF Reserved 0xEEFF FFFF 0x2040 0000 1-14 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 37: Sdram Interface

    Calculated with = 133 MHz pEBIU_SDRRC 0x0407 SCLK = 133 MHz fSCLK = 64 ms tREF = 8192 row addresses = 6 clock cycles tRAS = 2 clock cycles RDIV 0x407 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-15 Arrow.com. Downloaded from...
  • Page 38 An example program is included in the EZ-KIT Lite installation directory to demonstrate how to setup and access the SDRAM interface. For more information on how to initialize the registers after a reset, search the online help for “reset values”. 1-16 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 39: Parallel Flash Memory Interface

    Using the ADSP-BF527 EZ-KIT Lite Parallel Flash Memory Interface The parallel flash memory interface of the ADSP-BF527 EZ-KIT Lite contains a 4 MB (2M x 16 bits) ST Micro M29W320EB chip. Flash memory is connected to the 16-bit data bus and address lines 1 through 19.

  • Page 40: Spi Interface

    By default, the LCD is setup to use . The LCD optionally can use SPISEL7 by setting appropriately. For more information, SPISEL1 SPISEL5 SW25 refer to “LCD/KPAD CTL Switch (SW25)” on page 2-20. 1-18 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 41: Ppi Interface

    320 x 240 pixels and a color depth of 16 bits. By default, the interface is an RGB-888 serial parallel interface, eight bits of red, followed by eight bits of green, and then eight bits of blue. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-19 Arrow.com.
  • Page 42 “LCD Reset Switch (SW5)” on RESET page 2-13 for more information. The verilog source code for the CPLD can be found in the reference resource zip file in the folder of the installation. Examples 1-20 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 43: Touchscreen Interface

    LED8 pin of the ADP5520 controller ( ILED An example program is included in the EZ-KIT Lite installation directory to demonstrate how to setup and access the keypad interface. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-21 Arrow.com. Downloaded from...

  • Page 44: Rotary Encoder Interface

    10BASE-T and 100BASE-TX operations. The part is attached gluelessly to the processor. The Ethernet signals are shared with NAND flash. By default, Ethernet is turned off ( ). See “ETH Enable Switch (SW1)” on SW1 OFF 1-22 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 45: Audio Interface

    Ethernet and host connectors, as well TFS0A as the signals. allows this signal to be dis- RMIIMDINT# HOSTCE# SW21 connected from the host connector by setting position 1 , and STAMP ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-23 Arrow.com. Downloaded from...
  • Page 46 3 and 4 are For testing purposes, positions 1 and 2 allow the signal to be MICIN connected to either the left or right headphone. Do not connect both left 1-24 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 47: Usb Otg Interface

    ); cables that plug into are shipped with the EZ-KIT Lite. Use example programs in the EZ-KIT Lite installation directory to learn about the ADSP-BF527 processor’s device and host modes. For more ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-25 Arrow.com. Downloaded from...

  • Page 48: Uart Interface

    (UARTs). share the processor pins with UART1—0 other peripherals on the EZ-KIT Lite. has full RS-232 functionality via the Analog Devices 3.3V UART1 ADM3202 line driver and receiver ( ). The UART can be disconnected from the ADM3202 device by turning all positions of .

  • Page 49: Rtc Interface

    , are accessed via the LED1 LED3 PG11 pins of the processor, respectively. For information on how to PG12 program the pins, refer to the ADSP-BF52x Blackfin Processor Hardware Reference. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 1-27 Arrow.com. Downloaded from...

  • Page 50: Jtag Interface

    JTAG connector ( ). When an external emulator connects to the board, the on-board USB debug agent is disabled. See “JTAG Connector (ZP4)” on page 2-35 for more information. 1-28 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 51: Expansion Interface

    Using the ADSP-BF527 EZ-KIT Lite For more information about emulators, contact Analog Devices or go to: http://www.analog.com/processors/tools/blackfin Expansion Interface The expansion interface consists of three 90-pin connectors ( ). These J1—3 connectors contain a majority of the ADSP-BF527 processor’s signals. For the pinout of the connectors, go to “ADSP-BF527 EZ-KIT Lite Sche-...

  • Page 52: Power-On-Self Test

    Note that the source code for the POST program is included in the EZ-KIT Lite installation directory along with the readme file, which describes how the board is configured to run POST.  The POST program is only available when using VisualDSP++. 1-30 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 53: Example Programs

    Using the ADSP-BF527 EZ-KIT Lite Example Programs Example programs are provided with the ADSP-BF527 EZ-KIT Lite to demonstrate various capabilities of the product. The programs are included in the product installation kit and can be found in the Examples folder of the installation. Refer to a readme file provided with each exam- ple for more information.
  • Page 54 Board Design Database 1-32 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 55: Adsp-Bf527 Ez-Kit Lite Hardware Reference

    Lite board. The following topics are covered. • “System Architecture” on page 2-2 Describes the ADSP-BF527 EZ-KIT Lite board configuration and explains how the board components interface with the processor. • “Programmable Flags” on page 2-3 Shows the locations and describes the programming flags (PFs).

  • Page 56: System Architecture

    The EZ-KIT Lite is designed to demonstrate the ADSP-BF527 processor capabilities. The processor has an I/O voltage of 3.3V. The core voltage of the processor is controlled by the internal voltage regulator. ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 57: Programmable Flags

    J1.73 PPI connector via P8.9 Default: LCD via CPLD. PPID2/RSCLK0/ND_D2 Expansion interface via J1.74 PPI connector via P8.10 Default: LCD via CPLD. PPID3/DT0PRI/ND_D3A Expansion interface via J1.75 PPI connector via P8.11 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 58 PPI connector P8.18 Default: rotary ( ) via PF11 PPID11/TFS1/CZM SW11.3 LCD via CPLD and SW29 Expansion interface via J2.32 J2.50 Via a quick switch to PPI connector P8.19 SPORT1 connector P7.11 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 59 ) CS via SPISS#/SPISEL1# SW9.4 LCD CS via , expansion interface , via SW25.2 J2.11 quick switch to the following connectors: SPI , PPI , SPORT0 , and SPORT1 P9.10 P8.27 P6.17 P7.17 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 60 SPORT0 , SPORT1 , timers P6.32 P6.16 P7.32 , and expansion interface P11.10 J2.41 Default: SPORT0 audio codec ( ) via PG10 TMR6/TSCLK0A/TACI6 SW23.1 SPORT0 connector , expansion interface P6.6 J2.42 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 61 0 ( ), and expansion interface P13.31 J3.40 Default: NAND Data 1 ( ND_D1/ERXER/HOST_D1 PHY receive error ( ), host connector data 1 U14.21 ), expansion interface ( P13.29 J3.39 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 62 PH10 ND_CE#_ERXD2/HOST_D10 SW11.4 ON Host connector data 10 ( ), expansion interface P13.17 J3.35 Default: NAND write enable ( PH11 ND_WE/ETXD3/HOST_D11 Host connector data 11 ( ), expansion interface P13.9 J3.14 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 63 , expansion interface ( ), the fol- SW19.4 J2.58 lowing connectors via a quick switch ( ): TWI ), PPI ( ), SPORT0 ( ), and SPORT1 P10.6 P8.36 P6.24 P7.24 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 64: Push Buttons And Switches

    3 enables the MDIO 50 MHz clock. position 4 holds the PHY in reset (set to ) or RMII connects the PHY reset to the EZ-KIT Lite reset (set to 2-10 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 65: Boot Mode Select Switch (Sw2)

    Boot from serial TWI memory Boot from TWI host Boot from UART0 host Boot from UART1 host Reserved Boot from SDRAM Reserved Boot from 8-bit NAND flash PORTF Boot from 8-bit NAND flash PORTH ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-11 Arrow.com. Downloaded from...

  • Page 66: Rotary Encoder With Momentary Switch (Sw3)

    . Refer to “Audio Interface” on page 1-23 for more information about the audio codec. Table 2-7. MIC Gain Switch (SW4) Gain SW4 Switch Settings 5 (14 dB) 1 (0 dB) 2-12 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 67: Lcd Reset Switch (Sw5)

    Table 2-9 that is turned , the size of available flash memory is reduced by 1 MB. Table 2-9. Flash Enable Switch (SW7) SW7 Switch Position (Default) Processor Signal AMS0 AMS1 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-13 Arrow.com. Downloaded from...

  • Page 68: Mic/Hp Lpbk Audio Mode Switch (Sw8)

    SPI flash chip ( ). Setting SPISEL1 position 4 is useful when using on the expansion inter- SPISEL1 face at connector pin 11. By default, position 4 is 2-14 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 69: Uart Enable Switch (Sw10)

    Table 2-11. UART Enable Switch (SW10) From Default Alternate Function Ties SW10.1 HWAIT_PUSHBUTTON1 T2IN URT1RTS T2IN Disconnects SW10.2 UART1RX PF15 UART1RX flow control signal SW10.3 UART1CTS_LCDSPICS PF10 R2OUT Loopback of SW10.4 R2OUT T2IN ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-15 Arrow.com. Downloaded from...

  • Page 70: Rotary Nand Enable Switch (Sw11)

    ), STAMP PF12 J2.30 J2.51 buffer ( Encoder Processor Expansion interface ( ), STAMP buf- J2.32 J2.50 fer ( PF11 Processor NAND Host connector ( ), expansion interface P13.11 PH10 J3.35 2-16 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 71: Gpio Enable Switch (Sw13)

    SW13 PG13 programmable flag pin of the processor can be used to control the 5V reg- ulator ( ). Refer to “USB OTG Interface” on page 1-25 for more information. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-17 Arrow.com. Downloaded from...

  • Page 72: Programmable Flag Push Buttons (Sw14-15)

    USB cable has been plugged in and communication with the PC has been initialized correctly. After USB communication has been initialized, the only way to reset the USB chip is by powering down the board. 2-18 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 73: Spi/Twi Switch (Sw19)

    C address of the SW22 AD7879-1 controller ( ) as shown in Table 2-14. Table 2-14. AD7879-1 (U37) I C Address Options SW22.1 Setting SW22.2 Setting C Address 0101 100 0101 101 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-19 Arrow.com. Downloaded from...

  • Page 74: Touchpad Int Switch (Sw24)

    ADP5520 keypad controller ( The signal options for the LCD SPI chip select are: • ) on position 1 UART1CTS_LCDSPICS PF10 • ) on position 2 SPISEL1 • ) on position 3. SPISEL5#_HOSTD9 2-20 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 75: Mode Switch (Sw26)

    3, 4, and 5 are not used and available for future use. SW26 SW26 position 6 enables a PPI data buffer between the processor and LCD (active low). By default, SW26 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-21 Arrow.com. Downloaded from...

  • Page 76: Line In-Out Lpbk Switch (Sw28)

    • Positions 3 and 4 disconnect signals from the UART1TX UART1RX DCE (UART) interface. • Positions 5 and 6 disconnect flow control signals from the DCE (UART) interface. By default, SW30 2-22 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 77: Jumpers

    STAMP connectors have a number of nets connected by enabling quick switches at locations , and . When installed, the STAMP enable jumper ( ) enables the quick switches. Table 2-16 lists the ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-23 Arrow.com. Downloaded from...

  • Page 78: Flash Wp Jumper (Jp10)

    Block 70 contains 64 KB of configuration data at address range . When the jumper is installed on 0x203 F0000—0x203 FFFFF , and the parallel flash driver from Analog Devices is used, block 70 is JP10 read-only. By default, is not installed.

  • Page 79: Vddint Power Jumper (P14)

    IDC header. To measure power, remove the jumper and measure voltage across the 0.05 ohm resistor. Once voltage is measured, the power can be calculated. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-25 Arrow.com.

  • Page 80: Leds

    2-17). The LEDs are active high and are lit by writ- ing a to the correct signal. Table 2-17. User LEDs LED Reference Designator Processor Programmable Flag Pin LED1 LED2 PG11 LED3 PG12 2-26 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 81: Power Led (Led4)

    When is lit, it indicates that the master reset of all major ICs is LED5 active. The reset LED is controlled by the Analog Devices ADM708 supervisory reset circuit. You can assert the reset push button ( ) to SW16 assert a master reset and to activate For more information, see “Reset...

  • Page 82: Connectors

    The connectors are located at the bottom of the board. For more information, see “Expansion Interface” on page 1-29. For availability and pricing of the connectors, contact J1—3 Samtec. 2-28 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 83: Dce (Rs-232) Connector (J4)

    2m female-to-female cable DIGI-KEY AE1020-ND Battery Holder (J5) Part Description Manufacturer Part Number 24 mm battery holder KEYSTONE Mating Battery (shipped with EZ-KIT Lite) 3V 280MAH 24 mm LI-COIN SANYO CR2430 ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-29 Arrow.com. Downloaded from...

  • Page 84: Power Connector (J6)

    3.5 mm stereo headphones KOSS 151225 UR5 Ethernet Connector (J9) Part Description Manufacturer Part Number RJ-45 Ethernet jack STEWART SS-6488-NF Mating Cable (shipped with EZ-KIT Lite) Cat 5E patch cable RANDOM PC10/100T-007 2-30 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 85: Usb Otg Connector (P1)

    The pinout of the connector can be found in “ADSP-BF527 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-410HLF Mating Connector IDC socket DIGI-KEY S4205-ND ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-31 Arrow.com. Downloaded from...

  • Page 86: Sport0 Connector (P6)

    The pinout of the connector can be found in “ADSP-BF527 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-440HLF Mating Connector IDC socket DIGI-KEY S4220-ND 2-32 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 87: Spi Connector (P9)

    The pinout of the connector can be found in “ADSP-BF527 EZ-KIT Lite Schematic” on page B-1. Part Description Manufacturer Part Number IDC header 68737-410HLF Mating Connector IDC socket DIGI-KEY S4205-ND ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-33 Arrow.com. Downloaded from...

  • Page 88: Host Interface Connector (P13)

    LCD Data Connector (P18) Part Description Manufacturer Part Number FPC 67PIN CON063 KYOCERA ELCO 046281267212846+ Mating LCD Display Module (shipped with EZ-KIT Lite) 3.5” TFT LCD with touchscreen Sharp LQ035Q1DH02 2-34 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

  • Page 89: Usb Debug Agent Connector (Zj1)

    Pin 3 is missing to provide keying. Pin 3 in the mating connector should have a plug. When using an emulator with the EZ-KIT Lite board, follow the connec- tion instructions provided with the emulator. ADSP-BF527 EZ-KIT Lite Evaluation System Manual 2-35 Arrow.com. Downloaded from...
  • Page 90 Connectors 2-36 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 91 25MHZ EPSON SG-8002CA MP OSC003 SN74LVC1G08 U9-11,U29,U36 SN74LVC1G08DBVR SOT23-5 FDS9431A FAIRCHILD FDS9431A SOIC8 MT48LC32M1 MICRON MT48LC32M16A2P-75 6A2TG-75 TSOP54 SI4411DY SO-8 U18,U23 VISHAY Si4411DY-T1-E3 HX1188 DIGI-KEY 553-1340-ND ICS007 24MHZ EPSON SG-8002CA-MP OSC003 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 92 OSC003 0.000M) ADM708SARZ ANALOG ADM708SARZ SOIC8 DEVICES ADP3336ARM VR3-4 ANALOG ADP3336ARMZ-REEL7 Z MSOP8 DEVICES ADG752BRTZ ANALOG ADG752BRTZ-REEL SOT23-6 DEVICES ADM3202ARN ANALOG ADM3202ARNZ Z SOIC16 DEVICES ADSPBF527KB ANALOG ADSP-BF527KBCZ- CZENGC1 DEVICES MBGA28 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 93 ADSP-BF527 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number ADP1864AUJZ VR1-2 ANALOG ADP1864AUJZ-R7 SOT23-6 DEVICES ADP5520 ANALOG ADP5520ACPZ-RL LFCSP_VQ24 DEVICES AD7879-1 ANALOG AD7879-1ACPZ-RL LFCSP16 DEVICES ADP1613 ANALOG ADP1613ARMZ-R7 MSOP8 DEVICES SWITCH- RAPC712X 2.5MM_JACK CRAFT CON005 .05 45X2...
  • Page 94 MOMEN- SW14-16 PANASONIC EVQ-Q2K03W TARY SWT024 IDC 9X1 SAMTEC SSW-109-01-TM-S IDC9X1 BATT_HOLDE KEYSTONE R 24MM ELEC CON054 FPC 67PIN KYOCERA 046281267212846+ CON063 ELCO 3.5MM J7-8 SWITCH- 35RAPC7JS DUAL_STERE CRAFT O CON066 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 95 ADSP-BF527 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number SJ13 DIGI-KEY 3M9414-ND 2PIN_JUMPER _SHORT IDC 2X1 JP14-15 SAMTEC TMM-101-01-T-D IDC2X1_2MM YELLOW LED1-3,LED6 DIGI-KEY P512TR-ND LED001 22PF 50V 5% C307 08055A220JAT 0805 0.22UF 25V C112,C283-287 08053C224KAT2A 10% 0805 0.1UF 50V 10%...
  • Page 96 10% 0805 0.1UF 10V 10% C12-19,C27-30,C38- 0402ZD104KAT2A 0402 41,C47-50,C56-57, C64-66,C78,C81,C83, C88,C98,C100,C103, C105,C111,C132, C135-136,C146,C157- 158,C160-161,C249, C280,C300-301,C305, C308 0.01UF 16V C2,C4-6,C8-11,C20- 0402YC103KAT2A 10% 0402 21,C23-26,C31-32, C34-37,C42,C44-46, C51,C53-55,C58,C60- 63,C67,C69-77,C79- 80,C82,C84-87,C90- 91,C93,C97,C116-117, C121-127,C137-138, C155-156,C163,C166- 168,C187-188,C248, C250,C306 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 97 ADSP-BF527 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 10K 1/16W 5% R2-3,R11-14,R16-22, VISHAY CRCW040210K0FKED 0402 R24-27,R34,R53-55, R59,R65,R69-70,R73- 76,R89,R91,R104-105, R107,R118-121,R125- 126,R129-131,R140, R144,R157-158,R160, R164,R166,R169,R176- 178,R196,R198,R213, R305,R318,R324-325, R329,R332-333,R335, R342-343,R345,R351 4.7K 1/16W 5% R23,R212 VISHAY CRCW04024K70JNED 0402 0 1/16W 5%...
  • Page 98 VISHAY CRCW0603330RJNEA 0603 1M 1/10W 5% VISHAY CRCW06031M00FNEA 0603 0 1/10W 5% R102,R109,R133,R168, PHYCOMP 232270296001L 0603 R308-309,R334 49.9 1/16W 1% R60-63,R78-80,R83-85 VISHAY CRCW060349R9FNEA 0603 10 1/10W 5% R127-128 VISHAY CRCW060310R0JNEA 0603 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 99 ADSP-BF527 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 100PF 50V 5% C260-267 PANASONIC ECJ-1VC1H101J 0603 12.4K 1/10W DIGI-KEY 311-12.4KHRTR-ND 1% 0603 75.0 1/10W 1% R81-82 DALE CRCW060375R0FKEA 0603 100 1/16W 5% R44-45 DIGI-KEY 311-100JRTR-ND...
  • Page 100 0.027 1/2W 1% R101,R103 SUSUMU RL1632T-R027-F-N 1206 5.6K 1/16W R40-43 SUSUMU RR0510P-562-D 0.5% 0402 680 1/16W 1% BC COMPO- 2312 275 16801 0402 NENTS 90.9K 1/16W DIGI-KEY 541-90.9KLCT-ND 5% 0402 A-10 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 101 ADSP-BF527 EZ-KIT Lite Bill Of Materials Ref. Qty. Description Reference Designator Manufacturer Part Number 40.2K 1/16W DIGI-KEY 541-40.2KLCT-ND 5% 0402 3.3UF 16V 10% C113,C118,C120,C129 DIGI-KEY 490-3337-2-ND 0805 22UF 10V 10% C139,C142,C145 DIGI-KEY 490-1876-2-ND 1210 95K 1/10W 1% R136 DIGI-KEY 311-95.3KHRTR-ND...
  • Page 102 Ref. Qty. Description Reference Designator Manufacturer Part Number ON SEMI ESD5Z2.5T1G ESD5Z2.5T1 SOD-523 30A GSOT08 VISHAY GSOT08-GS08 SOT23-3 A-12 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 103 ADSP-BF527 EZ-KIT LITE SCHEMATIC ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF527 EZ-KIT Lite Title TITLE Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 104 Nashua, NH 03063 25MHZ Boot from UART1Host OSC003 DEVICES PH: 1-800-ANALOGD Reserved Boot from SDRAM 0.01UF ADSP-BF527 EZ-KIT Lite Title 0402 Reserved Boot from 8-bit NAND flash PORTF DSP EBIU + CONTROL Boot from 8-bit NAND flash PORTH Size Board No.
  • Page 105 AMS1_Z AMS0 AMS0_Z ARE_Z RNS003 ANALOG 20 Cotton Road ABE1#/SDQM1 ABE1#/SDQM1_Z Nashua, NH 03063 ABE0#/SDQM0 ABE0#/SDQM0_Z DEVICES PH: 1-800-ANALOGD SWE_Z ADSP-BF527 EZ-KIT Lite Title SCAS SCAS_Z SRAS SRAS_Z SERIES TERMINATION SMS_Z Size Board No. A0208-2006 RNS003 Date 1-13-2010_14:04 Sheet Arrow.com.
  • Page 106 DIO005 VDDINT33 AC12 AVDD_OTP Nashua, NH 03063 AB11 DEVICES VDDRTC OTP_VPP PH: 1-800-ANALOGD ADSP-BF527 MBGA289 C111 C146 C136 C135 ADSP-BF527 EZ-KIT Lite 0.01UF 0.1UF 0.1UF 0.1UF 0.1UF Title 0402 0402 0402 0402 0402 CON054 DSP POWER BATTHOLDER Size Board No.
  • Page 107 NDALE_HOSTD15 NDD3_ETXEN_HOSTD3 0.1UF 0.01UF NDCLE_HOSTD14 NDD4_RMIIREFCLK_HOSTD4 ANALOG 20 Cotton Road 0402 0402 NDD5_ETXD0_HOSTD5 Nashua, NH 03063 DEVICES NDBUSY#_HOSTD13 R/~B NDD6_ERXD0_HOSTD6 PH: 1-800-ANALOGD NDD7_ETXD1_HOSTD7 ADSP-BF527 EZ-KIT Lite Title NAND04 TSOP48 MEMORY Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 108 V5.5MLA PGB1010603 PGB1010603 PGB1010603 0603 0603 0603 0603 FER1 0.01UF 0603 0402 1206 ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF527 EZ-KIT Lite Title DSP USB OTG Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 109 DIP4 C269 PH: 1-800-ANALOGD SWT018 1000PF RSCLK0A 0805 DIP2 ADSP-BF527 EZ-KIT Lite SWT020 Title AUDIO CODEC MODE INTERFACE: AGND INTERNAL AUDIO CODEC SW20 and SWXX disconnect DSP from AUDIO CODEC SPI MODE: ON, OFF, ON, OFF TWI MODE: OFF, ON, OFF, ON Size Board No.
  • Page 110 C125 C124 C123 10UF 0.01UF 3.3UF 0.01UF 0.01UF 3.3UF 0.01UF 0.01UF 0.01UF 0.01UF 0805 0402 0805 0402 0402 0805 0402 0402 0402 0402 ADSP-BF527 EZ-KIT Lite Title RMII PHY SHGND2 Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 111 C303 0402 0402 ADP5520 R188 LFCSP_VQ24 0805 0805 C307 22PF 0805 ANALOG 20 Cotton Road Nashua, NH 03063 TP11 DEVICES PH: 1-800-ANALOGD ADSP-BF527 EZ-KIT Lite Title TOUCHSCREEN, KEYPAD AND BACKLIGHT Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 112 Nashua, NH 03063 GND5 IO68 PPIFS1 DEVICES PH: 1-800-ANALOGD GND6 IO69 PPIFS2 R305 GND7 IO70 C305 C249 C250 C248 0402 ADSP-BF527 EZ-KIT Lite 0.1UF 0.1UF 0.01UF 0.01UF Title GND8 0402 0402 0402 0402 LCD, CPLD XC95144XL TQ100 Size Board No. A0208-2006...
  • Page 113 SWT016 C161 0.1UF 0402 ANALOG 20 Cotton Road C156 0.01UF 0402 Nashua, NH 03063 "UART SETUP" DEVICES PH: 1-800-ANALOGD SERIAL PORT ADSP-BF527 EZ-KIT Lite Title ROTARY SWITCH, RS232 (UART 1) Size Board No. A0208-2006 Date 1-20-2010_14:13 Sheet Arrow.com. Downloaded from...
  • Page 114 20 Cotton Road Nashua, NH 03063 C167 DEVICES 0.01UF C306 C168 C166 PH: 1-800-ANALOGD 0402 0.01UF 0.01UF 0.01UF 0402 0402 0402 ADSP-BF527 EZ-KIT Lite Title LEDS, PUSHBUTTONS, RESET, HOST PORT Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 115 HOSTADDR_PUSHBUTTON2 CLKOUT R168 DEBUG_AGENT DSP JTAG HEADER 0603 CON019 CON019 CON019 SHGND ANALOG 20 Cotton Road Nashua, NH 03063 DEVICES PH: 1-800-ANALOGD ADSP-BF527 EZ-KIT Lite Title EXPANSION INTERFACE & JTAG Size Board No. A0208-2006 Date 1-13-2010_14:04 Sheet Arrow.com. Downloaded from...
  • Page 116 STAMP_RFS0A HOST_TFS0A_RMIIMDINT#_HOSTCE# TFS0A_RMIIMDINT#_HOSTCE# IDC5X2 DEVICES PH: 1-800-ANALOGD STAMP_RSCLK0A STAMP_TFS0A_RMIIMDINT#_HOSTCE# TFS0A_RMIIMDINT#_HOSTCE# IDC5X2 DIP2 SWT020 ADSP-BF527 EZ-KIT Lite Title SW21 disconnects TFS0A_RMIIMDINT#_HOSTCE# STAMP CONNECTORS from SPORT conn P6.11 and HOST conn P13.6 Size Board No. A0208-2006 Date 1-20-2010_14:13 Sheet Arrow.com. Downloaded from...
  • Page 117 100UF 22UF 47UF GSOT05 SO-8 1210 TP12 SOT23-3 ANALOG 20 Cotton Road R100 422K Nashua, NH 03063 0603 DEVICES PH: 1-800-ANALOGD PGND2 COPPER ADSP-BF527 EZ-KIT Lite Title PGND2 POWER PGND2 Size Board No. A0208-2006 Date 1-19-2010_15:47 Sheet Arrow.com. Downloaded from...
  • Page 118 CCLK register, 1-16 1-24, 2-22 clock in (CLK IN) signal, CPLD D8-13 switch (SW29), 2-22 audio codec, See audio interface CTS signal, 1-26 code security, 1-11 configuration, of this EZ-KIT Lite, ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 119 JP5 (UART1 loopback), 2-24 flash WP jumper (JP10), 2-24 JP6 (mic select), 1-24, 2-23 JP7 (STAMP enable), 2-23 P14 (VDDINT power), 1-29, 2-25 P15 (VDDEXT power), 1-29, 2-25 P16 (VDDMEM power), 1-29, 2-25 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 120 PG0-10 signals, LINOUT signal, 1-24 PG11-12 (IO) signals, 1-19, 1-20, 2-5, 2-26 Lockbox secure technology, 1-11 PG13 (IO) signal, 1-25, loopback switch (SW28), 2-22 PG14-15 (IO) signals, PG8 (IO) signal, 2-26 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 121 2-19 RS-232 connector (J4), 2-29 SW22 (touch address) switch, 1-21, 2-19 RTC power pin, 1-27 SW24 (touchpad interrupt) switch, 1-21, 2-20 RTS signal, 1-26 SW25 (LCD/keypad control) switch, 1-18, 1-21, 2-20 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...
  • Page 122 VR3 (USB voltage) regulator, 1-25 touchpad interrupt switch (SW24), 1-21, 2-20 touchscreen address switch (SW22), 1-21, 2-19 two-wire interface (TWI) config switch (SW19), 1-24 watchdog timer, 1-27 connector (P10), 2-33 selecting for codec, 1-24 ADSP-BF527 EZ-KIT Lite Evaluation System Manual Arrow.com. Downloaded from...

Table of Contents