Fibocom FM350R-GL Hardware Manual
  1. Manuals
  2. Brands
  3. Fibocom Manuals
  4. Computer Hardware
  5. FM350R-GL
  6. Hardware manual
Fibocom FM350R-GL Hardware Manual

Fibocom FM350R-GL Hardware Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FM350R-GL
Hardware Guide
V1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FM350R-GL and is the answer not in the manual?

Questions and answers

Related Manuals for Fibocom FM350R-GL

Summary of Contents for Fibocom FM350R-GL

  • Page 1 FM350R-GL Hardware Guide V1.0...
  • Page 2 All the statements, information and suggestions contained in the document do not constitute any explicit or implicit guarantee. Trademark The trademark is registered and owned by Fibocom Wireless Inc. Contact Website: https://www.fibocom.com/en/ Address: Floor 10, Building A, Shenzhen International Innovation Valley, First Stone Road,...

  • Page 3: Specification

    1 Foreword 1.1 Introduction FM350R-GL (hereinafter referred to as FM350R) is a highly integrated 5G Sub-6 WWAN module which uses M.2 form factor interface. It supports GNSS and NR/LTE/WCDMA systems which can be applied to most cellular networks of mobile carrier in the world.

  • Page 4: Key Features

    Modulation Characteristic 3GPP Release 15 200MHz 2 DLCA, 256 QAM NR Sub6 Modulation 200MHz 2 ULCA, 256 QAM 15KHz/30KHz SCS for FDD/TDD 3GPP Release 15 100MHz 5 DLCA, 256 QAM Modulation 40MHz 2 ULCA, 256 QAM UMTS 3GPP Release 8 Modulation RF Characteristic HPUE...
  • Page 5 MTK T700, 7nm process, ARM Cortex-A55, up to 1.5 GHz Memory 4Gb LPDDR4X+4Gb NAND Flash Supported OS Windows 11/Chrome/Linux Power Supply DC 3.135V to 4.4V, typical 3.3V Normal operating temperature: –10°C to +55°C Temperature Extended operating temperature: –30°C to +75°C Storage temperature: –40°C to +85°C Humidity Operating relative humidity: <=95%...
  • Page 6 3) When temperature goes beyond normal operating temperature range of -10°C to +55°C, RF performance of module may be slightly off 3GPP specifications.

  • Page 7: Federal Communication Commission Interference Statement

    2 FCC Conformance information Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  • Page 8 This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.

  • Page 9: End Product Labeling

    Fibocom Wireless Inc. that they wish to change the antenna trace design. In this case, a Class II permissive...

  • Page 10: Antenna Information

    Antenna information Band Gain(dBi) Type Band Gain(dBi) Type WCDMA Band 2 LTE Band 48 WCDMA Band 4 LTE Band 66 WCDMA Band 5 LTE Band 71 LTE Band 2 5G NR Band 2 LTE Band 4 5G NR Band 5 LTE Band 5 5G NR Band 7 LTE Band 7...

  • Page 11: Industry Canada Statement

    3 IC Conformance information Industry Canada Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
  • Page 12 This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.

  • Page 13: Plaque Signalétique Du Produit Final

    d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
  • Page 14 4 CE Conformance information The device could be used with a separation distance of 20cm to the human body. Hereby, [Fibocom Wireless Inc.] declares that the radio equipment type [FM350R-GL] is in compliance with Directive 2014/53/EU. 4.1 Transmitting Power of EU bands...
  • Page 15 Band 3GPP Requirement (dBm) Tx Power (dBm) 23±2.7 23±1 23±2.7 23±1 23+2.7/-3.2 23±1 23±2.7 23±1 23±2.7 23±1 26+3/-4 26±1 (HPUE) 23+3/-3 23±1 26+3/-4 26±1 (HPUE) 23+3/-4 23±1 26+3/-4 26±1 (HPUE) 23+3/-4 23±1 The max TX power is in primary RF path at ambient temperature 25°C.
  • Page 16 5 NCC Conformance information NCC Statement 減少電磁波影響，請妥適使用 Support WCDMA B1,B8/LTE B1,B3,B7,B8,B28,B38,B41/5G NR n1,n3.n7.n8.n28.n38,n41,n78,n79 電波功率密度 MPE 標準值: mW/cm2，送測產品實測值: mW/cm2，建議 使用時設備天線至少距離人體 20 公分。...

Table of Contents