Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Digitus DS-55353
Summary of Contents for Digitus DS-55353
- Page 1 HDMI IP POE Extender Set, 4K/60Hz Installation Guide DS-55353, DS-55354...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ------------------------------------------------------- 3 2. Main Features ----------------------------------------------------- 4 3. Package Content (DS-55353) ---------------------------------- 4 4. Specification ------------------------------------------------------- 5 5. Interfaces----------------------------------------------------------- 7 5.1 Transmitter (TX) ---------------------------------------------- 7 5.2 Receiver (RX) -------------------------------------------------- 9 6. Installation Requirements ----------------------------------- 10 7. -
Page 3: Introduction
1. Introduction The HDMI IP Extender Set, 4K/60Hz enables the transmission of HDMI AV signals in ultra-high-definition 4K quality (4096x2160p at 60Hz) over long distances of up to 200 meters - thanks to the powerful point-to-point connection via a CAT6 network cable or higher. The set is fully powered via a POE network switch, external power supply units are not required. -
Page 4: Main Features
IR interface enables remote control of the input source • from the output screen • Supports CAT6 (or higher) network cables Suitable for wall mounting • 3. Package Content (DS-55353) 1x Transmitter unit • 1x Receiver unit • 2x IR cable/extension (1.0 m) •... -
Page 5: Specification
4. Specification Item Transmitter Receiver Video Input interface 1x HDMI 1x RJ45 Output interface 1x RJ45 1x HDMI HDMI length 5 m max. 5 m max. Maximum 18 Gbps transfer rate HDMI 2.0 Compatibility HDCP 1.4/ HDCP 2.2 4096x2160@24/30/50/60Hz, 3840x2160@24/30/50/60Hz, 1080P@24/25/30/50/60Hz, 720P@50/60Hz, 576P@60Hz, Resolutions... - Page 6 Transmission 1080P: 80-130 ms latency 4K/60Hz: 150-220 ms Audio Signal Input interface 1x HDMI 1x RJ45 Output interface 1x RJ45 1x HDMI HDMI output LPCM 2.0 3. 5mm L/R output Command Signal 1x 3.5mm IR interface 1x 3.5mm IR In IR Out IR receiving range 5 m max.
-
Page 7: Interfaces
Housing Metal Weight TX: 166 g RX: 164 g Color Black Dimensions 96.8 (L) x 94 (W) x 23.7 (H) mm ESD protection 1a Contact discharge level 2 (±4KV) 1b Air discharge level 3 (±8KV) Implementation of the standard: Protection IEC61000-4-2 Lightning protection, Surge protection... - Page 8 Power light The indicator will turn Reset on when the power is turned on Firmware RJ45 signal output upgrading Data transmission light light off: No data HDMI signal transmission input Steady on: the data is transmitting Network link light IR signal output ...
-
Page 9: Receiver (Rx)
5.2 Receiver (RX) Power light The indicator will turn Reset on when the power is turned on Firmware RJ45 signal input upgrading Data transmission light light off: No data HDMI signal transmission output Steady on: the data is transmitting... -
Page 10: Installation Requirements
Network link light IR signal input to light off: No Network connect with IR connection receiver Steady on: Network extension cable connection is normal Power input (DC 5V/1A) 6. Installation Requirements HDMI source device (PC, NVR, Streaming Device, etc.) •... -
Page 11: Connection Diagrams
7.2 Connection Diagrams Distance: 120 m max. for one-to-many connection, 200 m max. for one-to-one connection 7.2.1 One-to-One Connection 7.2.2 Cascading (by network switch): By using the LAN switch/router to realize unlimited extension. -
Page 12: Ir User Guide
7.2.3 One-to-Many Connection: By using network switch, one sender to several receivers to realize extender & splitter function Note: Please use POE network router/switch. It is recommended to use Gigabit Ethernet switches (1000Mbps) in the LAN 7.3 IR User Guide 1. -
Page 13: Faq
Q: Display shows: ” Waiting for connection…” 1) Please check if the TX (sender) and network switch (if used) and RX (receiver) are connected, and make sure all cable connections are firmly. 2) Try “Reset” via button Q: Display shows “Please check the TX input signal” 1) Please check if there is a HDMI signal input on TX 2) Try to connect the signal source directly to the display device to see if there is signal output from source device... - Page 14 Hereby ASSMANN Electronic GmbH declares that the Declaration of Conformity is part of the shipping content. If the Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address. info@assmann.com Assmann Electronic GmbH Auf dem Schüffel 3 58513 Lüdenscheid Germany...
Need help?
Do you have a question about the DS-55353 and is the answer not in the manual?
Questions and answers