1. Manuals
  2. Brands
  3. Power Team Manuals
  4. Water Pump
  5. PA9 Series
  6. Operating instructions manual

Power Team PA9 Series Operating Instructions Manual

Air hydraulic pump
Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Table of Contents

Hydraulic Technologies
5885 11th Street
Rockford, IL 61109-3699 USA
Internet Address:
http://www.powerteam.com
Workstation Sound Pressure Level: 80 dB(A) at Rated Capacity
Definition: An air hydraulic pump delivers hydraulic fluid under pressure through the use of compressed air
as a power source.
Two safety symbols are used to identify any action or lack of action that can cause personal injury. Your
reading and understanding of these safety symbols is very important.
DANGER - Danger is used only when your action or lack of action will cause serious human injury or
death.
WARNING - Warning is used to describe any action or lack of action where a serious injury can occur.
IMPORTANT - Important is used when action or lack of action can cause equipment failure, either immediate
or over a long period of time.
WARNING: It is the operator's responsibility to read and understand the following
safety statements,
•
Only qualified operators should install, operate, adjust, maintain, clean, repair, or
transport this machinery.
•
These components are designed for general use in normal environments. These
components are not specifically designed for lifting and moving people, agri-food
machinery, certain types of mobile machinery or special work environments such as:
explosive, flammable or corrosive. Only the user can decide the suitability of this
machinery in these conditions or extreme environments. Power Team will supply
information necessary to help make these decisions.
These instructions are intended for end-user application needs. Most problems with new equipment are caused by
improper operation or installation. Detailed service repair instructions or parts lists can be obtained from your nearest
Power Team facility (see listing).
© Hydraulic Technologies
Tech. Services: (800) 477-8326
Fax: (800) 765-8326
Order Entry: (800) 541-1418
Fax: (800) 288-7031
AIR HYDRAULIC PUMP
Max. Pressure: See Pump Data Plate
SAFETY EXPLANATIONS
Operating Instructions for:
Sheet No.
Rev 3
Form No. 102904
63-0005
PA9 Series
1 of 4
Date: 17 Nov 2005

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PA9 Series and is the answer not in the manual?

Questions and answers

Related Manuals for Power Team PA9 Series

Summary of Contents for Power Team PA9 Series

  • Page 1 Only the user can decide the suitability of this machinery in these conditions or extreme environments. Power Team will supply information necessary to help make these decisions.

  • Page 2: Safety Precautions

    • Replace worn or damaged safety decals. • Modification of a product requires written Power Team authorization. • Use only components with the same pressure rating when assembling a system or machine. Pump •...

  • Page 3: Hydraulic Connections

    Operating Instructions Form No. 102904 Hydraulic Connections Clean all the areas around the fluid ports of the pump and cylinder. Inspect all threads and fittings for signs of wear or damage and replace as needed. Clean all hose ends, couplers and union ends. Remove the thread protectors from the hydraulic fluid outlets.

  • Page 4: Pictogram Definitions

    Operating Instructions, Form No. 102904, Back sheet 2 of 4 OPERATION PICTOGRAM DEFINITIONS Activating the pump with the pedal end marked with this pictogram, the flow of fluid is directed out of the reservoir. Activating the pump with the pedal end marked with this pictogram, the flow of fluid is directed back to the reservoir.

  • Page 5: Preventive Maintenance

    Inspecting The Hydraulic Oil Level Check the oil level in the bladder after every 10 hours of use. Drain and replenish the bladder with Power Team hydraulic oil after every 300 hours of use approximately.
  • Page 6 Refilling The Bladder If additional oil must be added to the bladder, use only Power Team hydraulic oil (215 SSU @ 100° F [38° C]). Clean the entire area around the filler plug before adding oil to the bladder. Remove the filler plug, and insert a clean funnel with filter.
  • Page 7 Operating Instructions Form No. 102904 OPERATOR TROUBLESHOOTING GUIDE If this guide does not resolve your pump problem, contact an authorized hydraulic service center or a company headquarters listed on back sheet 4 of 4. PROBLEM CAUSE SOLUTION Pump reciprocates but no oil 1.

  • Page 8: Power Team Facilities

    Operating Instructions, Form No. 102904, Back sheet 4 of 4 POWER TEAM FACILITIES UNITED STATES CHINA EUROPE Albert Thijsstraat 12 C E R T I F I E D 212 Jiang Ning Road Hydraulic Technologies 6471 WX Eygelshoven CATIC Tower 23C...
  • Page 9 Telephone: 815-874-5556 MANUFACTURER’S ADDRESS: Rockford, Illinois 61109 Fax: 815-874-7853 RECIPROCATING AIR PISTON HYDRAULIC PUMP. TYPE OF EQUIPMENT: PA9 Series ORDER NUMBER OR PART NUMBER: 89/392/EEC as amended by 91/368/EEC, 93/44/EEC, and APPLICATION OF EC COUNCIL DIRECTIVE(S): 93/68/EEC. EN292-1, and EN292-2.

This manual is also suitable for:

63-0005Pa9h6-141963-0012

Table of Contents