Advertisement
OPTICAL FIBER PHOTOELECTRIC
SENSOR
E3X-SD
（SD21/SD51/SD7/SD9）
Thank you for selecting OMRON product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product.
·Please let the experts operate with electric knowledge.
·Please use the product correctly on the basic of reading
and understanding the instruction sheet.
·Please keep this instruction sheet well for using.
●Meanings of Signal Words
CAUTION
●Alert statements in this Manual
Do not use it exceeding the rated voltage.
There is a possibility of failure and fire.
Do not connect sensor to AC power supply.
Risk of explosion.
Hot surface may cause heat injury.
1)Do not use the Amplifier Unit in environments subject to flamm-
able or explosive gases.
2)Do not use the Amplifier Unit in environments subject to exposu-
re to water, oil, chemicals, etc.
3)Do not attempt to disassemble, repair, or modify the Amplifier U-
nit in any way.
4)Do not apply voltages or currents that exceed the rated ranges.
5)Do not use the Amplifier Unit in atmospheres or environments th-
at exceed product ratings.
6)Wire the Amplifier Unit correctly, e.g., do not reverse the polarity
of the power supply.
7)Connect the load correctly.
8)Do not short both ends of the load.
9)Do not use the Amplifier Unit if the case is damaged.
10)When disposing of the Amplifier Unit, treat it as industrial waste.
11)Do not use the sensor in the place exposed to the direct sunlight.
12)The surface temperature of sensor rises depending on the use c-
onditions such as ambient temperature and power supply volt-
age. Be careful when you operate or clean it. Hot surface may
cause heat injury.
Instruction Sheet
Precaution on Safety
Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury or in property damage.
Precautions for Safe Use
* 2 1 1 7 6 7 5 - 8 B *
CAUTION
Advertisement
Table of Contents
Related Manuals for Omron E3X-SD
Summary of Contents for Omron E3X-SD
- Page 1 SENSOR E3X-SD （SD21/SD51/SD7/SD9） Instruction Sheet Thank you for selecting OMRON product. Before operating the product, read the sheet thoroughly to acquire sufficient knowledge of the product. ·Please let the experts operate with electric knowledge. ·Please use the product correctly on the basic of reading and understanding the instruction sheet.
-
Page 2: Precautions For Correct Use
Precautions for Correct Use 1)Do not use the Amplifier Unit under the following conditions. ①In the place exposed to the direct sunlight. ② In the place where humidity is high and condensation may occur. ③In the place where corrosive gas exists. ④In the place where vibration or shock is directly transmitted to the product. -
Page 3: Installing The Amplifier Unit
5.Installing the Amplifier Unit ■ Mounting Units Catch the hook on the Fiber Unit connector end of the Unit on the DIN Track and then press down on the other end of the Unit until it locks into place. Always TEACHach the Fiber Unit connector end first. DIN Track If the incorrect end is TEACHached first, the Hook on the Fiber Unit connector end... -
Page 4: Convenient Function
8.2 With/without Workpiece Teaching Quick Tuning Get two point about with/without workpiece, then set the action level in the middle. Display Display Operation Description Description TEACH If there is TEACH workpiece, Display TEACH TEACH press Teach threshold key and hold value of first flash once it within 3... -
Page 5: Suitability For Use
COMPONENT OR PROTECTIVE DEVICE FOR SUCH PURPOSES. Please refer to separate catalogs for OMRON's safety rated products. OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the products in the customer's application or use of the product.
Need help?
Do you have a question about the E3X-SD and is the answer not in the manual?
Questions and answers