(servicing) instructions in the components or accessories elsewhere defined to be used with the installation of the product, they must literature accompanying the product. be used in order to ensure compliance with FCC regulations. www. zeevee.com Page 2 HDbridge3000 Configuration Guide...
100 - 240 V AC / 50 - 60 Hz, hot-swappable, dual-redundant power supplies. Both AC power cords (included) must be connected to the HDbridge3000 for proper operation. * Not all cards support IP out. Page 4 HDbridge3000 Configuration Guide www.zeevee.com...
Page 5
Display Displays configuration and system status. This display can also be found on the opposite panel. Cooling Fans Hot-swappable, high-capacity cooling fans. Air is pulled in from these fans and expelled through the front panel. When installing the HDbridge3000, make sure that these fans are not blocked and clear from other heat- generating sources.
5. Connect the included AC power cords from both power update to the latest version of firmware, which can be found supplies to available AC outlets. on the Support section of the ZeeVee website. Tuning your channel at the HDTV (Auto Scan) Beginning Setup Select the Cable setting (not Air or Antenna) in your Install the desired module in each slot.
The HDbridge3000 has a small display, located on both the front and back panel of the unit. When the display is in "standby", the ZeeVee logo is displayed. Press the NAV wheel to display the IP address / port status of the HDbridge3000.
Click Apply to save changes. Your unit stores configurations so they are not lost on power-down. Run Auto Scan at TV (see Tuning your channel at the HDTV, page 5) when you have saved configuration changes. Page 8 HDbridge3000 Configuration Guide www.zeevee.com...
Map for configuring RF Cable TV Channels vs RF Frequency (MHz) Map channels and virtual channels RF Ch. Band (MHz) RF Ch. Band (MHz) RF Ch. Band (MHz) RF Ch. Band (MHz) RF Ch. Band (MHz) The table, to the right, shows how logical RF channels are matched 54-60 240-246...
Configuration dialog will be displayed. 11. Click the Close button to dismiss the dialog. NOTE: All saved settings are retained, even if the HDbridge3000 is powered-off. Card settings are automatically migrated when swapping cards of the same type. Page 10 HDbridge3000 Configuration Guide www.zeevee.com...
Using other Maestro tabs Click on any other Maestro tab to configure your unit as needed. We provide brief information below. Please click on the Help button on each tab or refer to the Support section of our website for further detail on configuration options. AV Source tab Allows for specifying audio and video inputs and adjusting...
Page 12
This channel is disabled by default, but can be enabled at any time under the RF Channel Plan tab. Visit zeevee.com/ zvshow for details. STB tab Provides management of DirecTV H25 receivers. For...
Page 13
Admin tab Use this Admin tab to create user accounts and grant access to specific functions within the Maestro web interface. Maestro allows for a total of 10 custom user accounts, not including the "admin" account. Support tab Provides technical support contact information and allows you to send logs for troubleshooting.
Use the Dly Aud port on the card, if available, and adjust the delay amount using Maestro. Feed the audio to the ZeeVee unit and send it to the HDTV with the video. Then take the audio out from an HDTV or external QAM tuner (such as the ZvSync) and connect it to your audio system.
ZeeVee Equipment. comparable product (whichever ZeeVee deems ZeeVee Equipment as a gift from the original end user as necessary). purchaser and to no other purchaser or transferee. All TO GET WARRANTY SERVICE •...
Contact ZeeVee Support For additional questions call +1(877) 4-ZEEVEE (1.877.493.3833) or e-mail support@zeevee.com. Representatives are available from 9:00 AM to 6:00 PM, Monday through Friday (Eastern Time). Sales North America: +1 (347) 851-7364 Phone sales@zeevee.com EMEA: +44 1494 956677 Phone EMEAsales@zeevee.com...
Need help?
Do you have a question about the HDB3KR-NA and is the answer not in the manual?
Questions and answers