Page 1 Cisco 11500 Series Content Services Switch Hardware Installation Guide Software Version 7.20 July 2003 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Customer Order Number: DOC-7813884=...
Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...
Page 3 CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST,...
Page 5: Table Of Contents
Safety Guidelines Chassis-Lifting Guidelines for the CSS 11503 and CSS 11506 Electrical Safety Specifications for Cisco 11500 Series Power Supplies Power Guidelines for DC Systems (CSS 11503 and CSS 11506) Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 6 Installation Precautions and Restrictions 1-20 Installation Precautions 1-20 Module Slot Restrictions 1-21 Unpacking a CSS Module 1-24 Installing a Module 1-24 Installing a Passive SCM in a CSS 11506 1-26 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 7 Powering Up the CSS 2-36 Powering Down the CSS 2-36 Troubleshooting the CSS Hardware Components 2-37 Troubleshooting the CSS 11501 2-37 Troubleshooting the CSS Modules 2-39 Troubleshooting the Console Interface 2-42 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 8 Environmental Specifications Physical Specifications CSS 11501 Bandwidth and Memory Specifications CSS 11503 and CSS 11506 Module Specifications Disk Specifications Supported Standards Transport Network Routing Gateway Application Network Utilities Network Management Cisco 11500 Series Content Services Switch Hardware Installation Guide viii 78-13884-06...
Page 9 A P P E N D I X Configuring a Modem Cabling a Modem to the CSS Regulatory Compliance and Safety Information for the Cisco 11500 Series A P P E N D I X Content Services Switch Agency Approvals...
Page 10 Installation and Replacement Warning D-43 Use Copper Conductors Only Warning D-44 Short-circuit Protection Warning D-45 Faceplates and Cover Panels Warning D-47 Power Module Warning D-50 Ground Conductor Warning D-52 N D E X Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 11 Connecting a CSS 11503 AC Power Cord 2-27 Figure 2-13 Location of the CSS 11503 DC Power Supply Connectors 2-29 Figure 2-14 Connecting a CSS 11506 AC Power Cord 2-31 Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 12 Location of the CSS 11506 Power Supplies 2-45 Figure 2-17 CSS 11506 AC Power Supply LEDs 2-46 Figure 2-18 CSS 11506 DC Power Supply LEDs 2-46 Figure C-1 Switch Control Module Console Connector Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 13 LEDs of the CSS 11506 Power Supply 2-47 Table A-1 AC Electrical Specifications Table A-2 DC Electrical Specifications Table A-3 Environmental Specifications Table A-4 Physical Specifications Table A-5 CSS 11501 Specifications Cisco 11500 Series Content Services Switch Hardware Installation Guide xiii 78-13884-06...
Page 14 Console Port to Terminal Signals and Pinouts Table B-5 Console Port to Modem Signals and Pinouts Table B-6 RJ-45 Management Connector Pinouts Table C-1 CSS Console Port Default Settings Table D-1 Regulatory Approval Requirements Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 15: About This Guide
About This Guide This guide is intended to help you install your Cisco 11500 Series Content Services Switches (CSS), models CSS 11501, CSS 11503, and CSS 11506. It provides you with instructions for installing, cabling, and powering the CSS. Information in this guide applies to all CSSs except where noted.
Page 16: Audience
CSS, and troubleshooting the CSS console, modules, and power supply. Appendix A, Provides specifications for the CSS and its components. Specifications Appendix B, Provides pinouts for each connector on the CSS. Cable Connector Pinouts Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 17: Related Documentation
OSPF • Logging, including displaying log messages • and interpreting sys.log messages User profile and CSS parameters • • SNMP and RMON Offline Diagnostic Monitor (Offline DM) • menu Cisco 11500 Series Content Services Switch Hardware Installation Guide xvii 78-13884-06...
Page 18 Box-to-box redundancy Demand-based content replication and content • staging and replication Secure Socket Layer (SSL) termination with • the SSL Acceleration Module Firewall load balancing • CSS scripting language • Cisco 11500 Series Content Services Switch Hardware Installation Guide xviii 78-13884-06...
Page 19: Symbols And Conventions
Italics text indicates the first occurrence of a new term, book title, and emphasized text. A numbered list indicates that the order of the list items is important. An alphabetical list indicates that the order of the secondary list items is important. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 20: Obtaining Documentation
These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm You can access the Cisco website at this URL: http://www.cisco.com...
Page 21: Ordering Documentation
About This Guide Obtaining Documentation Registered Cisco.com users can order a single Documentation CD-ROM (product number DOC-CONDOCCD=) through the Cisco Ordering tool: http://www.cisco.com/en/US/partner/ordering/ordering_place_order_ordering_t ool_launch.html All users can order monthly or quarterly subscriptions through the online Subscription Store: http://www.cisco.com/go/subscription Ordering Documentation You can find instructions for ordering documentation at this URL: http://www.cisco.com/univercd/cc/td/doc/es_inpck/pdi.htm...
Page 22: Obtaining Technical Assistance
Cisco.com offers a suite of interactive, networked services that let you access Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world. Cisco.com provides a broad range of features and services to help you with these tasks: Streamline business processes and improve productivity •...
Page 23: Cisco Tac Website
If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC website, you can open a case online at this URL: http://www.cisco.com/tac/caseopen If you have Internet access, we recommend that you open P3 and P4 cases online so that you can fully describe the situation and attach any necessary files.
Page 24: Cisco Tac Escalation Center
These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case. To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL: http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml...
Page 25 You can access Packet magazine at this URL: http://www.cisco.com/go/packet • iQ Magazine is the Cisco bimonthly publication that delivers the latest information about Internet business strategies for executives. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine Internet Protocol Journal is a quarterly journal published by Cisco Systems •...
Page 26 About This Guide Obtaining Additional Publications and Information Cisco 11500 Series Content Services Switch Hardware Installation Guide xxvi 78-13884-06...
Page 27: Chapter 1 Unpacking And Installing The Css
• • If the Product is Damaged Preinstallation Requirements • • Installing the CSS 11501 • Installing the CSS 11503 Installing the CSS 11506 • • Installing a CSS Module Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 28: Site Requirements
When you install the CSS, observe all of the caution and warning statements in the installation procedures. For warning translations, refer to Appendix D, Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch. Read the following guidelines to help ensure your safety and protect the equipment.
Page 29: Chassis-Lifting Guidelines For The Css 11503 And Css 11506
If you remove the fan assembly and power modules to lighten the chassis, be • sure to provide anti-static mats or bags to protect the removed components. Be careful when you remove the power modules—they are heavy. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 30: Electrical Safety
Unpacking and Installing the CSS Safety Guidelines • Cisco Systems recommends that you leave line cards installed in the chassis. Removing line cards greatly increases the chances of damage to the chassis or components, and introduces the possibility that you will unintentionally change the configuration.
Page 31 Warning Read the installation instructions before you connect the system to its power source. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 32: Specifications For Cisco 11500 Series Power Supplies
CSS 11506 Voltage DC -48.0 to -60.0 VDC -48.0 to -60.0 VDC Current DC (maximum) 9 Amps 18 Amps Power Consumption 430VA 860VA (maximum) Heat Dissipation 1468 BTU/hr 2936 BTU/hr Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 33: Power Guidelines For Dc Systems (Css 11503 And Css 11506)
Once you complete the installation, you need a console terminal (or equivalent) that runs at 9600 baud to enter console commands (refer to Chapter 2, Cabling and Troubleshooting the CSS). Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 34: Shipment Contents
Note If you cannot locate the Standard software license key or a license key Claim Certificate in the accessory kit, call the Cisco Technical Assistance Center (TAC) toll free, 24 hours a day, 7 days a week at 1-800-553-2447 or 1-408-526-7209. You can also e-mail TAC at tac@cisco.com.
Page 35: Unpacking The Css
CSS later. Check the configuration of the CSS and the accessories against the items listed on the packing slip. Report any discrepancies as described in “If the Product is Damaged” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 36: If The Product Is Damaged
Upon receipt of this information, you will be provided with service instructions, or a Return Material Authorization (RMA) number and shipping information. To obtain assistance, refer to “About This Guide”, the “Obtaining Documentation” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-10 78-13884-06...
Page 37: Preinstallation Requirements
The minimum clearance requirement is 2 inches (10 cm) of air flow space on • both sides of the chassis. Ensure that the CSS is reliably grounded to earth. Cisco Systems recommends • that you do not use power strips or extension cords to connect the CSS to the power source.
Page 38: Installing The Css 11501
Attach the rubber feet, provided in the accessory kit, to each bottom corner of the CSS. All cables connect to the front of the chassis with the exception of the power cord. Note Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-12 78-13884-06...
Page 39: Installing A Css 11501 As A Rackmounted Unit
Raise the CSS to the installation height and align the screw holes on the mounting bracket with the holes on the equipment rack. Secure each mounting bracket to each side of the rack. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-13 78-13884-06...
Page 40: Installing The Css 11503
Attach the rubber feet, provided in the accessory kit, to each bottom corner of the CSS. All cables connect to the front of the unit with the exception of the power cord. Note Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-14 78-13884-06...
Page 41: Installing A Css 11503 As A Rackmounted Unit
LINK S W I T C PCM CIA SLO T 1 SLO T 0 CON SOL E LINK DPL X LINK DPL X LINK DPL X LINK DPL X Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-15 78-13884-06...
Page 42: Figure 1-3 Mid-Mounting The Mounting Brackets On The Css 11503
Raise the CSS to the installation height and align the screw holes on the mounting bracket with the holes on the equipment rack. Secure each mounting bracket to each side of the rack. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-16 78-13884-06...
Page 43: Installing The Css 11506
10 0-2 40 V 5A 50 -60 10 0-2 40 V 5A 50 -60 This section covers: Mid-Mounting the CSS 11506 Mounting Brackets • • Rack-Mounting the CSS 11506 Chassis Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-17 78-13884-06...
Page 44: Mid-Mounting The Css 11506 Mounting Brackets
Repeat steps 1 through 3 to reposition the other mounting bracket on the other side of the chassis. To install the chassis in a rack, proceed to the “Rack-Mounting the CSS 11506 Chassis” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-18 78-13884-06...
Page 45: Rack-Mounting The Css 11506 Chassis
This information applies to the CSS modules only. If you received an additional module at a later time, it comes with a reference sheet providing information on the module and how to install it. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-19 78-13884-06...
Page 46: Installation Precautions And Restrictions
Installing a CSS Module Installation Precautions and Restrictions This section includes background material related to installing a module into the CSS chassis. Cisco Systems recommends that you read the topics in this section before installing a module. Installation Precautions Read and observe the following precautionary information prior to servicing the CSS.
Page 47: Module Slot Restrictions
CSS 11506 Chassis Slot Restriction Slot Number Slot Usage Initial active Switch Control Module (SCM) Initial passive SCM or I/O module I/O module I/O module I/O module I/O module Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-21 78-13884-06...
Page 48: Figure 1-6 Fully-Configured Css 11503
SLO T 1 SLO T 0 CON SOL E LINK DPL X LINK DPL X LINK DPL X LINK DPL X Slot location 1 Slot location 3 Slot location 2 Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-22 78-13884-06...
Page 49: Figure 1-7 Fully-Configured Css 11506
10 0-2 40 V 5A 50 -60 10 0-2 40 V 5A 50 -60 Slot location 1 Slot location 4 Slot location 2 Slot location 5 Slot location 3 Slot location 6 Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-23 78-13884-06...
Page 50: Unpacking A Css Module
To install a module into the CSS chassis, see the “Installing a Module” section. Installing a Module You must power down the CSS before installing or removing a Switch Module in Caution a CSS 11506. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-24 78-13884-06...
Page 51: Figure 1-8 Installing A Module Into A Css Chassis
Close both ejectors simultaneously to seat the module connector into the backplane. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. Reboot the chassis to activate the module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-25 78-13884-06...
Page 52: Installing A Passive Scm In A Css 11506
Extend both ejectors simultaneously to seat the module connector into the backplane. Using a Phillips screwdriver, tighten the spring-loaded screws on the front of the module faceplate. Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-26 78-13884-06...
Page 53: Figure 1-9 Installing A Pcmcia Cover On An Scm
To copy the boot configuration from the active SCM to the passive SCM, use the passive sync command in boot configuration mode. For more information, refer to the Cisco Content Services Switch Administration Guide. Cisco 11500 Series Content Services Switch Hardware Installation Guide...
Page 54 Chapter 1 Unpacking and Installing the CSS Installing a CSS Module Cisco 11500 Series Content Services Switch Hardware Installation Guide 1-28 78-13884-06...
Page 55: Chapter 2 Cabling And Troubleshooting The Css
Connecting the Console • • Connecting the Chassis to Ground Connecting the Power Cord • Powering Up the CSS • • Powering Down the CSS Troubleshooting the CSS Hardware Components • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 56: Cabling The Css 11501
RJ-45 10-Mbps half-duplex Ethernet management connector • RJ-45 RS-232 Diag connector (reserved for field service diagnostic use only). • • Eight auto-sensing 10/100-Mbps Ethernet (10BASE-T/100BASE-TX) interfaces Optional integrated Secure Sockets Layer (SSL) termination • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 57 Two status module LEDs indicating power and device readiness Link/Act and Duplex LEDs for the Ethernet Management port • Link/Act and Duplex LEDs for each Ethernet port • • Link/Act LED for the SFP GBIC Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 58: Css 11501 Connectors And Leds
1. The Ethernet Link/Act LED and Duplex LED are located at the top of each RJ-45 Ethernet connector and are not visible in this illustration. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 59: Table 2-1 Css 11501 Led Descriptions
Ethernet Port is operating at full duplex. Management Port Link/Act Green No link established. for Ethernet Port Link established but no activity. Blinking Link established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 60: Cabling The Css 11503 And Css 11506 Modules
For information on the connector pinouts, refer to Appendix B, Cable Connector Pinouts. If you encounter problems with the modules in the CSS 11503 and CSS 11506, see the “Troubleshooting the CSS Modules” section later in this chapter. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 61: Css 11503 And Css 11506 Module Overview
• The Cisco 11506 is a five-rack unit, supporting six-slots, with 40-Gbps aggregate throughput. The CSS 11506 requires at least one Switch Control Module (SCM) and may be configured with a second SCM in standby mode for redundancy.
Page 62 The CSS 11503 supports a maximum of two SSL modules and the CSS 11506 supports a maximum of four SSL modules. For information on SSL commands and functions, refer to the Cisco Content Services Switch Advanced Configuration Guide.
Page 63: Figure 2-2 Css 11503 Content Services Switch
SLOT 0 CON SOLE LINK DPLX LINK DPLX LINK DPLX LINK DPLX Slot 1 for the SCM only Slot 3 for an I/O module Slot 2 for an I/O module Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 64: Figure 2-3 Css 11506 Content Services Switch
Slot 6 Switch Modules in slots 7 and 8 Power supplies 1, 2, and 3 1. Slots 3 through 6 are for I/O modules, including SAMs and SSL modules. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-10 78-13884-06...
Page 65: Switch Control Module Connectors And Leds
Because invisible radiation may be emitted from the aperture of the port when Warning no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-11 78-13884-06...
Page 66: Figure 2-4 Switch Control Module Connectors And Leds
LC-type SFP GBIC (one of two) 12 Recessed button (reserved for field service use only) Link LED for the associated SFP GBIC on the left Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-12 78-13884-06...
Page 67: Table 2-2 Switch Control Module Led Descriptions
Link Green There is no link. for each Gigabit The link exists and Ethernet Port synchronization is achieved. Blinking The link is established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-13 78-13884-06...
Page 68: Fast Ethernet Module Connectors And Leds
8 (connector 7 is shown directly shown directly above it) below it) Link LED (on each connector) Spring-loaded screw (one of two) Duplex LED (on each Ejector (one of two) connector) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-14 78-13884-06...
Page 69: Figure 2-6 16-Port Fast Ethernet Module Connectors And Leds
16 (connector 15 is shown directly shown directly above it) below it) Link LED (on each connector) 5 Spring-loaded screw (one of two) Duplex LED (on each Ejector (one of two) connector) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-15 78-13884-06...
Page 70: Gigabit Ethernet Module Connectors And Leds
Because invisible radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-16 78-13884-06...
Page 71: Figure 2-7 Gigabit Ethernet Module Connectors And Leds
Bicolor status LED (green and Link LED (next to its red) corresponding SFP GBIC) Amber status LED Spring-loaded screw (one of two) LC-type SFP GBIC (one of two) Ejector (one of two) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-17 78-13884-06...
Page 72: Table 2-4 Gigabit Ethernet Module Led Descriptions
See the left status LED for indication. Link Green There is no link. The link exists and synchronization is achieved. Blinking The link is established with transmit or receive activity. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-18 78-13884-06...
Page 73: Session Accelerator Module Leds
Session Accelerator Module LEDs ST AT US ST AT US Bicolor status LED (green and red) 3 Spring-loaded screw (one of two) Amber status LED Ejector (one of two) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-19 78-13884-06...
Page 74: Secure Socket Layer (Ssl) Module Leds
The front panel LEDs on the module indicate its operational status. The SSL module has no connectors. The CSS 11503 supports a maximum of two SSL modules and the CSS 11506 supports a maximum of four SSL modules. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-20 78-13884-06...
Page 75: Figure 2-9 Ssl Module Leds
The module is running power-up self test. (right) Slow blink The module is offline and active. Solid The module is online and not active. See the left status LED for indication. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-21 78-13884-06...
Page 76: Connecting The Console
Never defeat the ground conductor or operate the equipment in the absence of Warning a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-22 78-13884-06...
Page 77: Tools And Supplies
Burndy no. YA6CL2TC10 wish to use a lug other than the one supplied. If you need a lug for the facility end of the ground wire, you must supply it. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-23 78-13884-06...
Page 78: Attaching The Grounding Cable
(supplied in accessory kit) Panduit no. LCC6-10A-L 1 1/16 inch (2.7 cm) (long barrel) Thomas & Betts no. 3/4 inch (1.9 cm) 256-30695-1183(*4*) Burndy no. YA6CL2TC10 7/8 inch (2.2 cm) Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-24 78-13884-06...
Page 79: Figure 2-10 Attaching Grounding Wire To Grounding Lug
Attach the grounding lug to an appropriate grounding point at your site. Proceed to the “Connecting the Power Cord” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-25 78-13884-06...
Page 80: Connecting The Power Cord
Plug the AC power cord connector into the CSS power connector, as shown Figure 2-11. Figure 2-11 Connecting a CSS 11501 AC Power Cord AC power connector Power switch Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-26 78-13884-06...
Page 81: Connecting A Css 11503 Power Cord
Figure 2-12 Connecting a CSS 11503 AC Power Cord 1 0 0 -2 4 0 V 5 0 -6 0 H z 4 3 0 W Power switch AC power connector Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-27 78-13884-06...
Page 82: Connecting A Css 11503 Dc Power Cord
(SELV) requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be connected to a Cisco 11503 system. This requirement ensures that in a catastrophic power source fault condition, hazardous voltages are not present on power terminals and connectors.
Page 83: Figure 2-13 Location Of The Css 11503 Dc Power Supply Connectors
Do not consolidate the end of a conductor by soft soldering prior to installation. Install the wires into the appropriate connector. Make sure that the non-insulated part of each wire is 9 mm (0.35 inches) in length. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-29 78-13884-06...
Page 84: Connecting A Css 11506 Power Cord
The following sections provide information for connecting an AC or DC power cords to a CSS 11506. • Connecting a CSS 11506 AC Power Cord Connecting a CSS 11506 DC Power Cord • Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-30 78-13884-06...
Page 85: Connecting A Css 11506 Ac Power Cord
Plug the power cord into a dedicated 3-wire grounding receptacle. Repeat steps 1 through 3 for each power supply. To power on the CSS, see the “Powering Up the CSS” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-31 78-13884-06...
Page 86: Connecting A Css 11506 Dc Power Cord
DC circuit and switch it off. Warning When you are installing or replacing the unit, the ground connection must always be made first and disconnected last. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-32 78-13884-06...
Page 87 (SELV) requirements in UL1950, CSA 950 3rd Edition, EN 60950, and IEC950, can be connected to a Cisco 11506 system. This requirement ensures that in a catastrophic power source fault condition, hazardous voltages are not present on power terminals and connectors.
Page 88: Table 2-10 Css 11506 To Dc Power Source Cabling
– – The proper wiring sequence is ground to ground, positive to positive, and Warning negative to negative. The ground wire should always be connected first and disconnected last. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-34 78-13884-06...
Page 89: Checking The Dc Power Connection (Css 11503 And Css 11506)
This is an ENERGY HAZARD to you, to the voltmeter, and to the wires connecting the CSS to its power source. To power on the CSS, see the “Powering Up the CSS” section. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-35 78-13884-06...
Page 90: Powering Up The Css
The CSS starts the boot process. For information concerning the boot process on the Cisco 11500 series CSS, refer to the Cisco Content Services Switch Administration Guide. Powering Down the CSS To shut down the CSS gracefully and avoid introducing lost or fragmented files, always use the shutdown command prior to removing power from the CSS.
Page 91: Troubleshooting The Css Hardware Components
CSS 11501 LEDs, see the “Cabling the CSS 11501”section earlier in this chapter. Table 2-11 provides suggestions for correcting problems that may occur with the CSS 11501. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-37 78-13884-06...
Page 92: Table 2-11 Troubleshooting The Css 11501
Obtain technical assistance. NOT STARTING UP Refer to “About This Guide”. For information on log files, refer to the Cisco Content Services Switch Administration Guide. During normal CSS operation, Check the six fans in the chassis. The the following message appears: CSS 11501 is running at a temperature that is too high, as indicated by the x variable.
Page 93: Troubleshooting The Css Modules
- slot / subslot failed, resetting.. Replace the module. Refer to the reference sheet that comes with the replacement module. Power up the CSS to boot the module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-39 78-13884-06...
Page 94 For a CSS 11503, replace the chassis. • • For a CSS 11506, replace the fan module. Refer to the reference sheet that comes with the replacement module. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-40 78-13884-06...
Page 95 CSS software ADI file to install on the disk. If you archived an offline version of your CSS running-config file, copy it back onto the CSS. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-41 78-13884-06...
Page 96: Troubleshooting The Console Interface
CSS to you want. distinguish between different commands and options. Random characters are lost. Set the flow command on the console to XON/XOFF. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-42 78-13884-06...
Page 97: Troubleshooting The Css Power Supply
There is no power to the power supply. Ensure that the CSS 11501 has power. • Check the power switch, power cord, and power source. The power supply failed, obtain technical assistance. • Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-43 78-13884-06...
Page 98 This message is displayed only if the logging level is set to the Info-6 or Debug-7 Note level. A CSS 11506 can contain a maximum of three power supplies, but it requires two functioning power supplies to guarantee service. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-44 78-13884-06...
Page 99 When this message occurs, view the LEDs on the power supply. Figure 2-17 shows the AC power supply LEDs. These LEDs indicate the power status of the supply. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-45 78-13884-06...
Page 100 PS 3 10 0- 24 0V 5A 50 -6 0 -4 8/ -6 0V 10 /8 A Power Supply LEDs: I/P OK and Terminal block DC OK Power switch Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-46 78-13884-06...
Page 101: Table 2-14 Leds Of The Css 11506 Power Supply
The power supply failed. Remove and replace the power supply. Refer to the reference sheet that comes with the replacement supply. After you install the power supply, the CSS automatically brings the power supply into service. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-47 78-13884-06...
Page 102: Troubleshooting The Css Fans
CSS 11501 starts to overheat, the following message appears: Temperature has reached x celsius for slot number The x variable indicates the temperature of the CSS 11501. When a fan failure occurs, obtain technical assistance. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-48 78-13884-06...
Page 103: Troubleshooting The Css 11503 Chassis Fans
If the power supply fan fails, the following message appears: CHMGR: Power Supply Fan Failure. When a fan failure occurs, you must replace the CSS chassis. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-49 78-13884-06...
Page 104: Troubleshooting The Css 11506 Fan Module
When a fan failure occurs, you must replace the fan module to prevent the CSS modules from overheating. Cisco 11500 Series Content Services Switch Hardware Installation Guide 2-50 78-13884-06...
Page 105: Appendix
Electrical Specifications • Environmental Specifications • • Physical Specifications CSS 11501 Bandwidth and Memory Specifications • CSS 11503 and CSS 11506 Module Specifications • • Disk Specifications Supported Standards • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 106: Electrical Specifications
Voltage DC -48.0 to -60.0 VDC -48.0 to -60.0 VDC Current DC (maximum) 9 Amps 18 Amps Power Consumption 430 VA 860 VA (maximum) Heat Dissipation 1468 BTU/hr 2936 BTU/hr Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 107: Environmental Specifications
Not applicable Noise Note G is the unit of acceleration due to gravity, where 1 G equals 32.17 ft/sec (9.81 m/sec Note Grms is the root mean square value of acceleration. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 108: Physical Specifications
Chassis Weight Fully 18.0 lbs. 33.3 lbs. 57.7 lbs. Configured (base system containing (base system containing one SCM and two I/O two power supplies, modules) one SCM, and five I/O modules) Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 109: Css 11501 Bandwidth And Memory Specifications
144 MB default or 288 MB optional (RDRAM) (128 MB or 256 MB of usable (128 MB or 256 MB of usable memory, respectively) memory, respectively) SSL Module Memory 512 MB SDRAM 512 MB SDRAM Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 110: Disk Specifications
The CSS supports the following standards: Transport • • Network • Routing Gateway • • Application • Network Utilities Network Management • Transport The CSS supports the following transport standards: • • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 111: Network
The CSS supports Network Address Translation (NAT), per RFC 1631 gateway standards Application The CSS supports the following application standards: HTTP 1.0, HTTP 1.1 • • TELNET FTP, TFTP • • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 112: Network Utilities
RADIUS Client • • TACACS+ Client HTTP Client • • FTP Daemon • SNTP Network Management The CSS supports the following network management standards: SNMP v1 • SNMP v2c • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 113: Appendix
This appendix contains the following sections that list pinouts for the connectors used with the CSS 11501, CSS 11503, and CSS 11506: RJ-45 Fast Ethernet Connector Pinouts • RJ-45 RS-232 Console Port Pinouts • • RJ-45 Management Connector Pinouts Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 114: Rj-45 Fast Ethernet Connector Pinouts
Ethernet-type cable. Table B-1 RJ-45 Fast Ethernet Connector Pinouts RJ-45 Fast Ethernet Pin Signal Name Numbers RX + RX - TX + Unconnected Unconnected TX - Unconnected Unconnected Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 115: Rj-45 Rs-232 Console Port Pinouts
The following sections provide the pinouts for: Connecting the Console Port to a PC • • Connecting the Console Port to a Terminal Connecting the Console Port to a Modem • Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 116: Connecting The Console Port To A Pc
RJ-45 Rollover DB-9 DTE Console Port to Cable to RJ-45 Adapter to PC Console RJ-45 Rollover DTE Adapter Console PC Console Port Signal Cable Pinouts Pinouts Device Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 117: Connecting The Console Port To A Terminal
Console Port to Terminal Signals and Pinouts RJ-45 Rollover DB-25 DTE Console Port to Cable to RJ-45 Adapter to Console RJ-45 Rollover DTE Adapter Terminal Terminal Port Signal Cable Pinouts Pinouts Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 118: Connecting The Console Port To A Modem
Console Port to Modem Signals and Pinouts RJ-45 Rollover DB-25 DCE Console Port to Cable to RJ-45 Adapter to Console RJ-45 Rollover DCE Adapter Modem Modem Port Signal Cable Pinouts Pinouts Pinouts Device Signal Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 119: Rj-45 Management Connector Pinouts
CSS 11501 front panel and the CSS 11503 or CSS 11506 SCM. Table B-6 RJ-45 Management Connector Pinouts Signal Name Pin Number TX + TX - RX + Unconnected Unconnected RX - Unconnected Unconnected Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 120 Appendix B Cable Connector Pinouts RJ-45 Management Connector Pinouts Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 121: Appendix
Hyperterm. If you connect the modem to the COM port on a PC, you need the following cable and connectors (see Appendix B, Cable Connector Pinouts): • RJ-45-to-RJ-45 rolled cable RJ-45-to-DB-25 modem adapter • • DB-9-to-RJ-45 terminal adapter Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 122: Cabling A Modem To The Css
ST AT US DU PL EX GE 1 LI NK GE 2 LI NK PC MC IA SL OT 1 SL OT 0 C O N SO LE Console connector Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 123 CSS before the CSS logs it out. By default, the timeout is disabled. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 124 Appendix C Connecting a Modem to the CSS Cabling a Modem to the CSS Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06...
Page 125: Appendix
Content Services Switch This appendix provides international agency compliance information applicable to the Cisco Content Services Switches (CSS) 11501, 11503, and 11506. This appendix also provides translations of safety warnings. Use the information in this appendix in conjunction with the information contained in the following guides: •...
Page 126: Agency Approvals
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Agency Approvals Table D-1 lists the regulatory approval requirements for the Cisco 11500 Series CSSs. Table D-1 Regulatory Approval Requirements Regulatory Requirement Category...
Page 127: Fcc Class A Compliance Notice (United States
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or...
Page 128: Fcc Compliance Information Statement (United States
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals FCC Compliance Information Statement (United States) Cisco 11500 Series Content Services Switches (CSS 11503 and CSS 11506) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
Page 129: Ices-003 Class A Compliance Notice (Canada
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals ICES-003 Class A Compliance Notice (Canada) English Statement of Compliance This class A digital apparatus complies with Canadian ICES-003. French Statement of Compliance...
Page 130 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Français: Cet appareil remplit les principales conditions requises et autres dispositions des Directives 73/23/EEC et 89/336/EEC, modifiées par la Directive 93/68/EEC. Íslenska: Þessir búnaður samrýmist lögboðnum kröfum og öðrum ákvæðum tilskipana 73/23/EBE og 89/336/EBE, með...
Page 131: Cispr 22 Class A Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals CISPR 22 Class A Warning This is a class A product. In a domestic environment this product may cause Warning radio interference in which case the user may be required to take adequate measures.
Page 132 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Warnung Dies ist laut Standard des Voluntary Control Council for Interference by Information Technology Equipment (VCCI) ein Produkt der Klasse A. Wenn dieses Gerät in einem häuslichen Umfeld gebaucht wird, können Radiostörungen auftreten.
Page 133: Class A Warning For Taiwan And Other Traditional Chinese Markets
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Agency Approvals Class A Warning for Taiwan and Other Traditional Chinese Markets This is a Class A Information Product, when used in residential environment, it...
Page 134: Class A Emc Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Safety Requirements Class A EMC Warning Warning This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.
Page 135: Laser Safety
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Safety Requirements Mexico NOM-019-SCFI-1998, Safety of Data Processing Equipment. Australia ACA TS001 1997 Test Report and Statement of Compliance AS/NZS3260 incorporating Amendment 1, 2, 3, and 4.
Page 136: Translated Safety Warnings
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Translated Safety Warnings This section repeats, in multiple languages, the warnings contained in this publication. In addition, this section contains translated warnings that can be used...
Page 137 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico’s en dient u op de hoogte te zijn van de standaard praktijken...
Page 138 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les...
Page 139 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Figyelem! FONTOS BIZTONSÁGI ELÕÍRÁSOK Ez a figyelmezetõ jel veszélyre utal. Sérülésveszélyt rejtõ helyzetben van. Mielõtt bármely berendezésen munkát végezte, legyen figyelemmel az elektromos áramkörök okozta kockázatokra, és ismerkedjen meg a szokásos...
Page 140 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER Dette varselssymbolet betyr fare. Du befinner deg i en situasjon som kan forårsake personskade. Før du utfører arbeid med utstyret, bør du være oppmerksom på...
Page 141 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de...
Page 142 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-18 78-13884-06...
Page 143: Battery Handling Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Battery Handling Warning Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer.
Page 144 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Advarsel Det kan være fare for eksplosjon hvis batteriet skiftes på feil måte. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Page 145: Invisible Laser Radiation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Invisible Laser Radiation Warning Warning Invisible laser radiation present. Waarschuwing Onzichtbare laserstraling aanwezig. Varoitus Näkymättömiä lasersäteitä. Attention Rayonnement laser actif mais invisible.
Page 146: Jewelry Removal Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Jewelry Removal Warning Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Page 147 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo può...
Page 148: Installation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Installation Warning Read the installation instructions before you connect the system to its power Warning source. Waarschuwing Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.
Page 149: Radiation From Open Port Aperture
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Ver las instrucciones de instalación antes de conectar el sistema a la red de alimentación. Varning! Läs installationsanvisningarna innan du kopplar systemet till dess strömförsörjningsenhet.
Page 150: Installation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza Quando i cavi in fibra non sono inseriti, radiazioni invisibili possono essere emesse attraverso l’apertura della porta. Evitate di esporvi alle radiazioni e non guardate direttamente nelle aperture.
Page 151 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem, qualifiziertem Personal gestattet werden. Figyelem! A berendezést csak szakképzett személyek helyezhetik üzembe, cserélhetik és tarthatják karban.
Page 152: Two Person Lifting Requirement
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Two Person Lifting Requirement Warning Two people are required to lift the chassis. To prevent injury, keep your back straight and lift with your legs, not your back.
Page 153: Lifting The Chassis Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Se requieren dos personas para elevar el chasis. Para evitar lesiones, mantenga su espalda en posición recta y levante con sus piernas, no con su espalda.
Page 154 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avertissement Il faut être deux pour lever le châssis. Soulevez-le en le prenant par son bord inférieur et levez-le à deux mains. Pour éviter tout risque deblessure, veillez à...
Page 155: Chassis Installation Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Atención! Se necesitan dos personas para levantar el chasis. Sujete el chasis con las dos manos por debajo del borde inferior y levántelo. Para evitar lesiones, mantenga la espalda recta y levante con la fuerza de las piernas y no de la espalda.
Page 156: Lightning Activity Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Zum Einbauen des Chassis in das Gerätegestell werden mindestens drei Personen benötigt: Zwei Personen sollten das Chassis festhalten, während eine dritte Person die Befestigungsschrauben festzieht.
Page 157 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Ne pas travailler sur le système ni brancher ou débrancher les câbles pendant un orage. Warnung Arbeiten Sie nicht am System und schließen Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Page 158: Disconnect Device Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Disconnect Device Warning Warning A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Waarschuwing Er moet een gemakkelijk toegankelijke, tweepolige stroomverbreker opgenomen zijn in de vaste bedrading.
Page 159: Cisco 11500 Power Source
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Power Source Only a DC power source that is isolated from AC mains with reinforced Warning insulation, and that complies with the other safety extra-low voltage (SELV) requirements in UL950, CSA 950, EN 60950, and IEC950, can be connected to a Cisco 11500 system.
Page 160 Bare likestrømskilder som er isolert fra vekselstrømledninger med ekstra isolasjon, og som oppfyller andre sikkerhetskrav for lavspenning (SELV) i UL950, CSA 950, EN 60950 og IEC950 kan kobles til et Cisco 11500-system. Disse kravene sikrer at hvis det skulle oppstå en katastrofal feil i en strømkilde, er det ikke farlig spenning tilstede på...
Page 161: Dc Power Supply Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Sólo una fuente de alimentación de CC con aislamiento reforzado de las fuentes principales de corriente alterna y que cumpla con los demás...
Page 162 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention La figure illustre le bloc de connexion de l’alimentation en courant continu. Câblez l'alimentation en courant continu en fixant les cosses appropriées aux extrémités câblées ou sans utiliser de cosses, conformément au schéma.
Page 163 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! La figura muestra la caja de bornes de la fuente de alimentación. Cablee la fuente de alimentación de corriente continua, utilizando las lengüetas de conexión apropiadas en el extremo del cable, tal como se muestra, o sin...
Page 164: Power Supply Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Power Supply Warning Warning This unit might have more than one power supply connection; all connections must be removed completely for you to completely remove power from the unit.
Page 165: Ground Conductor Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings ¡Advertencia! Esta unidad podría tener más de una conexión de suministros de alimentación; para eliminar la alimentación por completo, deben desconectarse completamente todas las conexiones.
Page 166 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Dieses Gerät muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Gerät ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zuständige Inspektionsbehörde oder...
Page 167: Installation And Replacement Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Installation and Replacement Warning When you install or replace the unit, the ground connection must always be Warning made first and disconnected last.
Page 168: Use Copper Conductors Only Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza In fase di installazione o sostituzione dell'unità, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo. Advarsel Når enheten installeres eller byttes, må jordledningen alltid tilkobles først og frakobles sist.
Page 169: Short-Circuit Protection Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso Utilize apenas fios condutores de cobre. ¡Advertencia! Emplee sólo conductores de cobre. Varning! Använd endast ledare av koppar. Short-circuit Protection Warning...
Page 170 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Warnung Für dieses Produkt ist eine Kurzschlußsicherung (Überstromsicherung) erforderlich, die als Teil der Gebäudeinstallation zur Verfügung gestellt wird. Die Installation sollte nur in Übereinstimmung mit den nationalen und regionalen Vorschriften zur Verkabelung erfolgen.
Page 171: Faceplates And Cover Panels Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Faceplates and Cover Panels Warning Blank faceplates and cover panels serve three important functions: they Warning prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment;...
Page 172 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Attention Ne jamais faire fonctionner le système sans que l’intégralité des cartes, des plaques métalliques et des panneaux avant et arrière ne soient fixés à leur emplacement.
Page 173 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Aviso As faces furadas e os painéis de protecção desempenham três importantes funções: previnem contra uma exposição perigosa a voltagens e correntes existentes no interior do chassis;...
Page 174: Power Module Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Power Module Warning Warning Never install an AC power module and a DC power module in the same chassis. Waarschuwing Een voedingsmodule met wisselstroom mag nooit samen met een gelijkstroomvoedingsmodule in het chassis geïnstalleerd worden.
Page 175 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza Non installare un modulo di alimentazione in corrente alternata e un modulo di alimentazione in corrente continua nello stesso chassis. Advarsel En vekselstrømmodul og en likestrømmodul må...
Page 176: Ground Conductor Warning
Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Ground Conductor Warning Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor.
Page 177 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Avvertenza Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di protezione né usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto.
Page 178 Appendix D Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch Translated Safety Warnings Cisco 11500 Series Content Services Switch Hardware Installation Guide D-54 78-13884-06...
Page 179: I N D E X
1-13 CSS 11503 overview CSS 11506 unpacking CSS 11503 Fast Ethernet Module 2-14 Gigabit Ethernet Module installing 2-16 1-14 Switch Control Module mounting bracket installation 2-11 1-15 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-1 78-13884-06...
Page 180 8-port LEDs and connectors 2-14 disk LED definitions 2-16 failure 2-38, 2-41 pinouts specifications front-mounting documentation CSS 11501 brackets 1-13 chapter contents CSS 11503 brackets 1-15 related xvii CSS 11506 brackets 1-17 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-2 78-13884-06...
Page 181 1-19, 1-24 CSS 11506 slot restrictions 1-17 1-21 lifting chassis (CSS 11503 and CSS specifications 11506) troubleshooting 2-39 module 1-24 unpacking 1-24 qualified personnel (warning) international agency compliance information Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-3 78-13884-06...
Page 182 11506) troubleshooting 2-43, 2-44 lightning warning preinstallation requirements 1-11 removing jewelry protocols, supported A-6 to A-8 US electrical codes safety warning 1-12, 1-14, D-1 screws, for grounding 2-23, 2-24 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-4 78-13884-06...
Page 183 LEDs 2-12 wiring LED definitions 2-5, 2-13 chassis ground 2-23 passive switchover 1-26 safety (warning) tools and equipment required tools and supplies, connecting chassis to ground 2-23 Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-5 78-13884-06...
Page 184 Index Cisco 11500 Series Content Services Switch Hardware Installation Guide IN-6 78-13884-06...

This manual is also suitable for:

Css11503-ac 11506 - css content services switch Css 11501 11503 - css content services switch

Cisco CSS11501 - 100Mbps Ethernet Load Balancing Device Hardware Installation Manual

About this Guide

Cisco.com

Chapter 1 Unpacking and Installing the CSS

Figure 1-1 Front-Mounting the Mounting Brackets on the CSS 11501

Figure 1-2 Front-Mounting the Mounting Brackets on the CSS 11503

Table 1-3 CSS 11503 Chassis Slot Restriction

Table 1-4 CSS 11506 Chassis Slot Restriction

Figure 1-6 Fully-Configured CSS 11503

Figure 1-3 MID-Mounting the Mounting Brackets on the CSS 11503

Figure 1-4 Front-Mounting Position of the CSS 11506 Mounting Brackets

Figure 1-9 Installing a PCMCIA Cover on an SCM

Chapter 2 Cabling and Troubleshooting the CSS

Figure 2-3 CSS 11506 Content Services Switch

Figure 2-4 Switch Control Module Connectors and Leds

Table 2-2 Switch Control Module LED Descriptions

Appendix

Specifications

Appendix

Cable Connector Pinouts

Appendix

Connecting a Modem to the CSS

Appendix

Regulatory Compliance and Safety Information for the Cisco 11500 Series Content Services Switch

I N D E X

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for Cisco CSS11501 - 100Mbps Ethernet Load Balancing Device

Summary of Contents for Cisco CSS11501 - 100Mbps Ethernet Load Balancing Device